Peugeot Expert Dag 2006 Owner's Guide

23Instruments and controls-
Automatic gearbox
indicator
Automatic gearbox indicator
light:"SNOW" indicator light
This comes on when the au-
tomatic gearbox "SNOW"
operating program is se-
lected.
Automatic gearbox lever
positions: "Park"
"Reverse"
"Neutral"
"Drive"
Instrument panel display
After switching on the ignition, two
functions are shown in succession:
- service indicator (see correspond-ing section),
- total distance recorder (see corre- sponding section).
Note: it displays the total and trip
distances for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on
locking and unlocking the vehicle.
"Manual" mode:
1st gear engaged
2nd gear engaged
3rd gear engaged
4th gear engaged

Instruments and controls24 -
Instrument panel display
After switching on the ignition, three
functions are shown in succession:
- service indicator (see corresponding section),
- engine oil level indicator,
- total distance recorder (see corre- sponding section).
Note: it displays the total and trip
distances for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on locking
and unlocking the vehicle.
Engine oil level
indicator
When the ignition is switched on,
the engine oil level is indicated for
approximately 10 seconds, after the
service information.
Never exceed the maximum
level as a surplus of oil may
damage the engine.
Consult a PEUGEOT dealer
as soon as possible.Oil level gauge
fault
"Min"
and "max"
flashing indicates a
malfunction.
Check the level using
the dipstick.
Consult a PEUGEOT dealer.
Maximum
Minimum
Check the level us-
ing the dipstick and
top it up.
The reading is only valid if the vehicle
is on level ground and the engine has
been off for 15 minutes.
Lack of oil
Flashing of the seg-
ments indicates an
insufficient level of
oil.
It is essential that the oil level
is topped up. There is a risk of
damage to the engine.

Instruments and controls24 -
Instrument panel display
After switching on the ignition, three
functions are shown in succession:
- service indicator (see corresponding section),
- engine oil level indicator,
- total distance recorder (see corre- sponding section).
Note: it displays the total and trip
distances for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on locking
and unlocking the vehicle.
Engine oil level
indicator
When the ignition is switched on,
the engine oil level is indicated for
approximately 10 seconds, after the
service information.
Never exceed the maximum
level as a surplus of oil may
damage the engine.
Consult a PEUGEOT dealer
as soon as possible.Oil level gauge
fault
"Min"
and "max"
flashing indicates a
malfunction.
Check the level using
the dipstick.
Consult a PEUGEOT dealer.
Maximum
Minimum
Check the level us-
ing the dipstick and
top it up.
The reading is only valid if the vehicle
is on level ground and the engine has
been off for 15 minutes.
Lack of oil
Flashing of the seg-
ments indicates an
insufficient level of
oil.
It is essential that the oil level
is topped up. There is a risk of
damage to the engine.

25Instruments and controls-
Service indicator
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the man-
ufacturer's servicing schedule.
Operation
As soon as the ignition is switched
on and for 5 seconds, the spanner
symbolising ''service operation'' is lit.
The trip recorder display shows the
distance remaining (in round figures)
before the next service.
Example: 4,800 miles/km remain be-
fore the next service is due. When the
ignition comes on and for 5 seconds
the display indicates:
5 seconds after the ignition is
switched on, the total distance re-
corder resumes normal operation
and the display shows the total or trip
distances. The distance remaining before the
next service is less than 500 miles
(1,000 km).
Example:
400 miles (900 km) remain
before the next service is due.
When switching on the ignition and
for 5 seconds, the display shows:
5 seconds after the ignition is
switched on, the total distance re-
corder resumes normal operation
and the symbol remains lit.
This indicates that a service should
be carried out shortly. The display
shows the total or trip distances. 5 seconds after the ignition is
switched on, the total distance re-
corder resumes normal operation and
the symbol remains lit. The display
shows the total or trip distances.
The service is overdue*.
Each time the ignition is switched on
and for 5 seconds, the symbol and
the excess distance flash.
Example:
the service is overdue by
300 miles/km. The service should be
carried out very shortly.
When the ignition is switched on and
for 5 seconds, the display shows:
* Whichever comes first: the service spanner lights if the two-year inter-
val has been exceeded.

Instruments and controls26 -
Resetting the service
indicator
Your PEUGEOT dealer carries out
this operation after each service.
The reset procedure is as follows:
- Switch off the ignition.
- Press and hold button 1.
- Switch on the ignition.
The display begins a 10 second
countdown.
- Keep button 1 pressed for 10 seconds.The display shows [= 0] and the
service symbol disappears.
Total distance recorder
Briefly pressing button 1 alternates
between the total and trip distance
displays.
To reset the trip recorder to zero,
when it is displayed press button 1
until zeros appear.
DIGITAL CLOCK
The clock is set with the ignition on,
engine off .
Press button A for more than three
seconds, the hours begin to flash.
You can now set the hours by press-
ing button A. Five seconds after
the button is released, the hours
are stored and the minutes begin to
flash.
You can now set the minutes. Five
seconds after the button is released,
the minutes are stored.
Note: press button A briefly for slow
advance or press and hold for rapid
advance.

27Instruments and controls-
LIGHTING
RHEOSTAT
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or re-
duce) the brightness.
As soon as the lighting is of the
required brightness, release the
button.
LIGHTING
RHEOSTAT
With the lights on, turn the knob to
vary the intensity of the lighting of the
instruments and controls.

Audio equipment28 -
RD1 STEERING WHEEL CONTROLS

29Audio equipment-
PressFunction carried out
1
Increase volume.
2Decrease volume.
3Selection of previous stored station (radio) - Selection of previou s CD (CD changer).
4Selection of next stored station (radio) - Selection of next CD (CD changer).
5Automatic search of lower frequencies (radio) - Selection of previous track (CD/CD changer).
6Automatic search of higher frequencies (radio) - Selection of next track (CD/CD changer).
7Change of audio source (radio/CD/CD changer).
8Mute; sound restored by pressing any button.

Audio equipment30 -
ButtonFunction
A ON/VOLPress: set on/off. Rotation: volume adjustment.
BEjection of the CD.
C RDSRDS function on/off.
Press for more than 2 seconds: regional following mode on/off.
D TATraffic information priority on/off.
Press for more than 2 seconds: PTY function on/off.
E AUDIOSelection of the bass, treble, loudness and sound distributio n setting.
F
Increase of the setting of the functions associated with but
ton E.
AUDIO RD1

31Audio equipment-
ButtonFunction
G
Decrease of the setting of the functions associated with but ton E.
H
Automatic search of higher frequency.
Selection of next CD track.
I MANManual/automatic operation of buttons H and J.
J
Automatic search of lower frequency.
Selection of previous CD track.
KSource selection: radio. Selection of FM1, FM2, FM3 and AM waveba nds.
Press for more than 2 seconds: automatic storing of stations (autosto re).
LSource selection: CD changer.
Press for more than 2 seconds: shuffle.
MSource selection: CD.
Press for more than 2 seconds: shuffle.
1 to 6 1 2 3 4 5 6
Selection of the stored station.
Press for more than 2 seconds: storing a station.
Selection of a CD.