spare wheel Peugeot 407 2010 Owner's Manual

8DRIVING
102
TYRE UNDER-INFLATION DETECTION
Sensors check the tyre pressure dur-
ing driving and trigger a warning in the
event of malfunction.
Defl ated tyre Instrument panel display warn-
ing lamp.
This is accompanied by the audible
signal and the message on the mul-
tifunction screen identifying the wheel
concerned.
If this warning lamp comes on, have
the tyre pressure checked as soon as
possible.
Puncture
This warning lamp, accompanied by
the audible signal and the message on
the multifunction screen identifying the
wheel concerned, is followed by illumi-
nation of the 'STOP' warning lamp. Stop as soon as it is safe to do so,
avoiding any sudden movement of the
steering wheel and the brakes.
Change the damaged wheel (punc-
tured or very defl ated tyre), and have
the tyre pressure checked as soon as
possible.
Sensor(s) not detected or faulty
Instrument panel screen warn-
ing lamp. All repairs and changing of
tyres on a wheel fi tted with this
system must be carried out by
a PEUGEOT dealer.
If, when changing a tyre, you install a
wheel which is not detected by your
vehicle, you must have the system re-
initialised by a PEUGEOT dealer.
The tyre under-infl ation detection sys-
tem is an aid to driving which does not
replace the need for the driver to be
vigilant or to drive responsibly.
This system does not eliminate the
need to have the tyre pressures
checked regularly (see the label on
the door pillar) to ensure that the op-
timum dynamic performance of the
vehicle is maintained and prevent pre-
mature wear of the tyres, particularly
in arduous driving conditions (heavy
load, high speed).
The tyre pressures must be checked
cold, at least once a month. Remem-
ber to check the pressure of the spare
wheel.
The tyre under-infl ation detection sys-
tem may experience temporary interfer-
ence due to electromagnetic emissions
on a frequency close to that used by the
system.

Note : this message is also
displayed when one of the
wheels is away from the ve-
hicle (being repaired) or when
one or more wheels without a sensor
are fi tted.
Instrument panel display warn-
ing lamp.
This is accompanied by the audible
signal and the message on the mul-
tifunction screen which indicates that
under-infl ation detection is absent
from one (or several) wheel(s) or that
there is a fault in the system.
Contact a PEUGEOT dealer to replace
the faulty sensor(s).

1010PRACTICAL INFORMATION
113
CHANGING A WHEEL
Tools available
The following tools are located in
the holder in the centre of the spare
wheel:

1. Wheelbrace.
For removal of the wheel trim and removal of the wheel securing
bolts.

2. Jack with integral handle.
For raising the vehicle.

3. Removable towing eye.
See corresponding section.

4. Bolt cover tool.
For removal of the bolt protectors (covers) on alloy wheels. Removal

 For vehicles with steel wheels, de-
tach the trim using the wheelbrace 1
pulling at the valve passage hole.

 For vehicles with alloy wheels, re-
move the covers using tool 4 .

 Loosen the wheel bolts.

 Take the jack from the tool kit.

 Place the jack 2 in one of the four
locations underneath the vehicle
(the nearest one to the wheel to be
changed).

 Extend the jack 2 until its base is in
contact with the ground.

 Unscrew the bolts and remove the
wheel.
Access to the spare wheel and
the jack in the boot

 Lift the fl oor using the grip. Secure
the grip behind the boot seal. Never go underneath a ve-
hicle which is supported only
by a jack.

 Park the vehicle on level, stable
and non-slippery ground.

 Apply the parking brake, switch off
the ignition and engage fi rst or re-
verse gear (position P for the auto-
matic gearbox).

1010PRACTICAL INFORMATION
114
Fitting a wheel

 Position the wheel.

 Tighten the bolts by hand.

 Partly tighten the bolts using the
wheelbrace.

 Fold the jack 2 and remove it.

 Fully tighten the bolts using the
wheelbrace 1 .

 For vehicles with steel wheels, re-
fi t the wheel trim starting by plac-
ing its notch facing the valve and
press with the palm of the hand.

 For vehicles with alloy wheels, refi t
the covers.


Put the tool holder back in position.
This helps to keep the boot fl oor in its
correct position, to prevent any de-
formation of the fl oor when loaded.

 Tighten the spare wheel securing
strap to prevent noise and for your
safety in the event of impact. Punctured tyre warning
lamp
Information on the instrument
panel:

Reminder: for your safety, always
change a wheel:
- on level, stable, non-slippery ground,
- with the parking brake applied,
- with fi rst or reverse gear engaged (position P for the automatic gear-
box),
- never go underneath a vehicle which is supported only by a jack.
Tyre under-infl ation detection
system warning lamp
These original equipment wheels are
fi tted with a pressure sensor (see
paragraph "Tyre under-infl ation detec-
tion"). The warning which detects the
removal or absence of a wheel fi tted
with the pressure sensor signals the
anomaly. Have the wheel repaired and
checked by a PEUGEOT dealer.
After changing the wheel:
- have the tightness of the bolts and
the tyre pressure of the spare wheel
checked as soon as possible.
- have the punctured wheel repaired and refi t it to the vehicle as soon as
possible.
- have the spare wheel checked and replace it in its boot recess.
Recommendations when using
the temporary spare wheel *
Your vehicle may be equipped with a
spare wheel with a different rim to that
of the standard wheel.
After use, replace it as soon as possible.
Follow the recommendations below
to avoid any alteration in vehicle han-
dling:
-
do not drive above 50 mph (80 km/h) ,

- do not fi t a wheel trim,
- drive carefully,
- check the infl ation pressure indicated on the label.
* According to version and country.

1010PRACTICAL INFORMATION
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool to remove the trims
before slackening the bolts. Fitting the spare wheel
If your vehicle is fi tted with a steel spare
wheel, when fi tting it, it is
normal when
tightening the bolts to notice that the
washers do not come into contact with
the rim. The spare wheel is secured by
the cone shape of each bolt.
VERY COLD CLIMATE SCREEN *
The very cold climate screen is a par-
tial removable cover which is clipped
onto the air intake grille to prevent the
accumulation of snow due to direct
splashes.
Once it has been fi tted on your vehicle,
it must be removed when the ambient
temperature rises above 10 °C again.
Consult a PEUGEOT dealer.
215/55 R17 tyres cannot be
fi tted with standard snow
chains, contact a PEUGEOT
dealer.
* According to country.
Special features of alloy
wheels
Security bolts
Your wheels are fi tted with security
bolts (one per wheel), placed under
chrome trims which must be removed
using the yellow tool, before the bolts
are unscrewed using the security bolt
socket and the wheelbrace 1 .
Fitting snow tyres
If you fi t snow tyres mounted on steel
wheels onto your vehicle, it is
essen-
tial to use special bolts available from
your PEUGEOT dealer.
This security bolt socket was
given to you on delivery of
your vehicle with the duplicate
keys. Make a careful note of
the code number engraved on the
head of the security bolt socket. This
will enable you to obtain a duplicate
security bolt socket from a PEUGEOT
dealer. You are advised to do the same
for the duplicate keys.

1010PRACTICAL INFORMATION
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool to remove the trims
before slackening the bolts. Fitting the spare wheel
If your vehicle is fi tted with a steel spare
wheel, when fi tting it, it is
normal when
tightening the bolts to notice that the
washers do not come into contact with
the rim. The spare wheel is secured by
the cone shape of each bolt.
VERY COLD CLIMATE SCREEN *
The very cold climate screen is a par-
tial removable cover which is clipped
onto the air intake grille to prevent the
accumulation of snow due to direct
splashes.
Once it has been fi tted on your vehicle,
it must be removed when the ambient
temperature rises above 10 °C again.
Consult a PEUGEOT dealer.
215/55 R17 tyres cannot be
fi tted with standard snow
chains, contact a PEUGEOT
dealer.
* According to country.
Special features of alloy
wheels
Security bolts
Your wheels are fi tted with security
bolts (one per wheel), placed under
chrome trims which must be removed
using the yellow tool, before the bolts
are unscrewed using the security bolt
socket and the wheelbrace 1 .
Fitting snow tyres
If you fi t snow tyres mounted on steel
wheels onto your vehicle, it is
essen-
tial to use special bolts available from
your PEUGEOT dealer.
This security bolt socket was
given to you on delivery of
your vehicle with the duplicate
keys. Make a careful note of
the code number engraved on the
head of the security bolt socket. This
will enable you to obtain a duplicate
security bolt socket from a PEUGEOT
dealer. You are advised to do the same
for the duplicate keys.

1010PRACTICAL INFORMATION
117
Integrated direction indicator side
repeaters CHANGING A REAR BULB (SALOON)
Third brake light:
Five W 5 W bulbs.

 Remove the plastic cover carefully
by unclipping it at the centre and
on either side, perpendicular to its
direction of engagement.

 Press on the two tabs located at
the rear, near the rear screen.

 Pull the red transparent cover out-
wards while maintaining the pressure
on the tabs.

 Change the faulty bulb.

 When refi tting, ensure that the
tabs of the red transparent cover
are engaged correctly and that the
upper trim has been put back in
place correctly.

 Refi t the lamp fi xing nuts inside
the boot using the towing eye, if
necessary. When refi tting, ensure
that the lamp unit is positioned and
fi xed correctly.

 Reconnect the electrical connector.

Number plate lamps : W5W.

 Remove the transparent cover us-
ing a screwdriver blade.

 Change the faulty bulb.

 Push the repeater forwards or
backwards and release it.

 Unclip the repeater and change it.
Repeaters can be obtained from
PEUGEOT dealers.
Amber coloured bulbs (direction indi-
cators and side repeaters), must be
replaced with bulbs of identical speci-
fi cation and colour.
1. Direction indicators :
PY21W (amber).

2. Reversing lamps : P21W.

3. Foglamps/sidelamps :
P21/4W.

4. Sidelamps : P21/4W.

5. Brake lamps/sidelamps : P21/4W.

 Disconnect the electrical connector.

 Unscrew the lamp fi xing nuts in-
side the boot using the towing eye
(stored inside the spare wheel), if
necessary.

 Remove the seal.

 Unclip the bulb holder moving
aside the 5 tabs.

 Unscrew the bulb and change it.

 Refi t the bulb holder.

 Reposition the seal.

1010PRACTICAL INFORMATION
117
Integrated direction indicator side
repeaters CHANGING A REAR BULB (SALOON)
Third brake light:
Five W 5 W bulbs.

 Remove the plastic cover carefully
by unclipping it at the centre and
on either side, perpendicular to its
direction of engagement.

 Press on the two tabs located at
the rear, near the rear screen.

 Pull the red transparent cover out-
wards while maintaining the pressure
on the tabs.

 Change the faulty bulb.

 When refi tting, ensure that the
tabs of the red transparent cover
are engaged correctly and that the
upper trim has been put back in
place correctly.

 Refi t the lamp fi xing nuts inside
the boot using the towing eye, if
necessary. When refi tting, ensure
that the lamp unit is positioned and
fi xed correctly.

 Reconnect the electrical connector.

Number plate lamps : W5W.

 Remove the transparent cover us-
ing a screwdriver blade.

 Change the faulty bulb.

 Push the repeater forwards or
backwards and release it.

 Unclip the repeater and change it.
Repeaters can be obtained from
PEUGEOT dealers.
Amber coloured bulbs (direction indi-
cators and side repeaters), must be
replaced with bulbs of identical speci-
fi cation and colour.
1. Direction indicators :
PY21W (amber).

2. Reversing lamps : P21W.

3. Foglamps/sidelamps :
P21/4W.

4. Sidelamps : P21/4W.

5. Brake lamps/sidelamps : P21/4W.

 Disconnect the electrical connector.

 Unscrew the lamp fi xing nuts in-
side the boot using the towing eye
(stored inside the spare wheel), if
necessary.

 Remove the seal.

 Unclip the bulb holder moving
aside the 5 tabs.

 Unscrew the bulb and change it.

 Refi t the bulb holder.

 Reposition the seal.

1010PRACTICAL INFORMATION
118
CHANGING A REAR BULB (407SW)
Left and right foglamps: P21W.

 Carefully unclip the tailgate interior
trim.

 Detach the sealing fi lm located be-
hind the lamp in question.

 Remove the bulb holder turning it a
quarter of a turn.

 Change the faulty bulb.
When refi tting, ensure that the bulb is
positioned correctly in the bulb holder.

 Unclip the lamp (2 clips).

 Disconnect the connector and re-
move the lamp.

 Unclip the bulb holder moving
aside the 4 tabs.

 Unscrew the bulb and change it.

 Reconnect the connector.

 Refi t the bulb holder. When refi tting
it, ensure that the lamp is correctly
positioned and secured, reclipping
the rear part then the front part.

Number plate lamps: W5W.

 Insert a thin screwdriver in one of
the exterior holes of the transpar-
ent cover.


Push it towards the outside to unclip it.

 Remove the transparent cover.

 Change the faulty bulb. Third brake lamp (diodes)
All work on the diode lamps must be
carried out by a PEUGEOT dealer.
Wing lamps

1. Brake lamps/sidelamps: P21/5W.

2. Reversing lamps: P21W.

3. Direction indicators: P21W.
These three bulbs are changed by re-
moving the lamp.

 Remove the corresponding boot
side fl ap to gain access to the
lamp.

 Remove the lamp fi xing nut inside
the boot.
Note: if necessary, use the wheelbrace
to remove the nuts. In some climatic conditions
(e.g. low temperature or hu-
midity), the presence of misting
on the internal surface of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes.

1010PRACTICAL INFORMATION
125
Without lifting (4 wheels on
the ground)
You must always use a towing bar.
The removable towing eye is inside
the spare wheel.
At the front and at the rear:

 Unclip the cover,

 Screw in the towing eye as far as it
will go. Special requirements with an
automatic gearbox
When towing with the engine switched
off, there is no braking or steering as-
sistance.
Failure to observe this special require-
ment may lead to the destruction of
certain braking units and the absence
of braking assistance when the engine
is re-started.
TOWING YOUR VEHICLE
Lifting (2 wheels only on
the ground)
It is preferable to raise the vehicle with
a professional lifting device.
Place the gear lever in neutral
(position N in the case of the
automatic gearbox).
Towing a vehicle with an auto-
matic gearbox in reverse gear
is prohibited (no lubrication). When towing with four wheels on the
ground, the following rules must be
observed:
- lever in position
N ,
- tow the vehicle at less than 30 mph (50 km/h) over a maximum dis-
tance of 30 miles (50 km).
- do not add oil to the gearbox.

1010PRACTICAL INFORMATION
128
ACCESSORIES
A wide range of accessories recom-
mended by PEUGEOT and original parts
are offered by the dealer network.
They all benefi t from PEUGEOT rec-
ommendation.
These accessories and parts, having
been tested and approved for reliabil-
ity and safety, are all adapted to your
PEUGEOT vehicle.

The product range offered by PEUGEOT
Accessories is structured around 5 catego-
ries: PROTECTION - TOURING - IN-CAR
TECHNOLOGY - STYLING - UNIVERSAL.

Anti-theft alarm, parking sen-
sors, etched windows, wheel
security bolts, fi rst aid kit,
warning triangle, high vis-
ibility safety jacket, snow
chains, anti-slip covers, dog
guard, etc.

"Protection":
Seat covers compatible with
lateral airbags, mats, boot tray.
For leisure pursuits: roof
bars, transport accessories
(bicycle carrier, ski carrier),
roof box, child seats and
booster cushions, rear screen blind,
audio/telephone console, side blinds,
cool box.
Trailer towbar which must be fi tted by
the PEUGEOT Network.
"Touring":
Telephone, Bluetooth sys-
tem, satellite navigation, CD
changer, multimedia, connec-
tion for portable MP3 player
(in the glove box), USB Box.

"In-Car Technology": Alloy wheels, wheel trims,
spoiler, leather steering
wheel, styling strips, door
spoilers, stainless steel sill
protectors.

"Styling":
Windscreen wash fl uid, inte-
rior and exterior cleaning and
maintenance products.

"Universal":
The fi tting of electrical equipment
or accessories which are not rec-
ommended by PEUGEOT may
result in a failure of your vehicle's
electronic system.
Please note this specifi c warning. You
are advised to contact a representa-
tive of the Marque to be shown the
range of recommended equipment
and accessories.

Note
To avoid any jamming under the pedals:
- ensure that the mat is positioned and secured correctly,
- never place one mat on top of an- other.
Depending on the country in
which the vehicle is sold, it
may be compulsory to have
a high visibility safety jacket,
warning triangle and spare
bulbs available in the vehicle.
Installation of radiocommunication
transmitters
It is advisable to contact a representa-
tive of the PEUGEOT marque before
installing accessory radiocommunica-
tion transmitters with external aerial
on your vehicle. The PEUGEOT network will inform
you of the specifi cations (frequency
waveband, maximum output power,
aerial position, specifi c installation
conditions) of the transmitters which
can be fi tted, in accordance with the
Motor Vehicle Electromagnetic Com-
patibility Directive (2004/104/EC).

407SW: you can obtain "Van" conver-
sion kits to convert from a private ve-
hicle to a van.