ESP Peugeot 307 SW Dag 2002.5 Owner's Guide

22-07-2002
Removing a seat Fold the corresponding seat.
Tilt the two red levers Funder the
seat to release the front feet.Lift it and carry it using the carrying handle G.
In the 3rd row, position the fixingpoint closers to obtain a flat boot
floor. Refitting a seat
In the 3rd row, first remove the floor fixing point closers using a screwdri-ver or a coin. Before positioning the 3rd row seats, move those of the 2nd row forward. Check that nothing is obstructing the floor fixing points thus pre-venting correct locking of the seatfeet. Carry the seat using the carrying handle
G.
Position the front feet in the securingpoints.
Locked Free Push control Dupwards to check
that the rear feet are free.
Tilt the folded seat backwards. The rear feet lock automatically, as do the two red levers
F.
Check that the seat is locked cor-
rectly. Lift the seat back, first releasing it by pulling the strap C.
To lock the additional seats, pressthe two levers E.
YOUR 307 SW IN DETAIL
92
Only lock the seat back on the cushion occasio-
nally, to avoid undue wearof the seat covers.
Avoid placing luggage on foldedseats. Never use the adjusting straps to remove, refit or carry a seat.

22-07-2002
''Isofix'' mountings
Available on the two side rear seats, the Isofix mountings allow for fittingof a special child seat for
PEUGEOT vehicles and sold by
PEUGEOT dealers. The locks incorporated in the child seat fit onto the Isofix mountings andensure safe, reliable and fast assem-
bly. The special approved child seat is
the Isofix KIDDY seat. It can be usedin the "rear facing" position when theside seats are recentred from birth to13 kg and in the "forwards facing"position from 9 to 18 kg. In the "forwards facing" position, the front seat must be in the mid-wayposition on the slide, with the seatback upright. The combined use of the Isofix mounting, the restraining cushion
and the seat belt is then compulsory.
The Isofix KIDDY seat can also be installed on a side seat in the 2nd
row, positioned in the 3rd row. In this
case, the Isofix KIDDY seat must bein the "rear facing" position, the bodysupported on the seat back of thecorresponding 2nd row seat.
YOUR 307 SW IN DETAIL
93
This seat can also be used on seats not fitted with Isofix mountings: inthis case it is compulsory to attach itto the vehicle's seat by means of thethree-point seat belt.
When the Isofix KIDDY seat is fit- ted in the "rear facing" positionon the front passenger seat, it isimperative that that passenger airbag be disarmed. Otherwise there is a risk the child could be seriously injured or evenkilled due to deployment of the airbag. Follow the instructions for fitting the child seat in the manufactu-rer's instruction booklet.

22-07-2002
YOUR 307 SW IN DETAIL
98
3rd row rear seat belts The 3rd row rear seats are fitted with two three-point inertia reel seatbelts.
To put on the seat belt, insert buckle C
then buckle Dinto their respective
stalks.
To remove the seat belt, proceed in
the reverse order, then move buckleD to the location Eprovided.
To be effective, a seat belt must be tightened asclose to the body as pos-sible.
If the seats are fitted with arm-rests, the lap section of the seatbelt must always pass under thearmrest. Do not invert the seat belt buckles as they will not carry out their
function fully. Depending on the nature and the seriousness of the impact, thepre-tensioners may be triggeredbefore and independently of trig-gering of the airbags. In all cases, the airbag warning light comes on. Following a collision, have the system checked by a PEUGEOT
dealer. The system has been designed to be fully operational for ten years.
For greater safety, have it chec- ked by a PEUGEOT dealer afterthis period.
2nd row rear centre seat belt The 2nd row rear centre seat has a three-point inertia reel seat beltincorporated in the centre of theroof. Pass buckle A, then buckle B, into
the strap guide working from the inside to the outside of the seat. Insert buckle Ainto its stalk (right),
then buckle Binto its stalk (left).
To remove the seat belt, proceed in
the reverse order, then move buckleB to the magnet of the roof fixing
point.

22-07-2002
WINDSCREEN WIPER STALK Stalk with intermittent wipe Front windscreen wiper2 Fast wipe (heavy rain).
1 Normal wipe (moderate rain).
I Intermittent wipe.
0 Off.
Single wipe (press downwards). Stalk with automatic wipeFront windscreen wiper
2 Fast wipe (heavy rain).
1 ormal wipe (moderate rain).
AUTO Automatic wipe.
0 Off.
Single wipe (press downwards). OperationIn position
1or 2, when the vehicle
stops, the windscreen wiper changes to a lower wiping speed, thenresumes its initial speed when thevehicle starts again. In the Intermittent position, the wiping speed is proportional to thespeed of the vehicle. In the AUTOposition, the wiping
speed is proportional to the heavi- ness of the rain. When the ignition has been swit- ched off for more than one minutewith the stalk in the wipe position,it is necesary to reactivate thisfunction. To do this, move the stalk
to any position, then move it back tothe required position.
Windscreen and headlamp wash Pull the windscreen wiper stalk towards you. The windscreen wash then the wind- screen wipers operate for a fixed
period. The windscreen wash andheadlamp wash operate simulta-neously for a few seconds, only if
the dipped beam or main beamheadlamps are on.
YOUR 307 SW IN DETAIL 111

22-07-2002
YOUR 307 SW IN DETAIL115
Trip computer function This function allows inputting of the distance to the destination (whenguidance is not activated; otherwisethe information is given by the navi-gation) and also changing of the
units (¡C or ¡F, km and litres or milesand gallons). Diagnostics This function tells you the warnings, the quantity of emergency fuel andthe GPS cover present at the timeconsulted. Note: these alerts have previously
been displayed in the form of mes- sages and/or warning lights on thecontrol unit. There are 6 categories of diagnostics:
- engine diagnostics (warnings lin- ked to the engine and gearbox etc....),
- brake diagnostics,
- suspension diagnostics (warnings linked to the suspension, ESP etc....),
- wheel diagnostics (warnings linked to tyres),
- doors and windows diagnostics,
- passenger compartment diagnos- tics. Distance to destination When guidance is not activated, this enables an approximate value to beentered to make all the trip computercalculations possible.
Specific features of the mono- chrome screen CT and thecolour screen DT General menu Press the
"MENU"button to access
the general menu.Select the icon "Trip computer"
using the knob, then validate to
access the "Trip computer" menu.
The ''trip computer'' menu offers various choices:
- Trip computer configuration,
- Diagnostics.
"Trip computer" context menu The context menu associated with the "Trip Computer" application
appears as a superimposed display
when the Trip Computer is the appli-cation currently being used in the
main screen window. Briefly press the continuous applica-
tion "Trip computer" button to selectone of the following functions:
- warnings log,
- Distance to destination.

22-07-2002
ELECTRIC WINDOWS
1 - Driver's electric window switch.
2 - Passenger's electric windowswitch.
3 - Rear right electric window switch.
4 - Rear left electric window switch.
5 - Disarming of the rear electric window switches (child lock). You have two options: Manual operation:
press or pull switch 1gently. The
window stops as soon as the switch is released.
Automatic operation: press or pull switch 1fully. One
touch completely opens or closes
the window.
Safety auto-reverse When the window rises and meets an obstacle, it stops and lowersagain. Notes:
- in the case of frost, if the window will not rise, press the switch until it
opens completely, then pull it againuntil it closes.
- following reconnection of the batte- ry, if the window will not rise, relea-se the switch and pull it again until
it closes completely. Hold the swit-ch for approximately one secondafter closing.
YOUR 307 SW IN DETAIL
116
EXTERIOR MIRRORS Electric rear view mirrors
Slide switch Ato the right or to
the left to select the correspon-
ding mirror.
Move knob Bin all four directions
to adjust.
Return switch Ato the centre
position.
When parked, the mirrors can be
folded back manually, electrically bypulling knob Arearwards or automa-
tically when locking the vehicle. The exterior mirrors are unfolded by switching on the ignition to thesecond notch or to the ON position. Note : the function that controls fol-
ding of the mirrors when locking the vehicle can be disarmed. Contact a
PEUGEOT dealer.

22-07-2002
ELECTRIC WINDOWS
1 - Driver's electric window switch.
2 - Passenger's electric windowswitch.
3 - Rear right electric window switch.
4 - Rear left electric window switch.
5 - Disarming of the rear electric window switches (child lock). You have two options: Manual operation:
press or pull switch 1gently. The
window stops as soon as the switch is released.
Automatic operation: press or pull switch 1fully. One
touch completely opens or closes
the window.
Safety auto-reverse When the window rises and meets an obstacle, it stops and lowersagain. Notes:
- in the case of frost, if the window will not rise, press the switch until it
opens completely, then pull it againuntil it closes.
- following reconnection of the batte- ry, if the window will not rise, relea-se the switch and pull it again until
it closes completely. Hold the swit-ch for approximately one secondafter closing.
YOUR 307 SW IN DETAIL
116
EXTERIOR MIRRORS Electric rear view mirrors
Slide switch Ato the right or to
the left to select the correspon-
ding mirror.
Move knob Bin all four directions
to adjust.
Return switch Ato the centre
position.
When parked, the mirrors can be
folded back manually, electrically bypulling knob Arearwards or automa-
tically when locking the vehicle. The exterior mirrors are unfolded by switching on the ignition to thesecond notch or to the ON position. Note : the function that controls fol-
ding of the mirrors when locking the vehicle can be disarmed. Contact a
PEUGEOT dealer.

22-07-2002
YOUR 307 SW IN DETAIL125
BOOT LAYOUT
1 - Grab handles and coat hooks
2 - High load retaining net fastenings The high load retaining net can be fitted in the 2nd or
3rd row. Open the covers of the corresponding upper faste- nings. Fit the ends of the metal bar in these fastenings.Secure the two opaque material strap hooks in the sto-
wing rings on the floor. The rings are located directly below the corresponding upper fastenings. Pull the two straps taut.Secure the two hooks on the elastic parts of the opaque material in these rings. Note: the net must be positioned so that the label can
be seen from the boot. This ensures that the central
seat belt is routed correctly.
3 - 12V Socket for accessories This is a 12 volt socket (lighter type), installed on thetonneau left support.
It is supplied with the ignition off.
4 - Rear armrests with grab handle
5 - Storage nets One of them contains the luggage retaining net.
6 - Tonneau To install it:
Ð position one end of the tonneau roller in the 2nd row, Ð compress the opposite end of the roller and position
it,
Ð release it to allow it to engage,
Ð unroll the tonneau as far as the boot pillars,
Ð insert the tonneau guides in the rails in the pillars. To remove it:
Ð remove the tonneau guides from the pillar rails,
Ð return the tonneau into its roller,
Ð compress it and remove it from its support at the 2nd row,
To store it, pull it back and place it with the two storage nets, already lowered. Note: the roller has two hooks for securing the lugga-
ge retaining net depending on where it is installed.
7 - Luggage retaining net Secure the net's seven hooks in the stowing rings and
the fastenings on the floor.
8 - Luggage retaining net fastenings ("hammock" version) in the tailgate Fold the net in two. Secure the two centre hooks in the stowing rings on the
floor. Secure the net's remaining four hooks on the boot pillars.
See configuration of the nets (next page)

22-07-2002
S: sport programme.


: snow programme.
P ark: to immobilise the vehicle or start the engine ,
with the handbrake on or off.
R everse: to reverse (select this function with the
vehicle stationary, engine at idle). N eutral: to start the engine and to park, with the hand-
brake on. Note: if function Nis engaged inadvertently while dri-
ving, allow the engine to return to idle before engaging function Dto accelerate.
D rive : for driving in automatic mode.
M anual: for driving in manual mode.
YOUR 307 SW IN DETAIL 127
Moving Off
With the engine running, to move off from position P:
it is essential to press the
brake pedal to exit position P,
select function R, D or M, then
gradually release the pressureon the brake pedal; the vehicle
moves off immediately.
You can also move off from position N:
release the handbrake, with yourfoot on the brake,
select function R, D or M, then
gradually release the pressureon the brake pedal; the vehicle
moves off immediately.
WARNING When the engine is at idle, brakes not applied, if function R, D or Mis
selected the vehicle moves evenwithout the accelerator being pres-sed.For this reason, do not leave
children unsupervised inside thevehicle, with the engine running. When maintenance operations need to be carried out with the engine run-ning, apply the handbrake and selectposition P.
"PORSCHE TIPTRONIC SYSTEM" AUTOMATIC GEARBOX The four speed automatic gearbox offers a choice between the comfort of inte-
gral automatic operation , enhanced by a sport and a snow programme, or the
pleasure of manual gear changing.
Gear selection gate Move the lever in the gate to select a function. Once the function is selected, the corresponding indicator light appears on
the instrument panel display.

22-07-2002
TRACTION CONTROL (ASR)
AND DYNAMIC STABILITY
CONTROL (ESP) These systems are linked and com-
plement the ABS.
The ASR system optimises drive to prevent the wheels skidding, byacting on the brakes of the drivewheels and on the engine. It alsoallows the directional stability of thevehicle to be improved on accelera-tion. If there is a variation between the tra- jectory followed by the vehicle and
that required by the driver, the ESPsystem automatically acts on theengine and the brake of one or morewheels, in order to put the vehicleback on course. Operating checkWhen a malfunction of the system occurs, the indicatorlight comes on, accompa-nied by an audible signaland the message
"ESP/ASR not operational" on the
multi-function display.
Contact a PEUGEOT dealer to have the system checked.
YOUR 307 SW IN DETAIL
130
The ESP system offers increased safety duringnormal driving, but shouldnot incite the driver totake risks or to drive at
high speed. The operation of the system is ensured to the extent to which therecommendations of the manufac-turer regarding the wheels (tyresand wheel rims), the braking com-ponents, the electronic compo-nents and the assembly and repairprocedures within the PEUGEOTnetwork are observed. After an impact, have the system
checked by a PEUGEOT dealer.
EMERGENCY BRAKING
ASSISTANCE SYSTEM
In an emergency, this system enables the optimum braking
pressure to be reached more quickly,thus reducing the stopping distance. It is triggered according to the speed
of activation of the brake pedal. The
effect of this is a reduction in theresistance of the pedal and an
increase in braking efficiency.