PEUGEOT 807 2006 Service Manual

Steering wheel controls
Switching the function off
Place dial in position 0 or switch off the
ignition to switch the system off. The
last programmed speed remains in the
memory.
Exceeding the programmed speed
Pressing the accelerator pedal in order to
exceed the programmed speed will have
no effect unless you press the pedal firmly
beyond the point of resistance .
The limiter is deactivated temporarily
and the programmed speed which is still
displayed flashes.
To return to the limiter function, reduce your
speed to below the programmed speed.
Flashing of the speed
The speed flashes: following forcing of the accelerator point of
resistance,
 when the limiter cannot prevent an
increase in the vehicle speed due to the
profile of the road or on a steep descent,
 in the event of sharp acceleration.
In any event, the speed limiter cannot
replace the need to observe speed
limits, nor can it replace the need for
vigilance and responsibility on the part of the
driver.
Always pay attention to the profile of the
road and take care on sharp acceleration.
To avoid any jamming under the pedals:
- ensure that the mat is positioned correctly,
- never place one mat on top of another.
Operating fault
The programmed speed is cleared and the
dashes flash for a few seconds.
Contact a PEUGEOT dealer to have the
system checked.
42

Air conditioning
ERGONOMICS and COMFORT
2
43
AIR CONDITIONING

Air conditioning
44
To ensure an even distribution of air, ensure
you do not block the air intake grille at the
base of the windscreen, the side vents, the
air outlets on the floor and the air extractor
at the tailgate pillars.
Operate the air conditioning system for
5 to 10 minutes, once or twice a month,
to keep it in perfect working order.
Have the filter elements replaced regularly
(air filter and passenger compartment filter).
If the environment is dusty, change them
twice as often.
If the system does not produce cold air,
do not use it and contact your PEUGEOT
dealer.
The condensation created by the air
conditioning system results in a flow of water
under the vehicle when stationary which is
perfectly normal.CORRECT USE OF THE AIR
CONDITIONING
Whenever possible use the system in AUTO
mode, if your vehicle is equipped with
automatic air conditoning, as this enables
the air flow, air temperature within the
passenger compartment, air distribution and
air intake or air recirculation to operate to
optimum effect.
To be effective, you should operate the air
conditioning only with the windows closed.
If the interior temperature remains high after
a lengthy period in the sun, do not hesitate
to ventilate the passenger compartment for
a few moments. ADDITIONAL HEATER
Vehicles fitted with HDI engines may be
fitted with automatic additional heating to
improve your comfort.
With the engine at idle or when the vehicle
is stationary, it is normal to notice a high-
pitched whistling and a slight emission of
smoke and odour.

Air conditioning
44
To ensure an even distribution of air, ensure
you do not block the air intake grille at the
base of the windscreen, the side vents, the
air outlets on the floor and the air extractor
at the tailgate pillars.
Operate the air conditioning system for
5 to 10 minutes, once or twice a month,
to keep it in perfect working order.
Have the filter elements replaced regularly
(air filter and passenger compartment filter).
If the environment is dusty, change them
twice as often.
If the system does not produce cold air,
do not use it and contact your PEUGEOT
dealer.
The condensation created by the air
conditioning system results in a flow of water
under the vehicle when stationary which is
perfectly normal.CORRECT USE OF THE AIR
CONDITIONING
Whenever possible use the system in AUTO
mode, if your vehicle is equipped with
automatic air conditoning, as this enables
the air flow, air temperature within the
passenger compartment, air distribution and
air intake or air recirculation to operate to
optimum effect.
To be effective, you should operate the air
conditioning only with the windows closed.
If the interior temperature remains high after
a lengthy period in the sun, do not hesitate
to ventilate the passenger compartment for
a few moments. ADDITIONAL HEATER
Vehicles fitted with HDI engines may be
fitted with automatic additional heating to
improve your comfort.
With the engine at idle or when the vehicle
is stationary, it is normal to notice a high-
pitched whistling and a slight emission of
smoke and odour.

Air conditioning
45
ERGONOMICS and COMFORT
2
Demisting, visibility programme
De-icing the rear screen and mirrors
It is possible to stop the de-icing before
it is switched off automatically by
pressing this button again.
DE-ICING AND DEMISTING
The comfort programme may not
be sufficient to quickly demist or
de-ice the windows (humidity,
several passengers, ice).
In this case, select the visibility programme.
The visibility programme indicator light
comes on.
It activates the air conditioning, the air flow,
the de-icing of the rear screen and provides
optimum distribution of the ventilation to the
windscreen and side windows.
It deactivates the air recirculation.
Press this button, with the engine
running, to de-ice the rear screen
and mirrors.
The de-icing indicator light comes
on. The duration of de-icing depends on the
exterior temperature.
Pressing the button again reactivates the
de-icing.

51
6
4
32
8
9Air conditioning
AUTOMATIC AIR CONDITIONING WITH SEPARATE SETTINGS
Do not cover the sunshine sensor
located in the centre of the fascia. This
is used to regulate the air conditioning.Located on the centre console, the control
panel is to the right of the gear lever.
The driver and front passenger can each
adjust the air temperature to suit their
requirements.
They can also activate or disarm the rear
ventilation adjustment controls. 1 - AUTO mode
This is the normal air conditioning
operating mode.
Press the "AUTO" button.
Depending on the comfort temperature
selected, the system controls the air
distribution, flow and intake so that the
passenger compartment is comfortable and
has an adequate circulation of air. You do
not have to make any further adjustments.
When the engine is cold, in order to prevent
a rush of cold air, the ventilation will reach
its optimum level progressively.
The "AUTO" symbol is displayed.
For your comfort, the settings selected
when the ignition is switched off will be
retained when it is switched on again, if the
temperature in the passenger compartment
has not changed significantly; otherwise,
operation will resume in automatic mode.
47
ERGONOMICS and COMFORT
2

Air conditioning
482 - Driver ’s temperature adjustment 4 - Adjustment of the air
distribution
 Pressing the corresponding
button(s) 4 allows you to
position the air flow towards:
 the windscreen,
 the side vents and the central
vents,
 the side vents, the central vents
and the footwells,
 the windscreen and the
footwells,
 the footwells.
The indicator light corresponding to the
position selected 4 comes on. 5 - Adjustment of the rear
ventilation
("REAR" version)
To permit adjustment of the
ventilation to the rear passengers, press the
REAR button.
The rear ventilation symbol is displayed.
The 2nd row side vents air
flow adjustment controls
are operational and can be
adjusted.
To deactivate the rear
ventilation controls, press
the REAR button again.
The rear ventilation symbol
switches off.
Take care not to obstruct
the side vents and the air
outlets on the floor.
MONO Version
Press this button once to obtain
an even temperature throughout
the passenger compartment. The
reference value is selected by the
driver.
3 - Passenger ’s temperature
adjustment
The required value is displayed (from 14 to
28: comfort value = 21).
The maximum difference between the
value displayed for the driver and for the
passenger may not be greater than 5.
If you use these manual adjustments, the
AUTO symbol switches off. Press the corresponding "+" and "-"
buttons to adjust.
To make the driver and passenger setting
the same: air conditioning with "MONO" version,
press the MONO button.
 air conditioning with "REAR" version,
press the + button for more than
two seconds.
On entering the vehicle, the interior
temperature may be considerably lower
(or higher) than is comfortable. It is not
necessary to change the value displayed
in order to quickly obtain the desired level
of comfort. The system will operate at
maximum performance to reach the comfort
value set.

Air conditioning
ERGONOMICS and COMFORT
2
6 - Adjustment of the air flow

Turn control knob 6 to the right
or to the left respectively to
increase or decrease the air flow.
On the display, the blades of the fan darken
when the air flow is increased.
7 - Switching the system off  Turn air flow control knob 6 to the left until
the display switches off.
The action disarms all the system functions,
with the exception of demisting of the rear
screen. Your comfort setting is no longer
maintained and switches off.
For your comfort, avoid remaining in the off
position. Operating control knob 6 again or the
"Visibility" button or "AUTO" button
reactivates the system with the values which
were present before it was switched off.
Flashing of the points in the temperature
setting values indicates that there is a
malfunction of the air conditioning.
Contact your PEUGEOT dealer. 8 - Intake of exterior air/
Recirculation of interior air

Press this button to recirculate
the air inside.
The air recirculation symbol and indicator
light 8 are displayed.
Recirculation insulates the passenger
compartment from outside smells and smoke. 9
- Air conditioning On/Off
 Press this button to activate
automatic operation of the air
conditioning.
The symbol and the indicator light 9 are
displayed. Press this button again to switch off the air
conditioning.
The symbol and the indicator light 9 switch off.
49
Avoid prolonged operation of interior
air recirculation (risk of misting of the
windows and deterioration of air quality).
 Press this button again to return air intake
to automatic control.

5
4
6 1 32
Seats
FRONT SEATS WITH MANUAL
ADJUSTMENT
2 - Seat back angle adjustment
Pull the lever upwards and set the required
angle.
1 - Forwards/backwards adjustment
Lift the bar and slide the seat forwards or
backwards.
50SEATS

3 - Driver ’s seat height adjustment
Manoeuvre the handle upwards or
downwards until the desired position is
reached.
4 - Driver ’s seat lumbar adjustment
Move the lever up or down to obtain the
required position.5 - Head restraint height and angle
adjustment
To raise or lower the restraint, pull it
forwards, then slide it.
The adjustment is correct when the upper
edge of the head restraint is level with the
top of the head.
To remove it, set it in the high position, lift
the tab using a coin and pull upwards and
forwards at the same time.
To re-install, engage the head restraint rods
in the holes, making sure they are aligned
with the seat back. 6 - Rotating of seats*
Place the seat back in the upright position.
Place the seat in the highest intermediate
longitudinal position.
On the driver ’s side, push the steering
wheel, apply the handbrake. To allow
rotation of the seat, lower the handbrake
handle pulling on the end.
Pull the control upwards and rotate the seat
inwards.
Never drive with the head restraints
removed; they must be in place and
correctly adjusted. This pivoting operation must be carried
out with the engine switched off.
Driving with a passenger seated facing the
rear is prohibited.
* According to version or equipment. SeatsERGONOMICS and COMFORT
2
51
For further information regarding
releasing of the handbrake, refer to
the "Driving Safety" section of the "Safety"
chapter.