Peugeot 307 SW 2007.5 Manual Online

72
ACCESS
This enables the tailgate to be
unlocked in the event of a central
locking fault.
- Fold back the rear seats to gain access to the lock from inside the
boot,
- Insert a small screwdriver into hole A of the lock to unlock the
tailgate. Safety auto-reverse
At the end of its travel, if the shutter
encounters an obstacle to closing, it
stops and moves back slightly.
Your vehicle is i tted with a tinted glass
panoramic roof which increases the
light and visibility in the passenger
compartment. Its electric concealing
shutter improves temperature conditions.

To open: press part A of the switch.

To close: press part B of the switch.

Manually: press the switch without
going past the point of resistance; the
shutter stops as soon as the switch is
released.

Automatically: press the switch
beyond the point of resistance;
one press fully opens or closes the
shutter. Press the switch again to
stop the shutter. Notes
If the shutter’s power supply is cut off,
while it is moving or immediately after
it has stopped, you must reinitialise
the safety auto-reverse:
- press section
B of the switch
until the shutter is completely
closed (closing in stages of a few
centimetres).
In the event of unwanted opening
of the shutter on closing, and
immediately after the shutter has
stopped:
- press section A of the switch until
the shutter is fully open,
- release section A and immediately
afterwards press section B of the
switch until the shutter is fully
closed (closing in stages of a few
centimetres).

The safety auto-reverse function is
not active during these operations.
PANORAMIC ROOF Tailgate release

72
ACCESS
This enables the tailgate to be
unlocked in the event of a central
locking fault.
- Fold back the rear seats to gain access to the lock from inside the
boot,
- Insert a small screwdriver into hole A of the lock to unlock the
tailgate. Safety auto-reverse
At the end of its travel, if the shutter
encounters an obstacle to closing, it
stops and moves back slightly.
Your vehicle is i tted with a tinted glass
panoramic roof which increases the
light and visibility in the passenger
compartment. Its electric concealing
shutter improves temperature conditions.

To open: press part A of the switch.

To close: press part B of the switch.

Manually: press the switch without
going past the point of resistance; the
shutter stops as soon as the switch is
released.

Automatically: press the switch
beyond the point of resistance;
one press fully opens or closes the
shutter. Press the switch again to
stop the shutter. Notes
If the shutter’s power supply is cut off,
while it is moving or immediately after
it has stopped, you must reinitialise
the safety auto-reverse:
- press section
B of the switch
until the shutter is completely
closed (closing in stages of a few
centimetres).
In the event of unwanted opening
of the shutter on closing, and
immediately after the shutter has
stopped:
- press section A of the switch until
the shutter is fully open,
- release section A and immediately
afterwards press section B of the
switch until the shutter is fully
closed (closing in stages of a few
centimetres).

The safety auto-reverse function is
not active during these operations.
PANORAMIC ROOF Tailgate release

73
ACCESS
The engine must be switched off
when i lling with fuel.

 Open the fuel i ller l ap.

 Insert the key then turn it to the
left.

 Remove the cap and hang it on
the hook located on the inside of
the l ap.
A label afi xed to the inside of the fuel
i ller l ap indicates which type of fuel
to use.
When you i ll your tank, do not
continue after the third cut-off of the
pump. This could cause your vehicle
to malfunction.

The capacity of the tank is
approximately 60 litres.

 After i lling the tank, lock the cap
and close the fuel i ller l ap.
Low fuel level
When the minimum
fuel level in the tank is
reached, this warning
light comes on on the
instrument panel.

You can still drive approximately
30 miles (50 km). Operating fault
With the ignition on, if the fuel gauge
needle remains in or returns to
the rest position (below zero), this
indicates a malfunction of the fuel
gauge.
Contact a PEUGEOT dealer. FILLING WITH FUEL 1.6 litre 16V BioFlex engine
Your BioFlex vehicle is an adaptable
vehicle. It has been designed to
run equally well on unleaded petrol
(RON 95 or RON 98) or ethanol (in
Europe, this is a mixture containing
85 % ethanol and 15 % unleaded
petrol, referred to as E85).
So, irrespective of the quantity of fuel
remaining in your tank and regardless
of the type of fuel (unleaded petrol,
E85 or a mixture of the two), you
can i ll your tank at any time with
unleaded petrol (RON 95 or RON 85)
or ethanol E85.
This vehicle will run on unleaded
petrol only without experiencing any
problems.
In wintry conditions, starting
the engine from cold may
sometimes prove difi cult.
During these very cold periods,
it is advisable to favour unleaded
petrol to guarantee optimum starting
conditions.

74
VISIBILITY
Front and rear lights (ring A)

 Place ring A in the required position.
Dipped/Main beam change

 Pull the stalk towards you. Vehicles i tted with front fog
lamps and a rear fog lamp (ring C)
Lights off
Side lights Dipped/main beam
headlamps Rear fog lamp Front fog lamps ( i rst rotation
of the ring forwards)
Front and rear fog
lamps (2nd rotation
of the ring forwards).

Note: to switch off
the rear fog lamp
and the front fog lamps, turn the ring
backwards twice in succession.
Vehicles i tted with a rear fog
lamp (ring B)
This operates with the dipped/main
beam headlamps.

Note: when the lights are switched off
automatically, the rear fog lamp and
the dipped headlamps will remain on.
Turn the ring backwards to switch
off the rear fog lamp. The dipped
headlamps will then be switched off. The front fog lamps operate with
the side lights and the dipped
headlamps.
Front fog lamps and rear fog
lamp

 Turn ring B or C forwards to switch
on and backwards to switch off.
The status is coni rmed by the
indicator light on the instrument
panel .
Lights on buzzer
With the ignition off and the automatic
switching on of the lights deactivated,
when the driver’s door is opened, a
buzzer sounds to warn you that you
have left your lights on.
In good or rainy weather,
both day and night, the front
fog lamps and the rear fog
lamp are dazzling and are
prohibited.
Do not forget to switch them off when
they are no longer needed.
LIGHTS STALK
The rear fog lamp will be
deactivated automatically
when towing or when a
bicycle carrier i tted with a
fog lamp is i tted.
Automatic switching
on of the lights

75
VISIBILITY
Automatic switching on of the
lights
Side lights and dipped beam head-
lamps switch on automatically if the
light is poor, or during operation of the
windscreen wipers. They switch off
as soon as the light becomes bright
enough or the windscreen wipers
stop.

Note: in foggy weather or in snow,
the brightness sensor can detect
sufi cient light. As a consequence, the
lights will not come on automatically.
Deactivation

 Turn ring A to a position other
than "AUTO" . Switching off is
accompanied by a message on
the multifunction display.

If the brightness sensor does not
function correctly, the lights come
on accompanied by the service
warning light, an audible signal and
a message on the multifunction dis-
play.
Contact a PEUGEOT dealer.
Manual "Follow-me-home" lighting

When the automatic switching on of
the lights function is deactivated , the
side lights and dipped headlamps re-
main on for the duration selected for the
automatic "follow-me-home" lighting.

If the vehicle is not i tted with the
automatic switching on of the lights
function , when you leave your vehicle,
the side lights and dipped headlamps
remain on for thirty seconds.
Direction indicators (l ashers)

Left: downwards.

Right: upwards.

Note: if you forget to cancel the di-
rection indicator, the volume of the
audible signal will increase, if you
are driving at a speed greater than
50 mph (80 km/h).
Automatic "Follow me home"
lighting
With the ignition off, when you leave
your vehicle with the automatic
switching on of the lights function
activated , the side lights and dipped
headlamps remain on for the selected
duration. Activation:

 switch off the engine,

 "l ash" the headlamps,

 get out of the vehicle and lock it.
Deactivation:

 "l ash" the headlamps again,

 get out of the vehicle and lock it.
To deactivate or activate
this function, go to the mul-
tifunction display coni gura-
tion menu.
The duration of the timed
period must also be set (15, 30,
60 seconds), via the multifunction
display coni guration menu, except
in the case of the monochrome
screen A for which it is pre-set.
Cancelling:

 "l ash" the headlamps,

 get out of the vehicle and lock it. Activation

 Turn ring A to the "AUTO"
position. The automatic lighting
is accompanied by a message on
the multifunction display.
Do not cover the brightness
sensor, coupled with the rain
sensor, located in the centre
of the windscreen, behind
the interior mirror. It is used for the
automatic switching on of the lights.

76
VISIBILITY
For vehicles i tted with halogen
bulbs, depending on the load in your
vehicle, adjusting the beam of your
headlamps is recommended.

0. 1 or 2 people in the front seats.

-. 3 people.

1. 5 or 7 people.

-. Intermediate setting.

2. 5 or 7 people + maximum
authorised load.

-. Intermediate setting.

3. Driver + maximum
authorised load.

Initial setting is position 0. On vehicles with xenon bulbs:

when stationary , the system auto-
matically corrects the height of the
beam, whatever the load of the vehi-
cle. The driver is then assured of hav-
ing optimum lighting and not causing a
nuisance to other road users.

In cases of malfunction ,
the service warning light
comes on on the instrument
panel, accompanied by an
audible signal and a mes-
sage on the multifunction display.
The system places your headlamps
to the low position.
Do not touch the xenon bulbs.
Contact a PEUGEOT dealer.
Daytime lights *
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
* According to country.
The instruments and controls
(instrument panel, multifunc-
tion display, air conditioning
control panel, ...) are only lit
on switching to the automatic switch-
ing on of the lights mode or when the
lights are switched on manually. This warning light comes
on on the instrument panel.
MANUAL ADJUSTMENT OF
THE HEADLAMPS
AUTOMATIC HEADLAMP
ADJUSTMENT

75
VISIBILITY
Automatic switching on of the
lights
Side lights and dipped beam head-
lamps switch on automatically if the
light is poor, or during operation of the
windscreen wipers. They switch off
as soon as the light becomes bright
enough or the windscreen wipers
stop.

Note: in foggy weather or in snow,
the brightness sensor can detect
sufi cient light. As a consequence, the
lights will not come on automatically.
Deactivation

 Turn ring A to a position other
than "AUTO" . Switching off is
accompanied by a message on
the multifunction display.

If the brightness sensor does not
function correctly, the lights come
on accompanied by the service
warning light, an audible signal and
a message on the multifunction dis-
play.
Contact a PEUGEOT dealer.
Manual "Follow-me-home" lighting

When the automatic switching on of
the lights function is deactivated , the
side lights and dipped headlamps re-
main on for the duration selected for the
automatic "follow-me-home" lighting.

If the vehicle is not i tted with the
automatic switching on of the lights
function , when you leave your vehicle,
the side lights and dipped headlamps
remain on for thirty seconds.
Direction indicators (l ashers)

Left: downwards.

Right: upwards.

Note: if you forget to cancel the di-
rection indicator, the volume of the
audible signal will increase, if you
are driving at a speed greater than
50 mph (80 km/h).
Automatic "Follow me home"
lighting
With the ignition off, when you leave
your vehicle with the automatic
switching on of the lights function
activated , the side lights and dipped
headlamps remain on for the selected
duration. Activation:

 switch off the engine,

 "l ash" the headlamps,

 get out of the vehicle and lock it.
Deactivation:

 "l ash" the headlamps again,

 get out of the vehicle and lock it.
To deactivate or activate
this function, go to the mul-
tifunction display coni gura-
tion menu.
The duration of the timed
period must also be set (15, 30,
60 seconds), via the multifunction
display coni guration menu, except
in the case of the monochrome
screen A for which it is pre-set.
Cancelling:

 "l ash" the headlamps,

 get out of the vehicle and lock it. Activation

 Turn ring A to the "AUTO"
position. The automatic lighting
is accompanied by a message on
the multifunction display.
Do not cover the brightness
sensor, coupled with the rain
sensor, located in the centre
of the windscreen, behind
the interior mirror. It is used for the
automatic switching on of the lights.

76
VISIBILITY
For vehicles i tted with halogen
bulbs, depending on the load in your
vehicle, adjusting the beam of your
headlamps is recommended.

0. 1 or 2 people in the front seats.

-. 3 people.

1. 5 or 7 people.

-. Intermediate setting.

2. 5 or 7 people + maximum
authorised load.

-. Intermediate setting.

3. Driver + maximum
authorised load.

Initial setting is position 0. On vehicles with xenon bulbs:

when stationary , the system auto-
matically corrects the height of the
beam, whatever the load of the vehi-
cle. The driver is then assured of hav-
ing optimum lighting and not causing a
nuisance to other road users.

In cases of malfunction ,
the service warning light
comes on on the instrument
panel, accompanied by an
audible signal and a mes-
sage on the multifunction display.
The system places your headlamps
to the low position.
Do not touch the xenon bulbs.
Contact a PEUGEOT dealer.
Daytime lights *
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
* According to country.
The instruments and controls
(instrument panel, multifunc-
tion display, air conditioning
control panel, ...) are only lit
on switching to the automatic switch-
ing on of the lights mode or when the
lights are switched on manually. This warning light comes
on on the instrument panel.
MANUAL ADJUSTMENT OF
THE HEADLAMPS
AUTOMATIC HEADLAMP
ADJUSTMENT

77
VISIBILITY
Special position of the front
windscreen wiper
In the minute following switching off
of the ignition, any action on the stalk
positions the wipers in the centre of
the windscreen.
This action enables you to position
the wiper blades for winter parking,
cleaning or replacement (See section
"Practical information - Changing a
wiper blade").
To park the wipers after this has
been done, switch on the ignition and
operate the stalk.
Windscreen and headlamp wash
Pull the windscreen wiper stalk
towards you. The windscreen wash
then the windscreen wipers operate
for a i xed period.
The headlamp wash is also activated,

if the headlamps are on.
Automatic windscreen wipers
In AUTO mode, the windscreen
wipers operate automatically and

adapt their speed to the intensity
of the rainfall .
Front windscreen wiper with
automatic wipe

2 Fast wipe (heavy rain).

1
Normal wipe (moderate rain).

I Intermittent wipe.

0 Off.

AUTO
 Automatic or single wipe
(press downwards).
In the I ntermittent position, the wiping
speed is in proportion to the speed of
the vehicle.
In AUTO mode, the wiping speed is in
proportion to the intensity of the rainfall.
The i rst press of the stalk downwards
activates the automatic wipe.
Subsequent presses trigger a single
wipe.
WINDSCREEN WIPER STALK
Front windscreen wiper with
intermittent wipe

2 Fast wipe (heavy rain).

1 Normal wipe (moderate rain).

I Intermittent wipe.

0 Off.

 Single wipe (press downwards).
In the I ntermittent position, the wiping
speed is in proportion to the vehicle
speed.

78
VISIBILITY
Do not cover the rain sensor
located on the windscreen
behind the interior mirror.
When using an automatic car
wash, switch off the ignition.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipe.
Activation
Activation of the function is
accompanied by a message on the
multifunction display.
Turn ring A to the i rst notch
for intermittent wiping.
When reverse gear is
engaged, if the windscreen
wipers are in operation, the
rear wiper will start wiping.
To activate or deactivate this
function, go to the multi-func-
tion display coni guration
menu.
If there is a signii cant ac-
cumulation of snow or ice and when
using a bicycle carrier on the tailgate,
deactivate the automatic rear wiping
by going to the multifunction display
coni guration menu.
Turn ring A past the i rst
notch; the windscreen wash
then the windscreen wiper
operate for a i xed period.
Deactivation
Deactivation of the function is
accompanied by a message on the
multifunction display.
The function is deactivated when the
windscreen wipers stalk is moved to
position
I , 1 or 2 .

In the event of malfunction of the
automatic windscreen wipers, the
windscreen wipers will operate in
intermittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Rear windscreen wash 1. Front courtesy light
In this position, the courtesy
light comes on automatically:
-
when the vehicle is unlocked, - when the key is removed from the ignition, - when a door is opened, - when the vehicle location function is used.
Permanently off.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- with the ignition off, 30 seconds
after the last door is closed.
COURTESY LIGHTS Rear windscreen wiper

The automatic windscreen
wipers function must be
reactivated if the ignition
has been switched off for
more than one minute, by pressing
the stalk downwards.