Engine Peugeot 607 Dag 2002 Owner's Guide

INSTRUMENTS AND CONTROLS
32
STOP warning light
This comes on after the
engine oil pressure, coolant temperature orpuncture warning lights, to which it is linked.
Stop immediately. Contact a PEUGEOT dealer.
Brake fluid level and brake force distribution fault warn ing light
This is linked to the light on the instrument panel.
Display of this warning light accompaned by an audible signa l and the message 'Brake fluid low'indicates an
excessive drop in the brake fluid level.
Display of this warning light, accompanied by an audible sig nal and the message 'Braking system faulty' on the multifunc
tion display indicates a malfunction of the brake force distrib ution system.
Stop immediately in both cases. Contact a PEUGEOT dealer.
Dynamic stability control (ESP/ASR) warning light
Display of this warning light, accompanied by an audible sig nal and the message 'ESP/ASR system faulty' on the
multifunction display indicates a system malfunction.
Contact a PEUGEOT dealer.
Handbrake warning light
Display of this warning light, accompanied by an audible sig nal (vehicle moving) and the message 'Handbrake on'
on the multifunction display, indicates that the handbrake is applied or has not been released correctly.
Battery charge warning light
This comes on each time the ignition key is in the accessories posi tion (1st notch).
Display of this warning light when the engine is running is accompanied by an audible signal and the message 'Bat
tery charge fault' on the multifunction display.
This can indicate:
– faulty operation of the charging circuit,
– loose battery or starter terminals,
– a cut or slack alternator belt,
– an alternator fault.
Contact a PEUGEOT dealer.

INSTRUMENTS AND CONTROLS33
Tyre underinflation warning light
Display of this warning light is acompanied by an audible si
gnal and the message 'Tyre(s) pressure low' on the
multifunction display.
Have the tyre pressure checked as soon as possible.
Low coolant level warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Cooling circuit level low' on
the multifunction display .
Stop immediately.
Warning: wait for the engine to cool before topping up.
The cooling system is pressurised.
In the event of breakdown and to prevent the risk of scalding , unscrew the cap by two turns to allow the pressure to drop.
When the pressure has dropped, remove the cap and top up the level.
Contact a PEUGEOT dealer.
Seat belt not fastened warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Seat belt not fastened' on the
multifunction display.
With the engine running, the warning light comes on when the driver's seat belt is unfastened.
Electronic immobiliser warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Electronic theft protection
faulty' on the multifunction display.
It indicates a malfunction of the electronic immobiliser system.
Contact a PEUGEOT dealer.

INSTRUMENTS AND CONTROLS
34
Water in diesel filter warning light (according to country
)
Display of this warning light is accompanied by an audible si gnal and the message 'Water in diesel filter' on the
multifunction display.
There is a risk of damage to the injection system.
Contact a PEUGEOT dealer as soon as possible.
Front brake pad wear warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Brake pads worn'on the multi
function display.
For your safety, have the pads replaced by a PEUGEOT dealer as soon as the warning light comes on.
Low fuel level warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Fuel level low'on the multi
function display.
When the warning light comes on, you have enough fuel to drive approximately 30 miles (50 km). The tank capac
ity is approximately 80 litres.
Fuel cap warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Fuel cap open'on the multi
function display.
It comes on if the fuel tank cap is not correctly screwed on or is missing.
Door/bonnet/boot open warning light
Display of this warning light with the engine running is accompanied by an audible signal and an illustration on th e
multifunction display, showing which opening has not been correctly closed.
Air bag warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Air bag faulty'on the multi
function display.
Contact your PEUGEOT dealer.

INSTRUMENTS AND CONTROLS35
Engine diagnostics warning light
This is linked to the warning light on the instrument pane
l.
Display of this warning light is accompanied by an audible si gnal and the message 'Engine emission control sys
tem faulty' on the multifunction display.
If it flashes when the engine is running, this indicates a malfunction in the injection, ignition or emission control system. There
is a risk of damage to the catalytic converter (petrol engine onl y).
Contact a PEUGEOT dealer as soon as possible.
Bulb blown warning light
Display of this indicator light is accompanied by an audible signal and the message 'Bulb... faulty' on the multifunc
tion display, indicating the faulty bulb: a bulb in th e dipped beam lights, the side lights, the direction indi cator lights
(except side repeaters) or the brake lights (except the central brake light).
Change the faulty bulb.
Windscreen/headlamp wash reservoir warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Screenwash low'on the multi
function display.
Fill the windscreen/headlamp wash reservoir the next time you st op.
Particulate emission filter saturation warning light (diesel engine)
Display of this warning light is accompanied by an audible si gnal.
When it occurs with the engine running, this indicates the start of saturation of the particulate emission filter (excep
tionally long periods of town type driving conditions: reduce d speed, long tailbacks...).
To regenerate the filter, you are advised to drive as soon as possible and when traffic conditions permit at a speed of 35 mph
(60 km/h) or more for at least five minutes (until the warning li ght goes out).
If the light remains on, contact a PEUGEOT dealer.
Note: After prolonged operation of the vehicle at a very low speed or at idle, you may sometimes notice steam coming from
the exhaust during acceleration. This has no effect on the p erformance of the vehicle or on the environment.

INSTRUMENTS AND CONTROLS37
List of status indicator lights
SPORT suspension indicator light
Display of this indicator light is accompanied by an audible signal.
The indicator light comes on when the SPORTfunction is switched on.
Dynamic stability control (ESP/ASR) system disarming indicato r light
Display of this indicator light when the system is disarmed is acco mpanied by an audible signal and the message
'ASR/ESP systems deactivated' on the multifunction display.
Dynamic stability control (ESP) system operation indicator lig ht
This comes on when the system starts to function.
Diesel engine preheat indicator light
If the temperature is high enough, the indicator light do es not come on and you can start the engine immediately.
If the indicator light does come on, wait for it to go ou t before operating the starter.
Air bag disarming indicator light*
Display of this light is accompanied by an audible signal an d the message 'Passenger air bag disarmed' on the
multifunction display.
If the passenger air bag is disarmed, the indicator light comes on when the ignition is switched on (2nd notch).
In all cases, if the indicator light flashes, contact a PEUGEOT dealer.
*According to country

INSTRUMENTS AND CONTROLS
40
Coolant temperature indicator
When the needle is in
zone A, the
temperature is correct.
When the needle is in zone B, the
temperature is too high.
In cases where the coolant tem
perature warning light comes on
(linked to the STOPwarning light),
you must stop immediately.
Warning: wait for the engine to cool
down.
If necessary, top up the level.
Because the cooling system is pres
surised, to prevent the risk of scald
ing, turn the cap two turns to allow
the pressure to drop.
When the pressure has dropped,
remove the cap and top up the level.
Contact a PEUGEOT dealer.Engine oil level and
temperature
When the ignition is switched on, this
gauge indicates the engine oil level
for approximately 20 seconds, then it
indicates the engine oil temperature.
Engine oil level
The reading is valid only if the vehi
cle is on level ground, and the
engine has been switched off for 10
minutes.
With the ignition on, wait for the
graduated sector to light up and the
indicator needle to move.
When the needle is in zone C, the oil
level is correct.
When the needle is in zone D, the oil
level is incorrect.
There is a risk of damage to the
engine.
 Check the level with the dipstick.
You must top up the level without
exceeding the maximum level on
the gauge.
Engine oil temperature
When the needle is in zone E, the
temperature is correct.
When the needle is in zone F, the
temperature is too high.
Reduce your speed to lower the
temperature.
Service indicator and total
distance recorder
When the ignition is switched on, this
indicates servicing information for a
few seconds, then the total and trip
distances.
Service function
See the 'Service indicator' section.
Total distance recorder function
The total distance is displayed on the
left side of the screen and the trip
distance on the right side.

TELEPHONE: Audio/Telephone RT2
This function is a GSM 900 MHZ telephone incorporated in the audio system.
It possesses a 'hands free'function, provided by a microphone located in the front courte sy light and a steering column
remote control which allows access to most of the functions.
It also possesses a 'confidential' function, provided by the instrument panel located in the u pper casing of the centre front
armrest.
Note: An echo may be heard for a few seconds at the beginning of t he call.
The principal "mobile"type functions are shown on the display incorporated in the a udio system; the menu lists can be
referrred to on the multifunction display.
This function is active when the ignition key is in the accessories position (1st notch), the ignition is switched on (2nd notch),
the engine is running or the vehicle is being driven.
Note: when the ignition key is in the accessories position (1st notch) or the ignition is switched on (2nd notch), this function
will be interrupted after thirty minutes, when the message 'Economy mode active'appears on the multifunction display. If
you are using the telephone at that time, you will be ab le to finish your call.
General information about the display (Audio/Telephone R T2 display)
In telephone mode, the display shows the following informa tion, where applicable.
1. Network signal indicator (3 levels).
2. Service indicator not available.
3. Indicates a communication in progress.
4. Indicator showing connection to an outside network.
5. Indicates:
– when continuously lit: presence of an unread message or message s.
– when flashing: the message tape is full.
6. Display zone (10 symbols x 2 lines).
YOUR 607 IN DETAIL
62

Flashing of the points in
the temperature setting
values indicates that
there is a malfunction of
the air conditioning. Contact your
Peugeot dealer.
11 Air intake/Recir
culation
 Press this button to
recirculate the inte
rior air.
Recirculation insulates
the passenger com
partment from outside smells and
smoke.
Avoid prolonged operation of inte
rior air recirculation (risk of con
densation and deterioration of air
quality).
 Press this button again to return
air intake to automatic control.
YOUR 607 IN DETAIL
92
12 Demisting the
rear screen
 Press this button,
with the engine
running, to demist
the rear screen and
the mirrors.
Demisting stops automatically after
fifteen minutes.  Press again to resume demisting.
If the engine is switched off before
the end of the fifteen minutes,
demisting will resume when the
engine is switched on again.
Note: it is possible to stop demisting
before it goes off automatically, by
pressing the button again.
Note: the condensation created by
the air conditioning system causes a
flow of water under the vehicle when
stationary, which is perfectly normal.9 Switching off the system
 Press the 'OFF'
button.
This action switches
off the display and the
indicator lights and disarms all the
system functions, with the exception
of demisting of the rear screen.
 Press this button, button 5or one
of the two 'AUTO' buttons again to
reactivate the system with the val
ues which were present before it
was switched off.
10 Air flow Press buttons '+'
and ''respectively
to increase or
decrease the air
flow.
As the air flow is
adjusted, the inner sections of the air
flow symbol (fan) are filled in accord
ingly on the
display.

YOUR 607 IN DETAIL95
Memorising using the buttons
To memorise:
 Place the ignition key in the 'run
ning' position (2nd notch),
 Adjust your seat and mirrors,
 Press button M,then button 1
(first driving position) or button 2
(second driving position) within
four seconds.
An audible signal confirms that a
position has been memorised.
Memorising a new position cancels
the previous one.
Recalling a memorised position
Engine off  Briefly press button 1 or 2to recall
the corresponding memorised
position. The end of the setting is
indicated by a bleep.
Note: after recalling a memorised
position five times in succession, the
function will be cancelled until the
engine is started.
Engine running
 Keep button 1 or 2pressed down
until the bleep indicates the end of
setting of the corresponding
memorised position.
Memorising seat
and mirror positions
Four driving positions can be memo
rised:
– two, using two remote control
keys (two users),
– two, using buttons M/1 and M/2.
Driving positions memorised by
the remote control key
When locking the doors, the remote
control key memorises the position
of the driver's seat and the exterior
mirrors.
When unlocking the doors, the dri
ver's seat and the exterior mirrors
resume the position memorised by
the remote control key if this has
changed in the meantime.
Each remote control key can
memorise a specific setting. Front and rear heated seats
controls
 Press the switch. The tempera
ture is regulated automatically.
 Press it again to stop operation.
Note: the command to activate heat
ing of the seat(s) remains in the
memory for two minutes after the
ignition is switched off.

YOUR 607 IN DETAIL95
Memorising using the buttons
To memorise:
 Place the ignition key in the 'run
ning' position (2nd notch),
 Adjust your seat and mirrors,
 Press button M,then button 1
(first driving position) or button 2
(second driving position) within
four seconds.
An audible signal confirms that a
position has been memorised.
Memorising a new position cancels
the previous one.
Recalling a memorised position
Engine off  Briefly press button 1 or 2to recall
the corresponding memorised
position. The end of the setting is
indicated by a bleep.
Note: after recalling a memorised
position five times in succession, the
function will be cancelled until the
engine is started.
Engine running
 Keep button 1 or 2pressed down
until the bleep indicates the end of
setting of the corresponding
memorised position.
Memorising seat
and mirror positions
Four driving positions can be memo
rised:
– two, using two remote control
keys (two users),
– two, using buttons M/1 and M/2.
Driving positions memorised by
the remote control key
When locking the doors, the remote
control key memorises the position
of the driver's seat and the exterior
mirrors.
When unlocking the doors, the dri
ver's seat and the exterior mirrors
resume the position memorised by
the remote control key if this has
changed in the meantime.
Each remote control key can
memorise a specific setting. Front and rear heated seats
controls
 Press the switch. The tempera
ture is regulated automatically.
 Press it again to stop operation.
Note: the command to activate heat
ing of the seat(s) remains in the
memory for two minutes after the
ignition is switched off.