Peugeot 407 2009 Manual Online

Page 81 of 250

4ACCESS
72
FILLING WITH FUEL
The ignition must be switched
off and the vehicle must be un-
locked when fi lling with fuel. When this warning light comes
on in certain driving conditions
and depending on the engine,
the distance which can be
travelled with the fuel remaining may
be less than 30 miles (50 kilometres).
Note: should you run out of fuel, you
must add at least 6 litres.
Operating fault
A fuel gauge fault is indicated by the
fuel level indicator needle returning to
zero.
Consult a PEUGEOT dealer.
Fuel warning
A label affi xed to the inside of the fuel
fi ller fl ap indicates which type of fuel
to use.
When you fi ll your tank, do not con-
tinue after the third cut-off of the pump.
This could cause your vehicle to mal-
function.
The capacity of the tank is approxi-
mately 67 litres.

 After fi lling the tank, screw on the
cap and close the fuel fi ller fl ap.

 Open the fuel fi ller fl ap.

 Turn the cap to the left.

 Remove the cap and hang the end
on the hook located on the inside
of the fl ap. BioFlex engine
A Flex vehicle has been designed to
run on unleaded petrol (RON 95 or
RON 98) or ethanol (this is a mixture
containing 85 % ethanol and 15 % un-
leaded petrol, called E85).
So, regardless of the quantity of fuel
remaining in your tank and irrespec-
tive of its type (RON 95/RON 98, E85
or a mixture of the two), you can fi ll
your tank at any time with unleaded
petrol (RON 95 or RON 98) or ethanol
(E85).
There is no problem driving on unleaded
petrol only with this vehicle.
In winter conditions, starting the
engine from cold may some-
times prove diffi cult. During
these very cold periods you
are advised to favour unleaded petrol to
guarantee optimum starting conditions.

Page 82 of 250

5
73
LIGHTS
Lights on
With the ignition off, on opening the
driver's door a buzzer sounds to indi-
cate that you have left your lights on
although you are leaving the vehicle.

 Switch the lights off. Direction indicators
(fl ashers)
Dipped/main beam change

 Pull the stalk fully towards you. Front and rear fog lamps
(ring B)

 Turn ring B forwards to switch on
and rearwards to switch off. The
status is confi rmed by the light on
the instrument panel.
Front fog lamps (one press)

Left: downwards. The
direction arrow indicator
light fl ashes on the instru-
ment panel.

Right: upwards. The
direction arrow indicator
light fl ashes on the instru-
ment panel.
If you forget to return the
direction indicator to its normal
position, the volume of the
audible signal will increase, if
you are driving at a speed greater than
40 mph (60 km/h) or if the control is
maintained for more than 20 seconds.
These operate with the side lights and
the dipped or main beam headlamps.
Rear fog lamps (two presses)
These operate when the front fog
lamps are already on.
Front and rear lights (ring A)


Turn ring A to the position required.
Automatic switching on of
the lights,
Lights off,
Side lights,
Dipped/main beam
headlamps.

Model without AUTO lighting

Model with AUTO lighting

Page 83 of 250

5
74
Automatic switching on of the lights
The dipped beam headlamps switch
on automatically if the light is poor and
when the windscreen wipers operate
continuously. They switch off when
the light is bright enough or the wind-
screen wipers stop.
Warning: in foggy weather or in snow,
the brightness sensor can detect suf-
fi cient light. The lights will not come on
automatically.
If necessary, you must switch the
dipped headlamps on manually. Activation Manual "Follow-me-home"
lighting
When you leave your vehicle, the side
lights and dipped headlamps can be
left on for a few seconds.
When the function is activated,
the indicator light comes on on the
5-dial instrument panel display.
To disarm or activate the
function, pass via the
" P e r s o n a l i s a t i o n - c o n -
fi guration" menu on your
multifunction display.
For safety reasons, activation/
deactivation of the "Automatic
switching on of the lights"
function via the menu must be
carried out when stationary. To deactivate or activate the
"Automatic follow-me-home
lighting" function, pass via the

"Personalisation-confi gu-
ration" menu on your multi-
function screen.
The duration of timing can be
set via the "Personalisation-
confi guration" menu of your
multifunction display.
Automatic "Follow-me-home"
lighting
When you leave your vehicle
with the
automatic switching on of the lights
activated, the side lights and dipped
headlamps remain on for the duration
selected after the ignition is switched
off.
Disarming
When the function is disarmed,
the indicator light comes on on the
5-dial instrument panel display.
Do not cover the sunshine/
brightness sensor, located in
the centre of the windscreen.
It is used to regulate the air
conditioning and for the automatic
switching on of the lights.

If the sunshine/brightness sensor
does not function correctly, the side
lights and dipped headlamps come on.
Consult a PEUGEOT dealer. Activation:

 switch off the engine,

 "fl ash" the headlamps,

 get out of the vehicle and lock it.

Page 84 of 250

5
74
Automatic switching on of the lights
The dipped beam headlamps switch
on automatically if the light is poor and
when the windscreen wipers operate
continuously. They switch off when
the light is bright enough or the wind-
screen wipers stop.
Warning: in foggy weather or in snow,
the brightness sensor can detect suf-
fi cient light. The lights will not come on
automatically.
If necessary, you must switch the
dipped headlamps on manually. Activation Manual "Follow-me-home"
lighting
When you leave your vehicle, the side
lights and dipped headlamps can be
left on for a few seconds.
When the function is activated,
the indicator light comes on on the
5-dial instrument panel display.
To disarm or activate the
function, pass via the
" P e r s o n a l i s a t i o n - c o n -
fi guration" menu on your
multifunction display.
For safety reasons, activation/
deactivation of the "Automatic
switching on of the lights"
function via the menu must be
carried out when stationary. To deactivate or activate the
"Automatic follow-me-home
lighting" function, pass via the

"Personalisation-confi gu-
ration" menu on your multi-
function screen.
The duration of timing can be
set via the "Personalisation-
confi guration" menu of your
multifunction display.
Automatic "Follow-me-home"
lighting
When you leave your vehicle
with the
automatic switching on of the lights
activated, the side lights and dipped
headlamps remain on for the duration
selected after the ignition is switched
off.
Disarming
When the function is disarmed,
the indicator light comes on on the
5-dial instrument panel display.
Do not cover the sunshine/
brightness sensor, located in
the centre of the windscreen.
It is used to regulate the air
conditioning and for the automatic
switching on of the lights.

If the sunshine/brightness sensor
does not function correctly, the side
lights and dipped headlamps come on.
Consult a PEUGEOT dealer. Activation:

 switch off the engine,

 "fl ash" the headlamps,

 get out of the vehicle and lock it.

Page 85 of 250

5
75
MANUAL ADJUSTMENT OF THE HEADLAMPS AUTOMATIC HEADLAMP ADJUSTMENT

In cases of malfunction, the
warning light comes on on the
instrument panel display, ac-
companied by an audible signal
and a message on the multifunction dis-
play. The system places your headlamps
to the low position.
Do not touch the xenon bulbs. Consult
a PEUGEOT dealer.
Daytime running lamps *
On vehicles which are equipped with
daytime running lamps, the dipped
headlamps come on when the vehicle
is started.
This indicator lamp comes
on on the instrument panel
screen.
The instruments and controls
(instrument panel, multifunc-
tion screen, air conditioning
control panel...) are only lit
on switching to the automatic lighting
mode or when the lights are switched
on manually.
* According to country.
For vehicles fi tted with halogen bulbs,
depending on the load in your vehicle,
adjusting the beam of your headlamps
is recommended.

0. 1 or 2 people in the front seats.

-. 3 people.

1. 5 people.

-. Intermediate adjustment

2. 5 people + maximum authorised
loads.

-. Intermediate adjustment

3. Driver + maximum authorised
loads.

Initial setting is position 0. On vehicles with xenon bulbs:
when
stationary with the ignition on , the
system automatically corrects the
height of the beam, whatever the
load of the vehicle. The driver is then
assured of having optimum lighting
and not causing a nuisance to other
road users.

Page 86 of 250

5
76
WINDSCREEN WIPER STALK
Windscreen wiper with intermittent
wipe Windscreen wiper with automatic
wipe

The windscreen wiping
must be reactivated if the
ignition has been switched off
for more than one minute.

2 Fast wipe (heavy rain).

1 Normal wipe (moderate rain).

l Intermittent wipe.

0 Off.

 Single wipe (press downwards).
In the Intermittent position, the wiping
speed is in proportion to the vehicle
speed.
2 Fast wipe (heavy rain).

1 Normal wipe (moderate rain).

AUTO Automatic wipe.

0 Off.

 Single wipe
(press downwards).
In the AUTO position, no action on
your part is necessary.
2 Fast wipe (heavy rain).

1 Normal wipe (moderate rain).

I Intermittent wipe.

0 Off.
Windscreen wiper with Intermittent
and automatic wipe

The windscreen wiping
must be reactivated if the
ignition has been switched off
for more than one minute. Automatic, then single wipe
(see following page).
In the AUTO position, no action on
your part is necessary.
In the Intermittent position, the wiping
speed is in proportion to the vehicle
speed.
In the AUTO position, no action on
your part is necessary.

Page 87 of 250

5
77
Automatic windscreen wipers
Activation REAR WIPER CONTROL(407 SW)
Disarming
Do not cover the rain sensor
located on the windscreen be-
hind the interior mirror.
When using an automatic car
wash to wash your vehicle, switch off
the ignition or check that the wiper
stalk is not in the automatic position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipe. Automatic rear wiper
If the windscreen wipers control is acti-
vated and you engage reverse gear,
the rear wiper operates in intermittent
mode.

Note: if a bicycle carrier is used,
deactivate this function by
going to the "personalisation-
confi guration" menu on the
multifunction display or install a
special bicycle carrier approved by
PEUGEOT .
Turn the ring to the fi rst notch for inter-
mittent wiping.

The control must be reactivated if
the ignition has been switched off.
To do this, move the control to any
position then return it to the required
position.
Move the control to position
0 then re-
turn it to the AUTO position.
An indicator light comes on on the
instrument panel display, accompanied
by a message on the multifunction
display.
In the AUTO position, the windscreen
wipers operate automatically and
adapt their speed to the intensity of
the rainfall.
Control with automatic wiping only
In the event of malfunction , the
windscreen wipers will operate in in-
termittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Control with Intermittent and automatic wiping
Manual operation of the wiper stalk in-
terrupts the AUTO position, the deac-
tivation indicator light comes on on the
instrument panel display, accompa-
nied by a message on the multifunc-
tion display. Manual operation of the wiper stalk by
moving the lever
A up and returning
it to position "0" interrupts the AUTO
position, the deactivation indicator light
comes on on the instrument panel dis-
play, accompanied by a message on
the multifunction display.

Page 88 of 250

5
78
Windscreen and headlamp wash
Pull the windscreen wiper stalk towards
you. The windscreen wash then the
windscreen wipers operate for a fi xed
period.
The headlamp wash is also activated,

if the headlamps are on .
When the minimum level of
the reservoir is reached, this
warning light comes on, ac-
companied by an audible
signal and a message on the
multi-function display.
Next time you stop, fi ll the screenwash/
headlamp wash reservoir.
The warning light comes on each time
the stalk is operated, until the reservoir
is fi lled. FRONT COURTESY LIGHT
The courtesy light can be deactivated
by pressing switch 1 with the door open.
The map reading lights are not affected
by this and may be switched on.

 To re-activate the lights, press the
switch, with the door open.
Screenwash/headlamp wash low

1. Courtesy light

2. Map reading lights
With the key in the ignition on or starting
position, operate the relevant switch.
The front courtesy light comes on
when the ignition key is removed, on
unlocking the vehicle or on opening
one of the doors.
It gradually goes off after the ignition
has been switched on or when the
vehicle is locked.

 Pressing switch 1 turns on the front
courtesy light.
Rear wash-wipe

Note: the rear wiper and rear
wash-wipe functions are de-
activated automatically when
the rear screen is opened.
Turn the ring beyond the fi rst notch,
the wash-wipe then the wiper operate
for a set period of time.

Page 89 of 250

5
77
Automatic windscreen wipers
Activation REAR WIPER CONTROL(407 SW)
Disarming
Do not cover the rain sensor
located on the windscreen be-
hind the interior mirror.
When using an automatic car
wash to wash your vehicle, switch off
the ignition or check that the wiper
stalk is not in the automatic position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipe. Automatic rear wiper
If the windscreen wipers control is acti-
vated and you engage reverse gear,
the rear wiper operates in intermittent
mode.

Note: if a bicycle carrier is used,
deactivate this function by
going to the "personalisation-
confi guration" menu on the
multifunction display or install a
special bicycle carrier approved by
PEUGEOT .
Turn the ring to the fi rst notch for inter-
mittent wiping.

The control must be reactivated if
the ignition has been switched off.
To do this, move the control to any
position then return it to the required
position.
Move the control to position
0 then re-
turn it to the AUTO position.
An indicator light comes on on the
instrument panel display, accompanied
by a message on the multifunction
display.
In the AUTO position, the windscreen
wipers operate automatically and
adapt their speed to the intensity of
the rainfall.
Control with automatic wiping only
In the event of malfunction , the
windscreen wipers will operate in in-
termittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Control with Intermittent and automatic wiping
Manual operation of the wiper stalk in-
terrupts the AUTO position, the deac-
tivation indicator light comes on on the
instrument panel display, accompa-
nied by a message on the multifunc-
tion display. Manual operation of the wiper stalk by
moving the lever
A up and returning
it to position "0" interrupts the AUTO
position, the deactivation indicator light
comes on on the instrument panel dis-
play, accompanied by a message on
the multifunction display.

Page 90 of 250

5
77
Automatic windscreen wipers
Activation REAR WIPER CONTROL(407 SW)
Disarming
Do not cover the rain sensor
located on the windscreen be-
hind the interior mirror.
When using an automatic car
wash to wash your vehicle, switch off
the ignition or check that the wiper
stalk is not in the automatic position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipe. Automatic rear wiper
If the windscreen wipers control is acti-
vated and you engage reverse gear,
the rear wiper operates in intermittent
mode.

Note: if a bicycle carrier is used,
deactivate this function by
going to the "personalisation-
confi guration" menu on the
multifunction display or install a
special bicycle carrier approved by
PEUGEOT .
Turn the ring to the fi rst notch for inter-
mittent wiping.

The control must be reactivated if
the ignition has been switched off.
To do this, move the control to any
position then return it to the required
position.
Move the control to position
0 then re-
turn it to the AUTO position.
An indicator light comes on on the
instrument panel display, accompanied
by a message on the multifunction
display.
In the AUTO position, the windscreen
wipers operate automatically and
adapt their speed to the intensity of
the rainfall.
Control with automatic wiping only
In the event of malfunction , the
windscreen wipers will operate in in-
termittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Control with Intermittent and automatic wiping
Manual operation of the wiper stalk in-
terrupts the AUTO position, the deac-
tivation indicator light comes on on the
instrument panel display, accompa-
nied by a message on the multifunc-
tion display. Manual operation of the wiper stalk by
moving the lever
A up and returning
it to position "0" interrupts the AUTO
position, the deactivation indicator light
comes on on the instrument panel dis-
play, accompanied by a message on
the multifunction display.

Page:   < prev 1-10 ... 41-50 51-60 61-70 71-80 81-90 91-100 101-110 111-120 121-130 ... 250 next >