ESP Peugeot 607 Dag 2002 Owner's Manual

3YOUR AT A GLANCE
1Lights and direction indica
tors stalk.
2 Steering wheel adjustment.
3 Driver's front air bag.
Horn.
4 Instrument dials.
5 Windscreen wash/wipe
stalk.
Trip computer stalk.
6 Audio remote control stalk.
7 Hazard warning lights
switch.
8 Central adjustable
heating/ventilation vents and
air flow regulation.
9 Sunshine / brightness
sensor.
10 Windscreen demisting
vents.
11 Passenger air bag.
12 Glove compartment.
13 Side adjustable heating/ven
tilation vents and air flow
regulation. 14
Door window demisting
vent.
15 Passenger air bag disarming
switch.
16 Front seats heating switch.
17 Rear ashtray.
Rear lighter.
Rear seats heating switch.
18 Rear footwell heating vent.
19 Twoposition armrest with
compartments.
20 Handbrake.
21 Electronically controlled sus
pension switch.
Doors and boot locking
switch.
Sunroof switch.
Rear blind switch.
22 Front ashtray.
Front lighter.
23 Gear lever.
24 RM2 audio system or RT2
audio/telephone system with
PEUGEOT call button. 25
Heating/ventilation controls.
26 Multifunction display.
27 Steering lock and ignition.
28 Fuse box.
29 Speakers location.
30 Electric mirror controls.
Window controls.
Rear window locking control.
31 Headlamp height adjust
ment.
32 ESP disarming switch.
33 Alarm button.
34 Cruise control.
35 Memory buttons for:
Front seat settings
Electric mirror settings

YOUR AT A GLANCE5
STARTING
STOP position:
The ignition is switched off.
1st notch, Accessories position:The ignition is switched off but
the accessories still function.
2nd notch, Running position:
The ignition is on.
Starting position:
Operates the starter.
Starting a diesel engineIf the temperature is highenough, the preheat
indicator light does not
come on and you can
start immediately.
If the indicator light comes on,
wait for it to go out before operat
ing the starter.
If the engine stalls, it is neces
sary to return the key to the
'Stop' position before restarting. CHECK
(vehicle autotest)
Automatic check
With the ignition on (2nd notch)
If no malfunction has been
detected: In the absence of
vehicle function status indi
cator lights, the OK light is
displayed after two seconds
on the instrument panel screen.
Otherwise, it will be displayed after
these indicator lights come on.
If a 'minor' malfunction has been
detected: the warning light for the
faulty function is displayed on the
instrument panel screen. Certain
indicator lights showing the status of
vehicle functions may also come on,
followed by the OKindicator light.
If a 'major' malfunction has been
detected: the corresponding warn
ing light is displayed on the instru
ment panel screen. Certain indicator
lights showing the status of vehicle
functions may also come on. The
OK indicator light does not come
on. Do not start your vehicle.
Contact a PEUGEOT dealer.
Afterwards, if the passenger air
bag is disarmed, the correspond
ing warning light will come on.
With the engine running or if the
vehicle is moving, the instrument
panel screen temporarily displays:
– lights indicating warnings, when
these occur,
– vehicle function sta tus indicator lights,
when a change
occurs.
The display of certain indicator
lights is accompanied by an audi
ble signal and a message on the
multifunction display.
MANUAL CHECK  Press the "CHECK" button on the
instrument panel.
With the ignition key in the accessories
position, with the ignition switched on,
with the engine running or the vehicle
moving, this function informs you at all
times of the following:
– any current warnings,
– the status of functions which it is possible to switch on or switch off
(windscreen wipers, automatic
switching on of lights, cruise con
trol, disarming of passenger air
bag, etc.).
The corresponding warning lights are
displayed in succession on the instru
ment panel screen.
If a warning or a change of status
occurs during the CHECKmode, the
corresponding indicator light(s) will be
displayed at the end of this mode.
Never run the engine in
a confined space.
Do not make any modi fications to the steering
lock.
31

PEUGEOT SERVICING
22
THE SERVICE LEVELS
Each vehicle has its own servicing cycle, defined by th
e manufacturer in terms of its technical specification.
This cycle consists of alternating 2 types of service A and C, inte rmediate visits and a few additional operations specific to
your vehicle; these correspond to key stages in the life of your 6 07.
At your first and each subsequent service, your dealer will advise you of the type and content of the next service
due.
Intermediate topup
visit.
MAINTENANCE CYCLE FOR YOUR PETROL ENGINE 607
2 litre 16 V and 2.2 litre 16V petrol engines : service e very 2 years or 20,000 miles (30 000 km) maximum (unless the
service indicator shows it is required before this)
1st service at 6,000 miles
(10 000 km) or 6 months*.
This is necessary in order to benefit from the warranty.
MILES (KM) 40,000 (60 000) 80,000 (120 000) 120,000 (180 000)
injection engine: service every 2 years or 20,000 mil es (30 000 km) maximum (unless the service indicator shows it is
required before this)
1st service at 6,000 miles
(10 000 km) or 6 months*.
This is necessary in order to benefit from the warranty.
MILES (KM) 40,000 (60 000) 80,000 (120 000) 120,000 (180 000)
Automatic gearbox oil level every 40,000 miles (60 000 km).
Replacement of brake fluidevery 2 years or 40,000 miles (60 000 km)
These fixed operations are carried out with synthetically based oil. Fuel economy oil
or synthetic oil may also be used (except for the 2.2 litre 16 V petrol engine).
+ replacement of air filter
+ replacement of
24V V6 petrol
+ replacement of air filter + replacement of fuel filterfuel filter
* Whichever comes first.

INSTRUMENTS AND CONTROLS
30
INDICATOR LIGHTS
With the key in the accessories position (1st notch): the batte
ry charge warning light illuminates on the instrument panel display.
With the ignition on (2nd notch): the following three warning lights illuminate on the sides of the instrument panel:
Brake fluid level and brake force distribution fault warning light.
This light should go out after 3 seconds.
If the warning light remains on, or if it comes on when the engine is running and the vehicle is moving, it indicates
an excessive drop in the brake fluid level or a malfunction of the brake force distribution.
Stop immediately. Contact a PEUGEOT dealer.
Antilock braking system (ABS) warning light
This should go out after 3 seconds.
If the warning light remains on or comes on above 8 mph (12 km/h ), this indicates a malfunction of the ABS.
However, the vehicle retains conventional servoassisted braking.
Contact a PEUGEOT dealer.
Engine diagnostics warning light
This should go out 3 seconds after the engine starts.
If it flashes with the engine running, this indicates a ma lfunction in the injection or the ignition system. There is a
risk of damage to the catalytic converter (petrol engine only).
If it is on continuously, this indicates a fault in the e mission control system.
Contact a PEUGEOT dealer as soon as possible.
At the same time, on the instrument panel display: If no malfunction has been detected: the OK light comes on after two seconds (following a black screen), in t he
absence of indicator lights showing the status of vehicle fun ctions. If these indicator lights are present, the OKbut
ton will come on after these. You may start your vehicle.
If a 'minor' malfunction has been detected: the warning light for the faulty function comes on. Certain indicator
lights showing the status of vehicle functions may also come on, followed by the OKindicator light. You can start
your vehicle; however, contact a PEUGEOT dealer as soon as possible.
If a 'major' malfunction has been detected: the corresponding warning light comes on. Certain indicator li ghts showing
the status of vehicle functions may also come on. The OKindicator light does not come on. Do not start your vehicle.
Contact a PEUGEOT dealer.
Afterwards, if the passenger air bag is disarmed, the co rresponding indicator light will come on.

INSTRUMENTS AND CONTROLS31
Coolant temperature warning light
This symbol is accompanied by an audible signal and the message
'Engine temperature too high'
on the multifunction display.
It is linked to the STOPwarning light. Stop immediately.
Warning: wait for the engine to cool.
If necessary, top up the level.
With the engine running and the vehicle moving
The instrument panel display temporarily shows:
– lights indicating warnings, when these occur,
– vehicle function status indicator lights, when a change occu rs.
Certain warning lights may be accompanied by an audib le signal and a
message on the multifunction display.
List of warning symbols MANUAL CHECK
(vehicle autotest)
 Press the "CHECK"button on
the instrument panel.
With the ignition key in the acces
sories position, with the ignition
switched on, with the engine running
or when the vehicle is moving, this
function informs you at all times of
the following: – any current warnings,
– the status of functions which it is possible to switch on or off (wind
screen wipers, automatic switch
ing on of lights, cruise control, dis
arming of passenger air bag, etc.).
The corresponding warning lights
are displayed in succession on the
instrument panel screen.
If a warning or a change of status
occurs during the CHECKmode, the
corresponding indicator lights will be
displayed at the end of this mode.
CHECK mode entry indi
cator light (vehicle
autotest)
This comes on when you
press the 'CHECK' button.
CHECK mode exit indica
tor light (vehicle autotest)
This comes on at the end of
the CHECK mode.
Engine oil pressure warning light
This symbol is accompanied by an audible signal and the message
'Insufficient engine oil pressure' or 'Engine oil pressure too low' on
the multifunction display.
It is linked to the STOPwarning light.
Stop immediately if this comes on when the engine is running.
If there is a lack of oil in the lubrication circuit, top up the level.
Contact a PEUGEOT dealer as soon as possible.
Puncture warning light
This symbol comes on accompanied by an audible signal and the me s
sage 'Punctured tyre(s) detected' on the multifunction display.
It is linked to the STOPwarning light. Stop immediately.
Change the damaged wheel.
Have it repaired by a PEUGEOT dealer.

INSTRUMENTS AND CONTROLS
32
STOP warning light
This comes on after the
engine oil pressure, coolant temperature orpuncture warning lights, to which it is linked.
Stop immediately. Contact a PEUGEOT dealer.
Brake fluid level and brake force distribution fault warn ing light
This is linked to the light on the instrument panel.
Display of this warning light accompaned by an audible signa l and the message 'Brake fluid low'indicates an
excessive drop in the brake fluid level.
Display of this warning light, accompanied by an audible sig nal and the message 'Braking system faulty' on the multifunc
tion display indicates a malfunction of the brake force distrib ution system.
Stop immediately in both cases. Contact a PEUGEOT dealer.
Dynamic stability control (ESP/ASR) warning light
Display of this warning light, accompanied by an audible sig nal and the message 'ESP/ASR system faulty' on the
multifunction display indicates a system malfunction.
Contact a PEUGEOT dealer.
Handbrake warning light
Display of this warning light, accompanied by an audible sig nal (vehicle moving) and the message 'Handbrake on'
on the multifunction display, indicates that the handbrake is applied or has not been released correctly.
Battery charge warning light
This comes on each time the ignition key is in the accessories posi tion (1st notch).
Display of this warning light when the engine is running is accompanied by an audible signal and the message 'Bat
tery charge fault' on the multifunction display.
This can indicate:
– faulty operation of the charging circuit,
– loose battery or starter terminals,
– a cut or slack alternator belt,
– an alternator fault.
Contact a PEUGEOT dealer.

INSTRUMENTS AND CONTROLS37
List of status indicator lights
SPORT suspension indicator light
Display of this indicator light is accompanied by an audible signal.
The indicator light comes on when the SPORTfunction is switched on.
Dynamic stability control (ESP/ASR) system disarming indicato r light
Display of this indicator light when the system is disarmed is acco mpanied by an audible signal and the message
'ASR/ESP systems deactivated' on the multifunction display.
Dynamic stability control (ESP) system operation indicator lig ht
This comes on when the system starts to function.
Diesel engine preheat indicator light
If the temperature is high enough, the indicator light do es not come on and you can start the engine immediately.
If the indicator light does come on, wait for it to go ou t before operating the starter.
Air bag disarming indicator light*
Display of this light is accompanied by an audible signal an d the message 'Passenger air bag disarmed' on the
multifunction display.
If the passenger air bag is disarmed, the indicator light comes on when the ignition is switched on (2nd notch).
In all cases, if the indicator light flashes, contact a PEUGEOT dealer.
*According to country

INSTRUMENTS AND CONTROLS39
Automatic gearbox selector lever position indicator ligh
ts
'Park' indicator lights
'Reverse' indicator lights
'Neutral' indicator lights
'Drive' indicator lights
Note: the letter Sand the symbol
linked to the above indicator lights correspond respectively to t he Sport and Snow oper
ating programmes.
'Manual' indicator lights
These indicator lights correspond to the four manually operated gears.

YOUR 607 IN DETAIL
42
THE MULTI-FUNCTION
DISPLAY
General
– The multifunction, monochrome Cor colour display shows the
following:
– the time,
– the date,
– the outside temperature (symbol °C flashes if there is a risk of ice),
– the audio system displays,
– the telephone displays,
– status of the openings,
– warning messages (e.g. 'Fuel level low') and vehicle function status
messages, displayed temporarily,
– trip computer display (see corre sponding section),
– satellite navigation system dis plays* (see corresponding sec
tion),
– video images.
It is controlled by a keypad.
Superimposed display
When the status of a function (audio
system, telephone, trip computer,
satellite navigation system,....)
changes while the display has been
showing a different function, a win
dow opens to announce the modifi
cation (information / warning mes
sage), then disappears.
* According to country The control pad
This enables the functions, controls and parameters displayed to
be selected
and validated. It is located next to the display.
Dial
This has two functions:
–Rotation of the dial:
This allows you to move around the screen and thus select a
function.
It also allows you :
– after selection of a 'setting' type parameter, to increase or
decrease the value,
– with a 'list'type parameter, to open the list and scroll through
the values.
– Pressing the dial:
This allows:
– confirmation of the selected function or the modified value.
– selection of a 'setting' or 'list' type parameter in order to
modify it.
– cancelling of a superimposed display.
'MENU' button:
This allows access at any time to the general menu.
'MODE' button:
– brief press: – monochrome screen C: selection of functions (audio system,
navigation / guidance...),
– colour screen: access to the list of controls (context menu) of
the function being displayed.
– Press for more than two seconds: putting the screen on standby.
'ESC' button:
– brief press: cancelling of the operation in progress and a re turn
to the previous screen or erasing of a superimposed display.
– press for more than two seconds: return to the startup screen.

YOUR 607 IN DETAIL
56
Automatic storing of FM stations in the memory (autostore) Press button Bfor more than two seconds, to automatically store the 6 station s with the strongest signal in
FM. These stations are stored in the FMast waveband.
If it is not possible to find 6 stations, the remaining memo ries are empty.
Recalling stations stored in the memory
For each waveband, briefly press buttons '1'to '6' to recall the corresponding station.
The list of the 6 stations stored on the waveband is displa yed each time one of the buttons '1' to '6' is pressed.
RDS SYSTEM
Using the RDS (Radio Data System) function on FM
Radio Data System allows you to continue listening to the sa me station, whatever frequency it is using for the region you a re
going through.
RM2 audio: Press the 'RDS' button to switch the function on or off.
RT2 audio: Press the '
jj✱ RDS'button to switch the function on or off.
The display will show:
– 'RDS' if the function is selected.
– '(RDS)' or'RDS
' if the function is selected but not available.
RDS station following
The display indicates the name of the station selected. The radio is continually searching for the station which has the best
reception and which is transmitting the same programme.