Peugeot 207 Dag 2007 Repair Manual

63
INTERIOR LAYOUT
1. Glove box with light (see details on following page)
2. Storage compartment with non-slip mat
3. Card holder
4. Door tray
5. Storage compartment with non-slip mat
6. Ashtray with light/Lighter (see details on following page)
7. Storage compartments
8. Can holder

64
Glove box with light
This has an upper open storage com-partment, a recess and locations for storing a bottle of water, the vehicle’s handbook, ...
Its lid has locations for storing a pen, a pair of spectacles, tokens, cards, a can, ...
It may be fitted with a lock.
 To open the glove box, raise the handle.
It is lit when the lid is opened.
Ashtray with light/Lighter
 Raise the lid to gain access to the ashtray and the lighter.
 To empty the ashtray, after opening, remove its receptacle.
 To use the lighter, press it and wait a few seconds until it pops out auto-matically.
 To connect a 12 V accessory (max power: 100 Watts), remove the lighter and connect the appropriate adaptor.
It houses the front passenger air bag disarming switch A and three sockets* B for connecting audio/video equipment (refer to the "Audio and Telematics" section to activate the auxiliary input sockets).
If the vehicle is fitted with air condi-tioning, it provides access to the ven-tilation nozzle C, which can be opened or closed, distributing the same condi-tioned air as the vents in the passenger compartment.
* With DT colour display only.

65
BOOT LAYOUT
(SALOON)
1. Rear shelf(see details on following page)
2. Hooks(see details on following page)
3. Stowing rings
4. Luggage retaining net(see details on following page)

i
66
Hooks
Hooked onto the stowing rings, this ena-bles you to secure your luggage, either to the bottom of the boot or to the back of the rear seats.
Rear shelf (Saloon)
To remove the shelf:
 unhook the two cords,
 raise the shelf slightly, then remove it.
You have two storage options:
- either upright behind the front seats,- or upright behind the rear seats.
The hooks permit the securing of shop-ping bags.
Luggage retaining net

67
BOOT LAYOUT (SW)
1. Load space cover(see details on following page)
2. 12 V accessories socket(see details on following page)
3. Hooks(see details on previous page)
4. Retaining straps
5. Stowing rings
6. Luggage retaining net(see details on previous page)
7. High load retaining net(see details on following page)
8. Storage box
9. Storage net
10. Storage box(refer to the section "Practical information - § Changing a wheel")

i
68
Load space cover (SW)
This consists of three sections which can be folded back on each other.
There are two storage options:
- either folded on itself near the rear seats (1),- or unfolded and placed flat on the boot floor (2).
To fold it from the boot:
 take hold of the load space cover by its strap A,
 fold it concertina-style to the rear seats.
To unfold it from the boot:
 take hold of the load space cover by its strap A,
 unfold it to the boot pillars.
To gain access from the rear seats:
 raise the front section of the load space cover using the handle B.
12 V accessories socket (SW)
 In order to connect a 12 V accessory(max power: 100 Watts), remove the cap and connect the appropriate adaptor.
 Turn the key to the ignition position.

69
High load retainingnet (SW)
Hooked onto the upper fixings and onto the stowing rings or lugs, this permits use of the entire loading volumeup to the roof:
- behind the rear seats (row 2) when the load space cover is absent,- behind the front seats (row 1) when the rear seats are folded.
To use it in row 1:
 open the covers of the upper fixings 1,
 unroll the high load retaining net,
 position one of the ends of the net's metal bar in the corresponding upper fixing 1, then do the same with the other end,
 slacken the straps fully,
 fix the snap hook of each of the straps on the corresponding lug, located under the bench seat cush-ion,
 fold the rear seats,
 tighten the straps without raising the bench seat,
 check that the net is hooked and tightened correctly.
To use it in row 2:
fold or remove the load space cover,
open the covers of the upper fixings 2,
 unroll the high load retaining net,
 position one of the ends of the net's metal bar in the corresponding upper fixing 2, then do the same with the other end,
 attach the hook of each of the net's straps in the corresponding stowing ring,
 tighten the straps,
 check that the net is hooked and tightened correctly.

!
i
70
REMOTE CONTROL KEY
System which permits central unlocking or locking of the vehicle using the lock or remotely. It also locates and starts the vehicle, as well as providing protec-tion against theft.
Unfolding the key
 First press button A to unfold the key.
Unlocking the vehicle
Unlocking is confirmed by rapid flashing of the direction indicators for approxi-mately two seconds.
According to version, the exterior mir-rors unfold at the same time.
Locking the vehicle
Normal locking using the remote control
Deadlocking using the remote control
 Press the closed padlock to lock the vehicle.
 Press the closed padlock again within five seconds to deadlock the vehicle.
 Press the open padlock to unlock the vehicle.
Unlocking using the key
 Turn the key to the left in the driver's door lock to unlock the vehicle.
 Press the closed padlock to lock the vehicle.
Normal locking using the key
 Turn the key to the right in the dri-ver's door lock to lock the vehicle.
Locking is confirmed by fixed lighting of the direction indicators for approximate-ly two seconds.
According to version, the exterior mir-rors fold at the same time.
Unlocking using the remotecontrol
Deadlocking using the key
 Turn the key to the right in the dri-ver's door lock to lock the vehicle.
 Turn the key to the right again within five seconds to deadlock the vehicle.
Deadlocking is confirmed by fixed light-ing of the direction indicators for ap-proximately two seconds.
According to version, the exterior mir-rors fold at the same time.

!i
i
71
Folding the key
 First press button A to fold the key.
Confidential card
Electronic engine immobiliser
The key contains an electronic chip which has a special code. When the ignition is switched on, this code must be recognised in order for starting to be possible.
This electronic engine immobiliser locks the engine management system a few minutes after the ignition is switched off and prevents starting of the engine by anyone who does not have the key.
Anti-theft protectionThis is given to you with the duplicate keys on delivery of your vehicle.
It bears the identification code necessary for any work on the electronic engine im-mobiliser by a PEUGEOT dealer.
This code is hidden by a film which should not be removed until necessary.
In the event of a malfunction, you are informed by lighting of this warning light, an audible signal and a message on the multifunction display.
In this case, your vehicle does not start; contact a PEUGEOT dealer as soon as possible.
Unlocking and partial opening of the rear screen (SW)
 Press this button for more than two seconds to par-tially open the rear screen. This action will unlock the vehicle first.

i
72
Starting the vehicle
 Insert the key in the starter.
 Wait a few seconds for the starting code to be recognised.
 Turn the key fully towards the fascia to position 3 (Starting).
 When the engine starts, release the key.
Switching the vehicle off
 Immobilise the vehicle.
 Turn the key fully towards you to position 1 (Stop).
 Remove the key from the starter.
Remote control problem
Following disconnection of the vehicle battery, replacement of the remote con-trol battery or in the event of a remote control malfunction, you can no longer unlock, lock or locate your vehicle.
 First of all, use the key in the lock to unlock or lock your vehicle.
 Then, reinitialise the remote control.
If the problem persists, contact a PEUGEOT dealer as soon as possible.
Changing the battery
Battery ref.: CR1620/3 volts.
Reinitialisation
 Switch off the ignition.
 Turn the key to position 2 (Ignition).
 Press the closed padlock immedi-ately for a few seconds.
 Switch off the ignition and remove the key from the starter.
The remote control is fully operational again.
 Unclip the casing using a coin at the notch.
 Slide the flat battery out of its loca-tion.
 Slide the new battery into its location observing the original direction.
 Clip the casing.
 Reinitialise the remote control.
If the battery is flat, you are in-formed by lighting of this warn-ing light, an audible signal and a message on the multifunction display.
Locating your vehicle
To locate your vehicle, if you have locked it, in a car park:
 press the closed padlock, the cour-tesy lights come on and the direction indicators flash for a few seconds.