engine PONTIAC GRAND PRIX 2007 Owners Manual

Vehicle Damage Warnings
Also, in this manual you will nd these notices:
Notice:These mean there is something
that could damage your vehicle.
A notice tells about something that can damage
the vehicle. Many times, this damage would not be
covered by your vehicle’s warranty, and it could
be costly. But the notice will tell what to do to help
avoid the damage.
When you read other manuals, you might see
CAUTION and NOTICE warnings in different colors
or in different words.
There are also warning labels on the vehicle.
They use the same words, CAUTION or NOTICE.
Vehicle Symbols
The vehicle has components and labels that use
symbols instead of text. Symbols are shown along
with the text describing the operation or information
relating to a specic component, control, message,
gage, or indicator.
If you need help guring out a specic name of a
component, gage, or indicator, reference the
following topics:
Seats and Restraint Systems in Section 1
Features and Controls in Section 2
Instrument Panel Overview in Section 3
Climate Controls in Section 3
Warning Lights, Gages, and Indicators in
Section 3
Audio System(s) in Section 3
Engine Compartment Overview in Section 5
5

Keys.............................................................. 84
Remote Keyless Entry (RKE) System.......... 86
Remote Keyless Entry (RKE) System
Operation................................................. 87
Doors and Locks.......................................... 92
Door Locks................................................. 92
Power Door Locks....................................... 94
Delayed Locking.......................................... 94
Programmable Automatic Door Locks.......... 95
Rear Door Security Locks........................... 95
Lockout Protection....................................... 96
Trunk.......................................................... 96
Windows....................................................... 98
Power Windows.......................................... 99
Sun Visors................................................ 100
Theft-Deterrent Systems............................. 100
Content Theft-Deterrent............................. 100
PASS-Key
®III ........................................... 102
PASS-Key®III Operation........................... 103
Starting and Operating Your Vehicle......... 105
New Vehicle Break-In................................ 105
Ignition Positions....................................... 105
Retained Accessory Power (RAP)............. 106
Starting the Engine.................................... 107Engine Coolant Heater.............................. 108
Active Fuel Management™........................ 109
Automatic Transaxle Operation.................. 110
Parking Brake........................................... 115
Shifting Into Park (P) ................................. 116
Shifting Out of Park (P)............................. 117
Parking Over Things That Burn................. 118
Engine Exhaust......................................... 119
Running the Engine While Parked............. 120
Mirrors......................................................... 121
Manual Rearview Mirror with OnStar
®....... 121
Outside Power Mirrors............................... 121
Outside Convex Mirror............................... 122
OnStar
®System.......................................... 122
Storage Areas............................................. 126
Glove Box................................................. 126
Cupholder(s).............................................. 126
Sunglasses Storage Compartment............. 127
Front Seat Storage Net............................. 127
Center Console Storage Area.................... 127
Assist Handles.......................................... 127
Convenience Net....................................... 127
Sunroof....................................................... 128
Section 2 Features and Controls
83

Remote Keyless Entry (RKE)
System Operation
The vehicle’s doors can be locked and unlocked,
and the trunk can be opened from about
3 feet (1 m) up to 60 feet (18 m) away with
the remote keyless entry transmitter.
If your vehicle has the remote vehicle start
feature, you can also start the vehicle’s engine
with the remote keyless entry transmitter.The following functions may be available with your
vehicle’s remote keyless entry system:/(Remote Vehicle Start):If your vehicle has
this feature, the engine may be started from
outside the vehicle using the remote keyless entry
transmitter. See “Remote Vehicle Start” later in
this section for more detailed information.
Q(Lock):Press the lock button to lock all the
doors. If enabled through the Driver Information
Center (DIC), the parking lamps may ash
once and the horn may chirp once to indicate
locking has occurred. See “REMOTE LOCKS
FEEDBACK” underDIC Controls and Displays
(Base Level DIC) on page 186orDIC Controls and
Displays (Uplevel DIC with Trip Computer) on
page 190for programming information. Pressing
the lock button will arm the content theft-deterrent
system. SeeContent Theft-Deterrent on
page 100for more information.
Remote Keyless Entry
with Remote StartRemote Keyless Entry
without Remote Start
87

3. Put the two halves back together. Make sure
the cover is on tight so water will not get
inside the transmitter.
4. Test the operation of the transmitter with the
vehicle.
Remote Vehicle Start
Your vehicle may have a remote start feature.
This feature allows you to start the engine
from outside the vehicle. It may also start the
vehicle’s heating or air conditioning systems and
rear window defogger. When the remote start
system is active, the climate control system will
heat or cool the inside of the vehicle based on the
outside temperature. The rear window defogger
will be turned on by the climate control system
when it is heating the inside of the vehicle. Normal
operation of the system will return after the key
is turned to RUN.
Laws in some communities may restrict the use of
remote starters. For example, some laws may
require a person using remote start to have
the vehicle in view when doing so. Check local
regulations for any requirements on remote starting
of vehicles.Do not use the remote start feature if your vehicle
is low on fuel. Your vehicle may run out of fuel.
The remote start feature provides two separate
starts per ignition cycle, each with 10 minutes of
engine running time.
The remote start system needs to be reset after
your vehicle’s engine is started two times using the
transmitter’s remote start button. The remote
start system is reset by inserting the vehicle’s key
into the ignition switch and turning to RUN.
SeeIgnition Positions on page 105for information
regarding the ignition positions on your vehicle.
Your remote keyless entry transmitter with
the remote start button provides an increased
range of operation. You can start your vehicle from
about 492 feet (150 m) away. However, the
range may be less while the vehicle is running,
and as a result you may need to be closer to your
vehicle to turn it off than you were to turn it on.
There are other conditions which can affect
the performance of the transmitter, seeRemote
Keyless Entry (RKE) System on page 86for
additional information.
90

/(Remote Start):If your vehicle has the remote
vehicle start feature, the keyless entry transmitter
will have a button with this symbol on it.
To start the vehicle using the remote start feature,
do the following:
1. Aim the transmitter at the vehicle.
2. Press and release the transmitter’s lock
button, then immediately press and hold
the transmitter’s remote start button for
4 seconds or until the vehicle’s turn signal
lamps ash. The vehicle’s doors will be
locked.
3. When the vehicle starts, the parking lamps
will turn on and remain on while the engine
is running, and the DIC will display REMOTE
START ACTIVE PRESS HAZARD SWITCH
TO CANCEL.
The engine will shut off automatically after
10 minutes, unless a time extension has been
done or the vehicle’s key is inserted into
the ignition switch and turned to RUN.
If you enter the vehicle after a remote start,
and the engine is still running, insert the
key into the ignition switch and turn to RUN
to drive the vehicle.4. To manually shut off a remote start, do any of
the following. The parking lamps will turn off.
Aim the remote keyless entry transmitter
at the vehicle, and press the remote
start button.
Turn on the hazard warning ashers.
Turn the ignition switch to RUN and then
to OFF.
Your vehicle’s engine can be started two times
using the transmitter’s remote start feature. If only
one remote start procedure has been done,
since last driving the vehicle, or resetting the
remote start system, the engine may be started
again remotely by following the remote start
procedure a second time.
If the remote start procedure is used again before
the rst 10 minute time frame has ended, the
rst 10 minutes will immediately expire and
the second 10 minute time frame will start.
The remote vehicle start feature will not operate if
any of the following occur:
The remote start system is disabled through
the DIC.
The vehicle’s key is in the ignition.
A door on the vehicle is open.
91

The vehicle’s hood is open.
The hazard warning ashers are on.
There is an emission control system
malfunction.
The engine coolant temperature is too high.
The oil pressure is low.
Two remote vehicle starts have already been
provided for that ignition cycle.
If a remote start is attempted and is unsuccessful,
the Driver Information Center (DIC) will display
REMOTE START DISABLED.
Vehicles that have the remote vehicle start feature
are shipped from the factory with the remote start
system enabled. The system may be enabled/
disabled through the DIC. See “REMOTE START”
underDIC Controls and Displays (Base Level DIC)
on page 186orDIC Controls and Displays (Uplevel
DIC with Trip Computer) on page 190for additional
information.
Remote Start Ready
If your vehicle does not have the remote vehicle
start feature, it may have the remote start
ready feature. This feature gives you the ability tolock or unlock your vehicle from about 492 feet
(150 m) away and allows your dealer to add
the manufacturer’s remote vehicle start feature.
See your dealer if you would like to add the
manufacturer’s remote vehicle start feature to
your vehicle.
Doors and Locks
Door Locks
{CAUTION:
Unlocked doors can be dangerous.
Passengers, especially children, can
easily open the doors and fall out of a
moving vehicle. When a door is
locked, the handle will not open it.
You increase the chance of being
thrown out of the vehicle in a crash if
the doors are not locked. So, wear
safety belts properly and lock the
doors whenever you drive.
CAUTION: (Continued)
92

When you want to open a rear door when the
security lock is on, do the following:
1. Unlock the door using the remote keyless
entry transmitter, if equipped, the power
door lock switch, or by lifting the rear door
manual lock.
2. Open the door from the outside.
To cancel the rear door security lock, do the
following:
1. Unlock the door and open it from the outside.
2. Insert the key into the security lock slot
and turn it so the slot is in the vertical position.
Lockout Protection
The lockout protection feature makes it more
difficult to lock the key in the vehicle. If the driver’s
door is open while the key is in the ignition, the
door cannot be locked with the power door
lock switch.
This feature cannot guarantee that you will never be
locked out of the vehicle. If the key is not left in the
ignition, or, if the manual door lock pin is used, the
key could still be locked inside the vehicle. Always
remember to take the key with you.
Trunk
{CAUTION:
It can be dangerous to drive with the trunk
lid open because carbon monoxide (CO)
gas can come into your vehicle.
You cannot see or smell CO. It can cause
unconsciousness and even death. If you
must drive with the trunk lid open or if
electrical wiring or other cable connections
must pass through the seal between the
body and the trunk lid:
Make sure all other windows are shut.
Turn the fan on your heating or cooling
system to its highest speed and select
the control setting that will force
outside air into your vehicle. See
Climate Control System.
If you have air outlets on or under
the instrument panel, open them all
the way.
SeeEngine Exhaust on page 119.
96

PASS-Key®III Operation
The vehicle is
equipped with
PASS-Key
®III
(Personalized
Automotive Security
System) theft-deterrent
system. PASS-Key
®III
is a passive
theft-deterrent
system.
This means nothing special needs to be done to
arm or disarm the system. It works when the key is
inserted or removed from the ignition.
PASS-Key
®III uses a transponder in the ignition
key that matches a decoder in the vehicle.
When the PASS-Key
®III system senses that the
wrong key has been inserted into the ignition, it
shuts down the vehicle’s starter and fuel systems.The starter will not work and fuel will stop owing to
the engine. If someone tries to start the vehicle
again with the wrong key, the vehicle will not start.
Anyone using a trial-and-error method to start the
vehicle will be discouraged to do so because of the
high number of electrical key codes.
When trying to start the vehicle, if the engine does
not start and the STARTING DISABLED DUE TO
THEFT SYSTEM warning message on the Driver
Information Center (DIC) comes on, the key may
have a damaged transponder. Turn the ignition off
and try again.
If the engine still does not start, and the key
appears to be undamaged, try another ignition key.
At this time, you may also want to check the fuse.
SeeFuses and Circuit Breakers on page 460.Ifthe
engine still does not start with the other key, the
vehicle needs service. If the vehicle does start, the
rst key may be faulty. See your dealer who can
service the PASS-Key
®III to have a new key made.
In an emergency, contact Roadside Assistance.
SeeRoadside Assistance Program on page 498for
more information.
103

It is possible for the PASS-Key®III decoder
to accept the transponder value of a new or
replacement key. Up to 10 keys may be
programmed for the vehicle. If all the programmed
keys are lost or do not operate, see your GM dealer
or a locksmith who can service PASS-Key
®III to
have keys made and programmed to the system.
Canadian Owners: If all the keys are lost or
damaged, only a GM dealer can service
PASS-Key
®III to have new keys made and
programmed to the system.
The following procedure is for programming a new
or replacement key when you have at least one
already programmed key. To program the new key
do the following:
1. Verify that the new key has PK3 stamped on it.
2. Insert the master key in the ignition and start
the engine. If the engine will not start, see
your dealer for service.
3. After the engine has started, turn the key to
OFF, and remove the key.4. Insert the key to be programmed and turn it to
RUN within ve seconds of removing the
original key.
5. The STARTING DISABLED DUE TO THEFT
SYSTEM warning message on the DIC will
turn off, once the key has been programmed.
It may not be apparent that the SERVICE
THEFT SYSTEM warning message went on
due to how quickly the key is programmed.
6. Repeat Steps 1 through 5 if additional keys
are to be programmed.
If the STARTING DISABLED DUE TO THEFT
SYSTEM warning message appears and stays on
the DIC while the vehicle is being driven, the
engine will be able to be restarted if it is turned
off. Your PASS-Key
®III system, however, is
not working properly and must be serviced by
your dealer. The vehicle is not protected by
the PASS-Key
®III system at this time.
If the PASS-Key
®III key is lost or stolen, see
your dealer or a locksmith who can service
PASS-Key
®III to have a new key made.
104

Starting and Operating Your
Vehicle
New Vehicle Break-In
Notice:Your vehicle does not need an
elaborate break-in. But it will perform better in
the long run if you follow these guidelines:
Do not drive at any one constant speed, fast
or slow, for the rst 500 miles (805 km).
Do not make full-throttle starts. Avoid
downshifting to brake, or slow, the vehicle.
Avoid making hard stops for the rst
200 miles (322 km) or so. During this time
your new brake linings are not yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking-in guideline every time
you get new brake linings.
Do not tow a trailer during break-in. See
Towing a Trailer on page 324for the trailer
towing capabilities of your vehicle and more
information.
Following break-in, engine speed and load can
be gradually increased.
Ignition Positions
The ignition switch is located on the instrument
panel, to the right of the steering column.
There are four different
positions. Insert the key
in the ignition and
turn it to the right for
each position.
9(OFF):This position locks the ignition,
steering wheel and transaxle. It is a theft-deterrent
feature. This is the only position from which the
key can be removed.
Notice:Using a tool to force the key from the
ignition switch could cause damage or break
the key. Use the correct key and turn the key
only with your hand. Make sure the key is all the
way in. If it is, turn the steering wheel left and
right while you turn the key hard. If none of this
works, then your vehicle needs service.
105