Peugeot 607 Dag 2002 Owner's Guide

INSTRUMENTS AND CONTROLS35
Engine diagnostics warning light
This is linked to the warning light on the instrument pane
l.
Display of this warning light is accompanied by an audible si gnal and the message 'Engine emission control sys
tem faulty' on the multifunction display.
If it flashes when the engine is running, this indicates a malfunction in the injection, ignition or emission control system. There
is a risk of damage to the catalytic converter (petrol engine onl y).
Contact a PEUGEOT dealer as soon as possible.
Bulb blown warning light
Display of this indicator light is accompanied by an audible signal and the message 'Bulb... faulty' on the multifunc
tion display, indicating the faulty bulb: a bulb in th e dipped beam lights, the side lights, the direction indi cator lights
(except side repeaters) or the brake lights (except the central brake light).
Change the faulty bulb.
Windscreen/headlamp wash reservoir warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Screenwash low'on the multi
function display.
Fill the windscreen/headlamp wash reservoir the next time you st op.
Particulate emission filter saturation warning light (diesel engine)
Display of this warning light is accompanied by an audible si gnal.
When it occurs with the engine running, this indicates the start of saturation of the particulate emission filter (excep
tionally long periods of town type driving conditions: reduce d speed, long tailbacks...).
To regenerate the filter, you are advised to drive as soon as possible and when traffic conditions permit at a speed of 35 mph
(60 km/h) or more for at least five minutes (until the warning li ght goes out).
If the light remains on, contact a PEUGEOT dealer.
Note: After prolonged operation of the vehicle at a very low speed or at idle, you may sometimes notice steam coming from
the exhaust during acceleration. This has no effect on the p erformance of the vehicle or on the environment.

INSTRUMENTS AND CONTROLS
36
Antilock braking system (ABS) warning light
This is linked to the warning light on the instrument pane
l.
Display of this warning light is accompanied by an audible si gnal and the message 'ABS faulty' on the multifunc
tion display.
If the warning light remains on, or comes on at over 8 mph (12 km/h), this indicates a malfunction of the ABS.
However, the vehicle retains conventional servoassisted braking.
Contact a PEUGEOT dealer.
Automatic headlamp adjustment warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Automatic adjustment of
headlamps faulty' on the multifunction display.
It comes on if there is a malfunction of the system.
Contact a PEUGEOT dealer. Automatic gearbox fault warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Automatic gearbox faulty' on
the multifunction display.
It comes on if there is an abnormality in the automatic gearbo x.
The gearbox will continue to operate in downgrade mode (lo cked in 3rd gear).
Contact a PEUGEOT dealer. Tyre underinflation detector battery flat / remote control ba ttery flat / impact sensor fault / wheel(s) miss
ing warning light
Display of this warning light is accompanied by an audible si gnal and a message on the multifunction display show
ing the cause of the warning:
– 'Tyre pressure sensor battery charge low',
– 'Remote control battery charge low',
– 'Impact sensor faulty',
– 'X tyre pressure sensor(s) missing'.
Contact a PEUGEOT dealer.

INSTRUMENTS AND CONTROLS37
List of status indicator lights
SPORT suspension indicator light
Display of this indicator light is accompanied by an audible signal.
The indicator light comes on when the SPORTfunction is switched on.
Dynamic stability control (ESP/ASR) system disarming indicato r light
Display of this indicator light when the system is disarmed is acco mpanied by an audible signal and the message
'ASR/ESP systems deactivated' on the multifunction display.
Dynamic stability control (ESP) system operation indicator lig ht
This comes on when the system starts to function.
Diesel engine preheat indicator light
If the temperature is high enough, the indicator light do es not come on and you can start the engine immediately.
If the indicator light does come on, wait for it to go ou t before operating the starter.
Air bag disarming indicator light*
Display of this light is accompanied by an audible signal an d the message 'Passenger air bag disarmed' on the
multifunction display.
If the passenger air bag is disarmed, the indicator light comes on when the ignition is switched on (2nd notch).
In all cases, if the indicator light flashes, contact a PEUGEOT dealer.
*According to country

INSTRUMENTS AND CONTROLS
38
Automatic headlamps disarming indicator light
Display of this light is accompanied by an audible signal.
The light comes on when the function is disarmed.
Automatic headlamps indicator light
Display of this light is accompanied by an audible signal.
The indicator light comes on when the function is activated.
Automatic windscreen wiper disarming indicator light
Display of this light is accompanied by an audible signal.
The indicator light comes on when the function is disarmed.
Automatic windscreen wiper indicator light
Display of this light is accompanied by an audible signal.
The indicator light comes on when the function is activated.
Cruise control indicator light
Display of this light is accompanied by an audible signal.
The indicator light comes on when the function is activated.
AUTO suspension indicator light
Display of this light is accompanied by an audible signal.
The indicator light comes on when the
SPORTfunction is disarmed.

INSTRUMENTS AND CONTROLS
40
Coolant temperature indicator
When the needle is in
zone A, the
temperature is correct.
When the needle is in zone B, the
temperature is too high.
In cases where the coolant tem
perature warning light comes on
(linked to the STOPwarning light),
you must stop immediately.
Warning: wait for the engine to cool
down.
If necessary, top up the level.
Because the cooling system is pres
surised, to prevent the risk of scald
ing, turn the cap two turns to allow
the pressure to drop.
When the pressure has dropped,
remove the cap and top up the level.
Contact a PEUGEOT dealer.Engine oil level and
temperature
When the ignition is switched on, this
gauge indicates the engine oil level
for approximately 20 seconds, then it
indicates the engine oil temperature.
Engine oil level
The reading is valid only if the vehi
cle is on level ground, and the
engine has been switched off for 10
minutes.
With the ignition on, wait for the
graduated sector to light up and the
indicator needle to move.
When the needle is in zone C, the oil
level is correct.
When the needle is in zone D, the oil
level is incorrect.
There is a risk of damage to the
engine.
 Check the level with the dipstick.
You must top up the level without
exceeding the maximum level on
the gauge.
Engine oil temperature
When the needle is in zone E, the
temperature is correct.
When the needle is in zone F, the
temperature is too high.
Reduce your speed to lower the
temperature.
Service indicator and total
distance recorder
When the ignition is switched on, this
indicates servicing information for a
few seconds, then the total and trip
distances.
Service function
See the 'Service indicator' section.
Total distance recorder function
The total distance is displayed on the
left side of the screen and the trip
distance on the right side.

INSTRUMENTS AND CONTROLS39
Automatic gearbox selector lever position indicator ligh
ts
'Park' indicator lights
'Reverse' indicator lights
'Neutral' indicator lights
'Drive' indicator lights
Note: the letter Sand the symbol
linked to the above indicator lights correspond respectively to t he Sport and Snow oper
ating programmes.
'Manual' indicator lights
These indicator lights correspond to the four manually operated gears.

Trip recorder
zero reset
With the ignition on, press
the button.
Manual operation
With the headlamps on, press button
B to increase the brightness of the
instrument panel lighting or button A
to reduce it.
As soon as the lighting reaches the
required level of brightness, release
the button.
INSTRUMENTS AND CONTROLS 41
Illumination
buttons
Automatic operation
The degree of illumination of the
instrument panel automatically
adapts to the external brightness.
By day , the setting cannot be altered.
At night, the brightness can be
increased by means of button B.
A Peugeot dealer is able to cancel
automatic operation if you prefer
manual operation.

YOUR 607 IN DETAIL
42
THE MULTI-FUNCTION
DISPLAY
General
– The multifunction, monochrome Cor colour display shows the
following:
– the time,
– the date,
– the outside temperature (symbol °C flashes if there is a risk of ice),
– the audio system displays,
– the telephone displays,
– status of the openings,
– warning messages (e.g. 'Fuel level low') and vehicle function status
messages, displayed temporarily,
– trip computer display (see corre sponding section),
– satellite navigation system dis plays* (see corresponding sec
tion),
– video images.
It is controlled by a keypad.
Superimposed display
When the status of a function (audio
system, telephone, trip computer,
satellite navigation system,....)
changes while the display has been
showing a different function, a win
dow opens to announce the modifi
cation (information / warning mes
sage), then disappears.
* According to country The control pad
This enables the functions, controls and parameters displayed to
be selected
and validated. It is located next to the display.
Dial
This has two functions:
–Rotation of the dial:
This allows you to move around the screen and thus select a
function.
It also allows you :
– after selection of a 'setting' type parameter, to increase or
decrease the value,
– with a 'list'type parameter, to open the list and scroll through
the values.
– Pressing the dial:
This allows:
– confirmation of the selected function or the modified value.
– selection of a 'setting' or 'list' type parameter in order to
modify it.
– cancelling of a superimposed display.
'MENU' button:
This allows access at any time to the general menu.
'MODE' button:
– brief press: – monochrome screen C: selection of functions (audio system,
navigation / guidance...),
– colour screen: access to the list of controls (context menu) of
the function being displayed.
– Press for more than two seconds: putting the screen on standby.
'ESC' button:
– brief press: cancelling of the operation in progress and a re turn
to the previous screen or erasing of a superimposed display.
– press for more than two seconds: return to the startup screen.

YOUR 607 IN DETAIL43
Setting the parameters
From the
'general menu' , the
'Display configuration' menu
allows you to access the following
parameters:
– setting the video brightness and display,
– setting the date and time,
– choosing the language in which information is heard and displayed
(German, Spanish, French, Eng
lish, Italian), setting the formats
and the units. These settings allow
you to choose a display in km/h or
mph, the temperature in Celsius or
in Fahrenheit, and to modify the
hour (12 or 24 hour) and date
format.
Monochrome screen C
General menu
Press the
'Menu' button to select
one of the following functions:
– navigation/guidance* (see Section on 'Satellite naviga
tion system'),
– display configuration (see paragraph on 'Setting the
parameters', below),
– navigation options* (see Section on 'Satellite naviga
tion system'),
– telephone phone books (see 'RT2 audio equipment' section).
* According to country The colour screen
General menu
From the
general menu, select one
of the following functions by turning
the dial then press the dial to confirm:
• general information,
• navigation/guidance*,
• map*,
• trip computer,
• settings,
• video.
Note: to enable you to make full use
of all the system functions, you have
two CDRoms: one contains the soft
ware and the different languages of
the voice synthesis, the other con
tains the "Satellite navigation sys
tem" map data. The latter must be in
the drive for the "Navigation/Guid
ance" and "Map" functions to be
active.

YOUR 607 IN DETAIL43
Setting the parameters
From the
'general menu' , the
'Display configuration' menu
allows you to access the following
parameters:
– setting the video brightness and display,
– setting the date and time,
– choosing the language in which information is heard and displayed
(German, Spanish, French, Eng
lish, Italian), setting the formats
and the units. These settings allow
you to choose a display in km/h or
mph, the temperature in Celsius or
in Fahrenheit, and to modify the
hour (12 or 24 hour) and date
format.
Monochrome screen C
General menu
Press the
'Menu' button to select
one of the following functions:
– navigation/guidance* (see Section on 'Satellite naviga
tion system'),
– display configuration (see paragraph on 'Setting the
parameters', below),
– navigation options* (see Section on 'Satellite naviga
tion system'),
– telephone phone books (see 'RT2 audio equipment' section).
* According to country The colour screen
General menu
From the
general menu, select one
of the following functions by turning
the dial then press the dial to confirm:
• general information,
• navigation/guidance*,
• map*,
• trip computer,
• settings,
• video.
Note: to enable you to make full use
of all the system functions, you have
two CDRoms: one contains the soft
ware and the different languages of
the voice synthesis, the other con
tains the "Satellite navigation sys
tem" map data. The latter must be in
the drive for the "Navigation/Guid
ance" and "Map" functions to be
active.