PEUGEOT 807 2006 Workshop Manual

5
4
6 3
1-2
Seats
FRONT SEATS WITH ELECTRICAL
ADJUSTMENT
2 - Driver ’s seat height adjustment
Push the rear part of the control upwards or
downwards to obtain the required height.
1 - Forwards-backwards adjustment
Push the control forwards or backwards to
slide the seat.
52

Seats
3 - Seat back angle adjustment
Tilt the control to the front or the rear to
obtain the angle required.
The electrical functions of the seats are
cancelled one minute after the ignition
has been switched off.
4 - Driver ’s seat lumbar adjustment
(mechanical)
Raise or lower the lever to obtain the correct
position. 5 - Head restraint height and angle
adjustment (manual)
To raise or lower the head restraint, pull it
forwards, then slide it.
The setting is correct when the upper edge
of the head restraint is level with the top of
the head.
To remove the head restraint, place it in the
high position, lift the tab using a coin and
pull upwards and forwards at the same time.
To re-install, engage the head restraint rods
in the holes, making sure they are aligned
with the seat back.
Never drive with the head restraints
removed; they must be in place and
correctly adjusted.
6 - Rotating of seats (mechanical)
Place the seat back in the upright position.
Place the seat in the highest intermediate
longitudinal position.
On the driver ’s side, push the steering
wheel, apply the handbrake. To allow
rotation of the seat, lower the handbrake
handle pulling on the end.
Pull the control upwards and rotate the seat
inwards.
This pivoting operation must be carried
out with the engine switched off.
Driving with a passenger seated facing the
rear is prohibited.
53
ERGONOMICS and COMFORT
2

Seats
Memorising seat positions
Two driving positions can be memorised,
using buttons M/1 and M/2.
These are located on the side of the seat: Place the ignition key in the ‘running’
position (2nd notch),
 Adjust your seat,
 Press button M, then button 1 for a first
driving position within four seconds.
Repeat the same actions on buttons M and
2 to store another driving position.
An audible signal confirms that a position
has been memorised.
Memorising a new position cancels the
previous one.
Activating a memorised driving position
Engine off  Briefly press button 1 or 2 to recall the
corresponding memorised position. Front heated seat controls
When the engine is running, the front seats
can be heated separately.
Use the adjustment controls located on the
side of each front seat to switch on and
select the self-regulated level of heating:
1:
Low.
2: Medium.
3: High.
0: Off.
After recalling a memorised position
five times in succession, the function
will be cancelled until the engine is started.
Engine running  Keep button 1 or 2 pressed down until
the end of setting of the corresponding
memorised position.
54

Seats
Rear side seats
Two rear passenger seats, left and right side posit ion, 2nd and 3rd
row. Rear centre seat
One rear passenger seat, 2nd row central position a
nd 3rd row left
side position. Integrated seat belt. Plastic shell trim. Folds to the low
table position.
Rear bench seat
One three-seat bench seat, 3rd row position. Pullman seat
Equipment dedicated to the special version of the 8
07.
Four rear passenger seats with armrests.
2nd and 3rd row side position.
55
ERGONOMICS and COMFORT
2

1 2 3 4
1 2 3 4
A
B
C
B
c
REAR SIDE SEATS
Forwards/backwards adjustment
Lift bar A and slide the seat forwards or
backwards.
Adjusting the angle of the seat back
Push lever B upwards and adjust the angle
as required.
Release the lever to lock. Handling the side seat
Access to the 3rd row
1 -
Place the head restraint in the low position.
2 - Push lever B upwards as far as possible.
3 - Fold the seat back onto the seat
cushion and guide the tilting of the seat back forwards until the rear anchorages
are unlocked. If you experience any
difficulty, use the emergency control to
unlock the anchorages.
4 - Place the seat in the vertical closed
position.
Exit from the 3rd row
1 - Place the head restraint in the low position.
2 - Pull control C.
3 - Guide the tilting of the seat back
forwards until the rear anchorages
are unlocked. If you experience any
difficulty, use the red emergency control
to unlock the anchorages. 4 -
Place the seat in the vertical closed
position.
Seats
56
Following each entry or exit, reposition
the raised seat guiding it until the rear
anchorages lock in their rails.

1 2 3 41 2
3
Control for sliding the rear side seats
from the 3rd row or the boot
Pull the strap (marked with the arrow
symbol) to slide the seat in front of you.
Removing the side seat
1 -
Tilt the seat back forwards to detach
the rear anchorages.
2 - Grab the red strap which appears and
pull it upwards, the front anchorages
unlock.
Refitting the side seat 3 -
The strap, like the handle, enables you
to remove the seat. Seats
1 - Place the front anchorages at the front
stop in the slides. Support the strap
firmly for easier positioning of the seat.
2 - Tilt the folded seat towards the rear.
The rear anchorages lock.
3 - Raise the seat back.
4 - Slide the seat.
Check that there is no obstacle
obstructing the slides or preventing
correct locking of the seat anchorages.
57
ERGONOMICS and COMFORT
2

1 2 3
1 23 4
Seats
2ND ROW CENTRE SEAT
This can be placed in the 3rd row, on the left."Low table" position
1 -
Place the head restraint in the low
position.
2 - At the top (at the back of the seat), lift
the handle identified by the symbol
and guide the tilting of the seat back
towards its seat cushion. 3 -
You have a "low table". To return to the
seat position, lift the handle and guide
the raising of the seat back.
Removing the centre seat
1 - Place the seat in the "low table"
position.
2 - Using the control which you pull, tilt the
seat back forwards so releasing the rear
anchorages from the slides. 3 -
Grab the red strap which appears and
pull it upwards, the front anchorages
unlock.
4 - The strap, like the handle, enables you
to remove the seat.
58

1 2 3
Seats
Rear head restraints
The rear head restraints can be removed
and have two positions:high, position for use,
 low, storage position.
To raise or lower a head restraint, pull it
forwards sliding it at the same time.
To remove it, place it in the high position,
push the lug and pull it forwards and
upwards.
To refit it, engage the head restraint rods
in the holes taking care to remain in the
centreline of the seat back.
Never drive with the head restraints
removed, they must be in place and
correctly adjusted.
Refitting the centre seat
Check that there is no obstacle
obstructing the slides or preventing
correct locking of the seat anchorages.
1 - Place the front anchorages at the front
stop in the slides. Support the strap
firmly for easier positioning of the seat.
2 - Tilt the folded seat towards the rear.
The rear anchorages lock.
3 - Raise the seat back and slide the seat.
Turning a rear seat round

The rear seats can be placed in a "face to
face" position.
Carry out the operations described for
removal then turn the seat round and
resume with the procedure for refitting the
seat.
This turning operation must be carried
out when stationary.
Driving with a passenger seated facing the
rear is prohibited.
When the vehicle is being driven, placing
a 2nd row seat in the closed position while
a passenger is sitting in the 3rd row is
prohibited.
ERGONOMICS and COMFORT
2
59

1 2 3
Seats
Rear head restraints
The rear head restraints can be removed
and have two positions:high, position for use,
 low, storage position.
To raise or lower a head restraint, pull it
forwards sliding it at the same time.
To remove it, place it in the high position,
push the lug and pull it forwards and
upwards.
To refit it, engage the head restraint rods
in the holes taking care to remain in the
centreline of the seat back.
Never drive with the head restraints
removed, they must be in place and
correctly adjusted.
Refitting the centre seat
Check that there is no obstacle
obstructing the slides or preventing
correct locking of the seat anchorages.
1 - Place the front anchorages at the front
stop in the slides. Support the strap
firmly for easier positioning of the seat.
2 - Tilt the folded seat towards the rear.
The rear anchorages lock.
3 - Raise the seat back and slide the seat.
Turning a rear seat round

The rear seats can be placed in a "face to
face" position.
Carry out the operations described for
removal then turn the seat round and
resume with the procedure for refitting the
seat.
This turning operation must be carried
out when stationary.
Driving with a passenger seated facing the
rear is prohibited.
When the vehicle is being driven, placing
a 2nd row seat in the closed position while
a passenger is sitting in the 3rd row is
prohibited.
ERGONOMICS and COMFORT
2
59

1 2 3
1 2 3 4
A
C
B
D
5
c
c
Seats
REAR BENCH SEAT
Forwards/backwards adjustment
From the seat cushion, lift bar A and slide
the seat towards the front or the rear.
From the boot, you can pull on strap B
and slide the seat forwards to make it
easier to load the vehicle.
The rear bench seat must only be
fitted in the 3 rd
row.
Seat back folded position
1 - Place the head restraints in the low
position.
2 - Pull the strap C upwards, from the
tailgate. 3 -
Tilt the seat back on the seat cushion.
Vertical position of the bench seat
1 - Place the head restraints in the low
position.
2 - Pull the strap C upwards, from the
tailgate.
3 - Fold the seat back onto the seat
cushion. 4 -
Pull the lever D to unlock the rear
anchorages.
5 - Place the seat in the vertical "folded"
position.
When driving, attach the retaining
straps to the handles.
60