Peugeot 308 SW BL 2009.5 Owner's Manual

11
i
177
PRACTICAL INFORMATION
After changing a wheel
To store the punctured wheel in the
boot correctly, fi rst remove the cen-
tral cover.
When using the "space-saver" type
spare wheel, do not exceed 50 mph
(80 km/h).
Have the tightening of the bolts and
the pressure of the spare wheel
checked by a PEUGEOT dealer
without delay.
Have the punctured wheel repaired
and replace it on the vehicle as
soon as possible.
Fitting the wheel
List of operations

 Put the wheel in place on the hub.

 Screw in the bolts by hand to the
stop.

 Pre-tighten the security bolt using
the wheelbrace 1 fi tted with the
security socket 3 .

 Pre-tighten the other bolts using the
wheelbrace 1 only.

 Lower the vehicle fully.

 Fold the jack 2 and detach it.

 Tighten the security bolt using the
wheelbrace 1 fi tted with the security
socket 3 .

 Tighten the other bolts using the
wheelbrace 1 only.

 Store the tools in the box.

11
!
!
!
178
PRACTICAL INFORMATION Risk of electrocution
Xenon bulbs (D1S-35W) must be
replaced by a PEUGEOT dealer.
CHANGING A BULB
Procedure for replacing a faulty bulb
with a new bulb without the use of
tools. Model with halogen headlamps

1. Direction indicators
(PY
21W
amber).

2. Dipped
beam
headlamps
(H7

-

55W).

3. Main beam headlamps
(H1

-

55W).

4. Daytime
running lamps
/

sidelamps
(P 21/
5W
).

5. Foglamps
(H8

-

35W).
1. Direction indicators
(PY 21W SV silver).

2. Directional dipped/main beam
headlamps (D1S-35W).

3. Additional main beam headlamps
(H1-55W).

4. Daytime running lamps/
sidelamps (P 21/5W).

5. Foglamps (H8-35W).
Model with xenon and dir
ectional
headlamps
The headlamps are fi tted with poly-
carbonate glass with a protective
coating:

 do not clean them using a dry
or abrasive cloth, nor with a
detergent or solvent product,

 use a sponge and soapy water,

 when using a high pressure
washer on persistent marks,
do not direct at the lamps or
their outlines for too long, so as
not to damage their protective
coating and seals.

 Do not touch the bulb directly
with your fi ngers, use lint-free
cloths.
Changing a halogen bulb should
only be done after the headlamp
has been switched off for a few
minutes (risk of serious burns).
It is imperative to use only anti-ul-
traviolet (UV) type bulbs in order
not to damage the headlamp. Front lamps

11
i
!
179
PRACTICAL INFORMATION
Changing main beam headlamp
bulbs

 Remove the protective cover by
pulling on the tab.

 Disconnect the bulb connector.

 Compress the springs to release the
bulb.

 Remove the bulb and change it
To refi t, carry out these operations in re-
verse order.
Changing daytime running lamp/
sidelamp bulbs

 Remove the protective cover by
pulling on the tab.

 Disconnect the bulb connector.

 Turn the bulb holder a quarter of a
turn and extract it.

 Pull the bulb and change it.
To refi t, carry out these operations in re-
verse order.
Changing dipped beam headlamp
bulbs

 Remove the protective cover by
pulling on the tab.

 Disconnect the bulb connector.

 Spread the springs to release the
bulb.

 Extract the bulb and change it.
To refi t, carry out these operations in re-
verse order.
Changing direction indicator bulbs

 Turn the bulb holder a quarter of a
turn and extract it.

 Pull the bulb and change it.
To refi t, carry out these operations in re-
verse order.
Amber or silver coloured bulbs,
such as the direction indicators,
must be replaced with bulbs of
identical specifi cations and colour.
When refi tting, close the protective
cover carefully to assure the seal-
ing of the headlamp.

11
180
PRACTICAL INFORMATION Changing foglamp bulbs

 Insert a screwdriver towards the
centre of the repeater between the
repeater and the base of the mirror.

 Tilt the screwdriver to extract the
repeater and remove it.

 Disconnect the repeater connector.
To refi t, carry out these operations in re-
verse order.
Contact a PEUGEOT dealer to obtain
replacement repeaters.
Changing integrated direction
indicator side repeaters
To replace these bulbs consult a
PEUGEOT dealer.

11
i
181
PRACTICAL INFORMATION
Rear lamps

1. Brake
lamps/
sidelamps

(
P21
/
5W
).

2. Sidelamps
(
P21
/
5W
).

3. Foglamp,
right-hand side (P21W).
Reversing lamp,
left-hand side
(P21W).

4. Direction indicators (
P21W
). Changing bulbs
These fi ve bulbs are changed from out-
side the boot:

 remove the two lamp fi xing nuts,

 extract the lamp carefully from the
outside,

 disconnect the lamp connector,

 press the four tabs and remove the
bulb holder,

 turn the bulb a quarter of a turn and
change it.
To refi t, carry out these operations in re-
verse order.
If the vehicle is fi tted with the JBL
audio system, on the right-hand
side, fi rst remove the three fi xing
bolts, then move the box.
 on the right-hand side; remove the
access fl ap,

 on the left-hand side; turn the fi xing
bolt a quarter of a turn and remove
the storage box cover,

 unclip the storage box,

11
182
PRACTICAL INFORMATION
Changing third brake lamp bulbs
(4 bulbs W5W)

 Unclip the tailgate upper trim from
left to right.

 Unscrew the two lamp fi xing nuts A .

 Unclip the lamp's central pin.

 Extract the lamp from the outside.

 Disconnect the bulb holder connector
and the wash-wipe pipe.

 Unclip the bulb holder from the lamp
by pressing on the two tabs B .

 Pull the bulb and change it.
To refi t, carry out these operations in re-
verse order.
Do not apply force to the lamp when
tightening the nuts. Changing the number plate lamp
bulbs (W5W)

 Insert a thin screwdriver into one of
the outer holes of the lens.

 Push it outwards to unclip.

 Remove the lens.

 Pull the bulb and change it.

11
183
PRACTICAL INFORMATION
Rear lamps

1. Brake
lamps/
sidelamps

(
P21
/
5W
).

2. Sidelamps
(
P21
/
5W
).

3. Foglamp,
right-hand side (P21W)
Reversing lamp,
left-hand side
(P21W)
.

4. Direction indicators (
P21W
) Changing bulbs
These fi ve bulbs are changed from out-
side the boot:

 unclip the lamp connector,

 separate the fi ve tabs and remove
the bulb holder,

 turn the bulb a quarter of a turn and
change it.

 open the boot,

 unscrew the two lamp fi xing bolts,

 extract the lamp carefully pulling
it from the bottom and pivoting it
towards the outside,
To refi t, carry out these operations in re-
verse order.
Take care to engage the lamp in its
guides keeping it in line with the vehicle.

11
184
PRACTICAL INFORMATION
Changing the number plate lamp
bulbs (W5W)

 Insert a thin screwdriver into one of
the outer holes of the lens.

 Push it outwards to unclip.

 Remove the lens.

 Pull the bulb and change it. Changing the third brake lamp
(SW - 4 bulbs W5W)

 Remove the two lamp fi xing nuts A .

 Take out the lamp from the outside.

 Disconnect the connector and the
screenwash pipe from the lamp.

 Turn the bulb holder corresponding
to the faulty bulb a quarter of a turn.

 Pull the bulb and change it.
To refi t, carry out these operations in re-
verse order.
Do not force the lamp when tightening
the nuts. Changing the third brake lamp
(SW - diodes)
On the versions with opening rear
screen, for the replacement of this type
of diode lamp, contact a PEUGEOT
dealer.

11
!
i
185
PRACTICAL INFORMATION PEUGEOT will not accept
responsibility for the cost incurred
in repairing your vehicle or for
rectifying malfunctions resulting
from the installation of accessories
not supplied and not recommended
by PEUGEOT and not installed in
accordance with its instructions,
in particular when the combined
consumption of all of the additional
equipment connected exceeds
10 milliamperes.
Installing electrical accessories
Your vehicle’s electrical system is
designed to operate with standard
or optional equipment.
Before installing other electri-
cal equipment or accessories on
your vehicle, contact a PEUGEOT
dealer.
CHANGING A FUSE
Access to the tools
The extraction pliers and the spare fus-
es are installed on the back of the dash-
board fusebox cover.
For access to them:

 open the glove box lid,

 push the opening guide to the left to
open to beyond the fi rst notch,

 open the glove box lid fully,

 turn the screw a quarter of a turn to
the left,

 unclip the fusebox cover by pulling
at the top right,

 remove the cover completely,

 remove the pliers. Changing a fuse
Before changing a fuse, the cause of
the failure must be identifi ed and recti-
fi ed.

 Identify the faulty fuse by checking
the condition of its fi lament.

 Use the special pliers to extract the
fuse from its housing.

 Always replace the faulty fuse with a
fuse of the same rating.

 Check the correspondence between
the number etched on the box, the
rating etched on the fuse and the
tables below.
Correct Incorrect

11PRACTICAL INFORMATION
Fascia fuses
The fuse box is placed in the lower
dashboard, left-hand side, inside the
glove box.
Access to the fuses

 refer to the paragraph "Access to
the tools". Fuse tables

Fuse N° Rating Functions

F1 15 A Rear wiper.

F2 30 A Locking and deadlocking earth.

F3 5 A Airbags and pretensioners control unit.

F4 10 A Clutch pedal and dual-function brake switches,
electrochromatic rear view mirror, air conditioning,
steering wheel angle sensor, automatic gearbox,
switching and protection unit.

F5 30 A Front one-touch electric windows, folding mirrors
supply, panoramic sunroof blind.

F6 30 A Rear one-touch electric windows, trailer fusebox.

F7 5 A Front and rear courtesy lamps, map reading lamps,
rear reading lampd, sun visor illumination, glove box
illumination, torch.

F8 20 A Audio equipment, audio/telephone, CD changer,
multifunction screen, tyre under-infl ation detection.

F9 30 A Front 12 V socket.

F10 15 A Steering mounted controls, alarm siren, alarm cont
rol
unit.

F11 15 A Low current ignition switch.