Peugeot 3008 Hybrid 4 2012 - RHD (UK. Australia) Repair Manual

59
IN
S
Following this operation, if you
wish to disconnect the battery,
lock the vehicle and wait at
least fi ve minutes for the zero reset
to be taken into account.






Service indicator zero reset
After each service, the service indicator
must be reset to zero.
The procedure for resetting to zero is as
follows:


)
switch off the ignition,

)
press and hold the trip distance re-
corder zero reset button,

)
switch on the ignition; the distance re-
corder display begins a countdown,

)
when the display indicates "=0"
, re-
lease the button; the spanner disap-
pears.

The distance remaining may
be weighted by the time fac-
tor, depending on the driving
conditions.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.

Service overdue
For 5 seconds after the ignition is
switched on, the spanner fl ashes
to
indicate that the service must be carried
out as soon as possible.

Example:
the service is overdue by
186 miles (300 km).
For 5 seconds after the ignition is
switched on, the screen indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes its
normal operation. The spanner re-
mains on
.
Retrieving the service information
You can access the service information
at any time.


)
Press the trip distance recorder zero
reset button.
The service information is displayed
for a few seconds, then disappears.

IN
S

The level shown will only be
correct if the vehicle is on level
ground and the engine has been
off for more than 30 minutes.
Engine oil level indicator
System which informs the driver wheth-
er the engine oil level is correct or not. This information is indicated for a few
seconds when the ignition is switched
on, after the service information.

Oil level correct

Oil level low
Oil level indicator fault

Dipstick
This is indicated by the fl ashing of "OIL"
,
linked with the service warning lamp, ac-
companied by an audible signal and a
message in the multifunction screen.
If the low oil level is confi rmed by a
check using the dipstick, the level must
be topped up to prevent damage to the
engine. This is indicated by the fl ashing of "OIL

--"
.
Contact a PEUGEOT dealer or a qualifi ed
workshop.
Refer to the "Checks" section to locate
the dipstick and the oil fi ller cap on your
engine.
There are 2 marks on the
dipstick:


- A
= max; never exceed
this level (risk of damage
to the engine),

- B
= min; top up the level
via the oil fi ller cap, using
the grade of oil suited to
your engine.

61
IN
S
Total distance recorder
System which measures the total distance
travelled by the vehicle during its life.
Lighting dimmer
System for manual adjustment of the
brightness of the instrument panel in re-
lation to the exterior brightness.
The total and trip distances are dis-
played for thirty seconds when the ig-
nition is switched off, when the driver's
door is opened and when the vehicle is
locked or unlocked.
Tr ip distance recorder


)
With the ignition on, press the but-
ton until zeros appear.

Activation
When the vehicle lighting is on:


)
press the button to change the
brightness of the instrument panel,

)
when the lighting reaches the mini-
mum setting, release the button,
then press again to increase it,
or


)
when the lighting reaches the maxi-
mum setting, release the button,
then press again to reduce it,

)
when the lighting reaches the level
of brightness required, release the
button.

When the vehicle lighting is
on, you cannot switch the in-
strument panel lighting off but
you can adjust it to minimum.

Deactivation
When the lighting is off, or in day mode
on vehicles fi tted with daytime running
lamps, pressing the button does not
have any effect.


To conform to legislation in the country
you are crossing, change the units of
distance (miles or km) via the confi gu-
ration menu.

System which measures a distance
travelled during a day or other period
since it was reset to zero by the driver.

M
U
62
MONOCHROME SCREEN C (WITH PEUGEOT CONNECT SOUND (RD5)) Main menu

Displays in the screen

Displays according to context:


- time,

- date,

- ambient temperature with air condi-
tioning (the value displayed fl ashes if
there is a risk of ice),

- status of the openings (doors, boot...),

- audio functions,

- trip computer (see "trip computer"),

- alert messages,

- screen and vehicle equipment pa-
rameter setting menus.



"Audio functions" menu Controls

From the audio equipment control panel,
you can:


)
press the " MENU
" button for access
to the main menu
,

)
press the " 
" or " 
" buttons to scroll
through the items on the screen,

)
press the " MODE
" button to change
the permanent application (trip com-
puter, audio source...),

)
press the " 
" or " 
" buttons to
change a setting value,

)
press the " OK
" button to confi rm,
or

)
press the " ESC
" button to abandon
the operation in progress.




)
Press the "MENU"
button for access
to the main menu
:


- audio functions,

- trip computer (see "trip computer"),

- personalisation-confi guration,

- telephone (Bluetooth system).



For more information on the
"Audio functions" application,
refer to the Peugeot Connect
Sound (RD5) section.





)
Press the " 
" or " 
" button to se-
lect the menu required, then confi rm
by pressing the " OK
" button.



With the audio equipment switched on,
once this menu has been selected you
can activate or deactivate the functions
linked with use of the radio (RDS, REG,
RadioText) or CD (introscan, shuffl e,
CD repeat).

M
U
63

"Trip computer" menu




)
Press the "MENU"
button to gain
access to the general menu.

)
Press the arrows, then the "OK"
button
to select the "Trip computer"
menu.




)
On the "Trip computer"
menu, select
one of the applications:

Enter the distance to the destination
This allows you to enter an approximate
value for the distance to the fi nal destina-
tion.

Once this menu has been selected, you
can consult information concerning the
status of the vehicle (alert log, status of
the functions...).

Defi ne the vehicle parameters
Once this menu has been selected, you
can activate or deactivate the following
equipment (according to country):


- wiper linked with reverse gear (see
"Visibility"),

- selective unlocking (see "Access"),

-
guide-me-home lighting (see "Visibility"),


- interior mood lighting (see "Visibility"),

-
daytime running lamps (see "Visibility"),


- directional headlamps (see "Visibility"),

- automatic or manual parking brake
(see "Driving"),

- ...


"Personalisation-
Configuration" menu

Once this menu has been selected, you
can gain access to the following functions:


- defi ne the vehicle parameters,

- display confi guration,

- choice of language.



Alert log
This summarises the active warning
messages, displaying them in succes-
sion in the multifunction screen

Status of functions
This summarises the active or inactive
status of the functions present on the
vehicle.

M
U
64

Display confi guration
Once this menu has been selected, you
have access to the following settings:


- brightness-video setting,

- date and time setting,

- selection of the units.


Choice of language
Once this menu has been selected,
you can change the screen display
language (Deutsch, English, Espanol,
Français, Italiano, Nederlands, Portugues,
Portugues-Brasil, Türkçe * ).


Example: setting of the duration of the
guide-me-home lighting


)
Press the " 
" or " 
" buttons, then
the " OK
" button to select the menu
required.




)
Press the " 
" or " 
" buttons, then the
" OK
" button to select the "Guide-me-
home headlamps" line.




)
Press the " 
" or " 
" buttons to set the
value required (15, 30 or 60 seconds),
then press the " OK
" button to confi rm.



)
Press the " 
" or " 
" buttons, then
the " OK
" button to select the " OK
"
box and confi rm or press the " ESC
"
button to cancel.



"Telephone" menu
With the audio equipment switched on,
once this menu has been selected you
can confi gure your Bluetooth hands-free
kit (pairing), consult the various telephone
directories (calls log, services...) and man-
age your communications (pick up, hang
up, call waiting, secret mode...).

For safety reasons, confi gu-
ration of the multifunction
screen by the driver must only
be done when stationary.

For more information on the
"Telephone" application, refer
to the Peugeot Connect Sound
(RD5) section.

*
According to country.

M
U
65
16/9 HIGH DEFINITION RETRACTABLE COLOUR SCREEN(WITH PEUGEOT CONNECT MEDIA NAVIGATION(NG4 3D))
Displays in the screen
Displays according to context:


- time,

- date,

- altitude,

- ambient temperature (the value dis-
played fl ashes if there is a risk of ice),

- audio functions,

-
telephone and address book information,


- satellite navigation system information.

-
screen and navigation system parameter
setting menus,

- information on hybrid fl ows.



Controls


From the Peugeot Connect Media Navi-
gation (NG4 3D) control panel, to select
one of the applications:


)

press the dedicated "RADIO"
, "MEDIA"
,
"NAV"
, "TRAFFIC"
, "ADDR BOOK"
or
"SETUP"
button for access to the cor-
responding menu,

)
turn the navigator to move the selection,


)
press the navigator to confi rm the
selection,
or

)
press the "ESC"
button to abandon
the current operation and return to
the previous display.


For more information on
these applications, refer to
the "Peugeot Connect Media
Navigation (NG4 3D)" section.

For operation of the retractable
screen (opening, closing, ad-
justment of the position, etc.),
refer to the "Access to the retractable
screen" section.



The screen also displays hybrid
system information. For details of
the information displayed, refer
to the "Hybrid System" section.



For safety reasons, confi gu-
ration of the multifunction
screen by the driver must only
be done when stationary.

M
U
66

"SETUP" menu




)
Press the "SETUP"
button for access
to the "SETUP"
menu. This allows you
to select from the following functions:


- "Languages and voice functions",

- "Date and time",

- "Display",

- "Units",

- "System".



Language and voice functions
This menu allows you to:


- select the language used by the
screen (Deutsch, English, Espanol,
Français, Italiano, Nederlands,
Polski, Portugues, Türkçe * ),

- select the voice recognition param-
eters (activation/deactivation, advice
on use, personal voice programming,
etc.),

-
set the volume of the voice synthesiser.




Date and time
This menu allows you to set the date
and time, the format of the date and the
format of the time.

Principle of GPS synchronisation (GMT).


- Confi rm the selection "Synchronise
with GPS", the time is then aligned
with GMT universal time, the date is
also set.

- using the navigator, move the cursor
onto the hours fi eld and press OK
.

- You can then adjust the time to the
time zone of your choice, using the
rotating ring.
Please note that in the event of a
change of summer/winter time, the
time zone must be changed again
manually.


Display
This menu allows you to set the bright-
ness of the screen, the screen colour
scheme and the colour of the map (day/
night or auto mode).

Units
This menu allows you to select the units:
temperature (°C or °F) and distance
(miles or km).

For safety reasons, confi guration
of the multifunction screen by the
driver must only be done when
stationary.

*
According to country of sale.
System parameters
This menu allows you to restore the factory
confi guration, display the software version
and activate scrolling text.

M
U
67
Access to the retractable screen
This screen is opened and stored auto-
matically.
However, you can also open it, store it
and adjust it using the various manual
controls:


- opening or storing by means of
control A
,

- angle adjustments by means of
control B
.
It is also fi tted with safety auto-reverse
protection.

Opening the screen


)
With the screen stored, press con-
trol A
to open it.
The screen opens automatically when
the ignition is switched on, when the au-
dio and telematics system is switched
on, when an outgoing telephone call
is made, when a voice command is
given and when a warning message
linked with the STOP warning lamp is
received.
Closing the screen


)
With the screen open, press control A

to store it.
The screen is stored automatically when
the ignition is switched off, after approxi-
mately three seconds, if the audio and
telematics system is off.
If you wish the screen to open
or close automatically when
the audio and telematics sys-
tem is switched on or off, the screen
must not be closed when the audio
and telematics system is operating. When the screen is open, you can ad-
just it precisely in different ways:


)
press the corresponding part of con-
trol B
to move the screen towards
you or towards the windscreen,
or


)
push or pull the screen gently by
hand.

Adjusting the position of the screen

Safety auto-reverse
If the screen meets an obstacle as it
opens or closes, the movement stops
immediately and is reversed by a few
millimetres.
After clearing the obstacle, issue the
command required again.

Storing the position of the screen
The system has four pre-set positions
in its memory.
Each time the screen is closed, the
system stores the last position of the
screen.
Each time the screen is re-opened, the
system returns the screen to the pre-set
position closest to that stored.


If you close the screen during
operation of the audio and tele-
matics system, it will re-open au-
tomatically when an outgoing telephone
call is made, when a voice command is
given or when a warning message linked
with the STOP warning lamp is received.

M
U
68

Monochrome screen C


Instrument panel screen with Peugeot
Connect Media Navigation (NG4 3D)
TRIP COMPUTER
System which provides current information
concerning the trip (range, consumption…).
Depending on your vehicle's
equipment, the trip computer
information appears in the
multifunction screen or in the instru-
ment panel screen.
Information displays


)
Press the button, located at the end
of the wiper stalk
, to display the
various trip computer tabs in suc-
cession.


With the instrument panel screen
(Peugeot
Connect Media Navigation (NG4 3D))



)
This navigator, associated with the
Peugeot Connect Media Navigation
(NG4 3D), also allows the various
trip computer tabs to be displayed
in the instrument panel screen, by
pressing the up and down arrows.