headlamp PEUGEOT 207 2008 Owners Manual

FAMILIARISATION

1. Audio equipment steering wheel
control.

2. Steering lock and ignition.

3. Wipers/wash-wipe/trip computer
controls.

4. Instrument panel.

5. Driver's air bag.
Horn.

6. Dynamic stability control
(ESP/ASR) button.
Rear parking assistance button.
Central locking button.
Alarm button.
Electric child lock button.

7. Gear lever.

8. Handbrake.

9. Panoramic roof shutter control
(SW).

10. Exterior mirror controls.
Electric window controls.
Rear electric windows deactivation control.

11. Headlamp height adjustment.

12. Front door window de-icing vent.

13. Side adjustable and closing vent.

14. Windscreen de-icing vent.

FAMILIARISATION
Lights
Ring A Switching on "AUTO" mode

 Push the control downwards and
release it.
Ring B Control A: windscreen wipers

2. Fast wipe.

1. Normal wipe.

I. Intermittent wipe.

0. Park.

AUTO  Automatic wiping or single
wipe.
Wash-wipe: pull the control towards you.


85
Wipers
Switching off "AUTO" mode

 Push the control upwards and return
it to position "0" .

 87
Ring B: rear wiper

 81
 86
Lights off.
Side lights.
Dipped/main beam headlamps.
Rear fog lamps.
or
Front and rear fog lamps.
Park.
Intermittent wipe.
Wash-wipe.
Automatic lighting.

!
19
The indicator/warning light comes
on continuously or fl ashes.
Some indicator/warning lights may
light in two different ways. Only by
relating the type of lighting to the
vehicle operating status can it be
ascertained whether the situation
is normal or whether a fault has oc-
curred.
Indicator and warning lights
Visual indicators which inform the driv-
er when a system comes into opera-
tion (operation or deactivation indicator
lights) or of the occurrence of a fault
(warning light).
Associated warnings
The lighting of certain indicator/warning
lights may be accompanied by an audible
signal and a message on the multifunction
display. Operation indicator lights
The lighting of one of the following indica-
tor lights confi rms that the corresponding
system has come into operation.

Left-hand direction
indicator.

Handbrake applied.

Right-hand direction
indicator.

Main beam headlamps.

Dipped headlamps.

Diesel engine pre-heating.
Wait until this switches off before
operating the starter.

Front fog lamps.

Rear fog lamps.
When the ignition is switched on
The warning lights come on for a few
seconds when the vehicle ignition is
switched on.
When the engine is started, these warning
lights should switch off.
If they remain on, before moving off,
consult the text relating to the warning
light concerned.

22
Air bags.
The lighting of this warning
light indicates the occurrence
of a fault in one of the air bags
(front, side or curtain) or pre-tensioning
seat belt systems.
Dynamic stability control
(ESP).
The ESP system is activated auto-
matically when the vehicle is started.
Unless the system has been deactivated,
continuous lighting of this warning light
and fl ashing of the indicator light on the
button indicate the occurrence of a fault
in this system.
Engine autodiagnostics
system.
The lighting of this warning light
indicates the occurrence of a
fault in the engine management system.
Flashing of this warning light indicates
the occurrence of a fault in the emission
control system.
Engine oil pressure.
The lighting of this warning light
indicates the occurrence of a
fault in the engine lubrication
circuit. It is imperative that the vehicle is
stopped as soon as it is safe to do so. Battery charge.
The lighting of this warning light
indicates the occurrence of a
fault in the battery charging cir-
cuit (dirty or loose terminals, slack or
cut alternator belt, ...).
Braking.
The lighting of this warning light
indicates the occurrence of a fault
in one of the braking systems:
- signifi cant drop in the level in the cir- cuit,
- electronic brake force distribution (EBFD) faulty (if lit at the same time
as the ABS warning light).
It is imperative that the vehicle is
stopped as soon as it is safe to do so.
If the vehicle is moving, check that the
handbrake has been released fully.
Low fuel level.
The lighting of this warning light
indicates that there is enough
fuel left to drive approximately
30 miles (50 km).
The capacity of the fuel tank is approxi-
mately 50 litres.
Maximum coolant
temperature.
The lighting of this warning light
indicates an excessively high
temperature in the cooling system. It is
imperative that the vehicle is stopped
as soon as it is safe to do so. Door open.
A door, the boot, the rear screen
or the bonnet is still open:
- if the speed is below 6 mph (10 km/h),
this warning light comes on continuously,
- if the speed is above 6 mph (10 km/h), this warning light comes on continuously,
accompanied by an audible signal.
Seat belt not fastened/
unfastened.
The lighting of this warning light
indicates that the driver * and/or
the front passenger has not fastened
his seat belt or has unfastened it.
It also indicates that one or more rear
passengers have unfastened their seat
belt.
Power steering.
The lighting of this warning light
indicates the occurrence of a fault
in the electric power steering.
Presence of water
in diesel * .
The lighting of this warning light
indicates the presence of water
in the diesel fi lter.
There is a risk of damage to the injection
system on Diesel engines.
Directional headlamps.
Flashing of this warning light
indicates the occurrence of a
fault in the directional head-
lamps system.
* According to country.

!
29
Options
Once the "Options" menu has been se-
lected, you can start diagnostics of the
status of the equipment (active, not active,
faulty). Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Display settings
Once the "Display settings" menu has
been selected, you can gain access to
the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.

 Wait for approximately ten sec-
onds without any action to allow
the changed data to be recorded or
press the "ESC" button to cancel.
The display then returns to the normal
display.
Once the "Vehicle confi guration" menu
has been selected, you can activate or
deactivate the following equipment:
- wiper linked with reverse gear (refer to the "Visibility" section),
- directional headlamps (refer to the "Visibility" section),
- "follow-me-home" lighting (refer to the "Visibility" section).
For safety reasons, it is imperative
that confi guration of the multifunc-
tion displays by the driver takes
place when stationary.
Units
Once the "Units" menu has been se-
lected, you can change the units of the
following parameters:
- temperature (°C or °F),
- fuel consumption (l/100 km, mpg or
km/l).
Vehicle confi guration

 Once you have selected a setting,
press the "OK" button to change its
value.

!
31
For safety reasons, it is imperative
that confi guration of the multifunc-
tion displays by the driver takes
place when stationary.
Display settings
Once the "Display settings" menu has
been selected, you can gain access to
the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Units
Once the "Units" menu has been se-
lected, you can change the units of the
following parameters:
- temperature (°C or °F),
- fuel consumption (l/100 km, mpg or
km/l).

 Once you have selected a setting,
press the " " or " " buttons to
change its value.

 Press the " " or " " buttons to
switch respectively to the previous
or next setting.

 Press the "OK" button to record the
change and return to the normal dis-
play or press the "ESC" button to
cancel.
Vehicle confi guration
Options
Once the "Options" menu has been se-
lected, you can start diagnostics of the
status of the equipment (active, not active,
faulty).
Once the "Vehicle Confi guration" menu
has been selected, you can activate or
deactivate the following equipment:
- wiper linked with reverse gear (refer
to the "Visibility" section),
- directional headlamps (refer to the "Visibility" section),
- "follow-me-home" lighting (refer to the "Visibility" section).

32
MONOCHROME SCREEN C General menu
Displays on the screen
This displays the following information:
- the time,
- the date,
- the outside temperature * (this fl ash- es if there is a risk of ice),
- the status of the accesses (doors, boot, ...),
- the audio sources (radio, CD, ...),
- the trip computer (refer to the end of the section).
Warning messages (e.g.: "Emission
control system faulty") or information
messages (e.g.: "Automatic switching
on of the headlamps activated") may ap-
pear temporarily. These can be cleared
by pressing the "
ESC" button. Controls
From the RD4 audio equipment control
panel, you can:

 press the "MENU" button to gain
access to the general menu ,

 press the " " or " " buttons to
scroll through the items on the
screen,

 press the "MODE" button to change
the permanent application (trip com-
puter, audio source, ...),

 press the " " or " " buttons to
change a setting value,

 press the "OK" button to confi rm,
or

 press the "ESC" button to abandon
the operation in progress. "Audio functions" menu
With the RD4 audio equipment switched
on, once this menu has been selected
you can activate or deactivate the func-
tions linked with use of the radio (RDS,
REG, RadioText), the CD or the CD
changer (introscan, shuffl e, CD repeat).
For further details concerning the "Au-
dio functions" application, refer to the
RD4 part of the "Audio and Telematics"
section.
* With air conditioning only.

 Press the "MENU" button to gain
access to the general menu :
- audio functions,
- trip computer (refer to the end of the section),
- personalisation-confi guration,
- telephone (hands-free kit).

 Press the " " or " " buttons to se-
lect the menu required, then confi rm
by pressing the "OK" button.

!
34
Defi ne the vehicle parameters
Once this menu has been selected, you
can activate or deactivate the following
equipment:
- wiper linked with reverse gear (refer to the "Visibility" section),
- directional headlamps (refer to the "Visibility" section),
- "follow-me-home" lighting (refer to the "Visibility" section). Selection of the language
Once this menu has been selected, you
can change the screen display language
(Deutsch, English, Espanol, Français,
Italiano, Nederlands, Portugues,
Portugues-Brasil).
"Telephone" menu
With the RD4 audio equipment switched
on, once this menu has been select-
ed you can confi gure your Bluetooth
hands-free kit (matching), consult the
various telephone directories (calls log,
services, ...) and manage your commu-
nications (pick up, hang up, call waiting,
secret mode, ...).
For further details concerning the "Tele-
phone" application, refer to the RD4 part
of the "Audio and Telematics" section.
Example: setting of the duration of the
"follow-me-home" lighting
"Personalisation-Configuration"
menu
Once this menu has been selected, you
can gain access to the following fun-
ctions:
- defi ne the vehicle parameters,
- display confi guration,
- selection of the language.
 Press the " " or " " buttons, then
the "
OK" button to select the menu
required.

 Press the " " or " " buttons,
then the "
OK
" button to select the
"Follow-me-home lighting" line.

 Press the " " or " " buttons to set
the value required (15, 30 or 60 se-
conds), then press the "
OK
" button
to confi rm.

 Press the " " or " " buttons, then
the " OK " button to select the "OK"
box and confi rm or press the "ESC"
button to cancel.
Display confi guration
Once this menu has been selected,
you can gain access to the following
settings:
- brightness-video setting,
- date and time setting,
- selection of the units.
For safety reasons, it is imperative
that confi guration of the multifunc-
tion displays by the driver takes
place when stationary.

35
COLOUR SCREEN 16/9
Displays on the screen When the RT4 GPS audio/telephone is
switched on, select the menu which cor-
responds to the following applications:
- the satellite navigation system,
- the guidance on the map,
- the traffi c information,
- the audio sources (radio, CD, Juke-
box, ...),
- the phone books and the telephone functions,
- the confi guration of the screen and the setting of the parameters of the
vehicle’s equipment,
- the displaying of a video,
- the vehicle diagnostics. Controls
When the ignition is switched on, this
displays the following information auto-
matically and directly:
- the time,
- the date,
- the outside temperature (if there is a risk of ice, you are warned by a
message).
Warning messages (e.g.: "Fuel level
low") and vehicle function status mes-
sages (e.g.: "Automatic switching on of
the headlamps activated") may appear
temporarily. These can be cleared by
pressing the "ESC" button. From the RT4 GPS audio/telephone
control panel, to select one of the ap-
plications:

 press the "MENU" button to gain
access to the general menu ,

 turn the navigator to move the se-
lection,

 press the navigator to confi rm the
selection,
or

 press the "ESC" button to abandon
the operation in progress and return
to the previous display.
For further details concerning these ap-
plications, refer to the RT4 part of the
"Audio and Telematics" section.
General menu

36
Defi ne the vehicle parameters
Once the "Defi ne the vehicle parame-
ters" menu has been selected, you can
activate or deactivate certain driving
and comfort equipment:
- wiper linked with reverse gear (refer to the "Visibility" section),
- directional headlamps (refer to the "Visibility" section),
- "follow-me-home" lighting and duration (refer to the "Visibility" section).
Example: setting the duration of the "follow-
me-home" lighting

 Turn the navigator to select the

"Lighting confi guration" menu,
then press it to confi rm.

 Select the line "Duration of the "follow-
me-home" lighting" then confi rm.
"Configuration" menu

 Press the "MENU" button on the
RT4 GPS audio/telephone to gain
access to the general menu .

 Turn the navigator to select the

"Confi guration" menu, then press
it to confi rm. Once this menu has been selected, you
can gain access to the following func-
tions:

 Select the duration then press the
navigator.

 Turn the navigator to set the value
required (15, 30 or 60 seconds),
then press the navigator.

 Select the "OK" box, then confi rm.