front assembly PONTIAC VIBE 2007 Owners Manual

Your vehicle has a crash sensing and
diagnostic module which records information
after a crash. SeeVehicle Data Collection and
Event Data Recorders on page 411.
Let only qualied technicians work on the
airbag system. Improper service can mean that
the airbag system will not work properly. See
your dealer for service.
Passenger Sensing System
Your vehicle has a passenger sensing system. A
passenger airbag status indicator on the
instrument panel will be visible when you turn your
ignition key to ON.
The words ON and OFF
will be visible in the
passenger airbag status
indicator during the
system check.When the system check is complete, either the
word ON or the word OFF will be visible depending
on whether the seat is occupied and/or the
weight of the occupant. SeePassenger Airbag
Status Indicator on page 163. The passenger
sensing system will turn off the right front
passenger’s frontal airbag, seat-mounted side
impact airbag (if equipped), and the safety
belt pretensioner under certain conditions. The
driver’s airbags are not part of the passenger
sensing system.
The passenger sensing system works with sensors
that are part of the right front passenger’s seat
assembly and safety belt assembly. The sensors
are designed to detect the presence of a
properly-seated occupant and determine if the right
front passenger’s frontal airbag, seat-mounted side
impact airbag (if equipped), and the safety belt
pretensioner should be enabled (may inate) or not.
74

Replacing Restraint System Parts
After a Crash
{CAUTION:
A crash can damage the restraint systems
in your vehicle. A damaged restraint
system may not properly protect the
person using it, resulting in serious injury
or even death in a crash. To help make
sure your restraint systems are working
properly after a crash, have them
inspected and any necessary
replacements made as soon as possible.
If you have had a crash, do you need new belts or
LATCH system parts?
After a very minor collision, nothing may be
necessary. But if the belts were stretched, as they
would be if worn during a more severe crash,
then you need new parts.
If the LATCH system was being used during a
more severe crash, you may need new LATCH
system parts.If belts are cut or damaged, replace them.
Collision damage also may mean you will need to
have LATCH system, safety belt or seat parts
repaired or replaced. New parts and repairs may
be necessary even if the belt or LATCH system
was not being used at the time of the collision.
If an airbag inates, you will need to replace airbag
system parts. See the part on the airbag system
earlier in this section.
If the frontal airbags inate you will also need to
replace the driver and front passenger’s safety belt
retractor assembly. Be sure to do so. Then the
new retractor assembly will be there to help protect
you in a collision.
After a crash you may need to replace the driver
and front passenger’s safety belt retractor
assemblies, even if the frontal airbags have not
deployed. The driver and front passenger’s safety
belt retractor assemblies contain the safety belt
pretensioners. Have your safety belt pretensioners
checked if your vehicle has been in a collision,
or if your airbag readiness light stays on after you
start your vehicle or while you are driving. See
Airbag Readiness Light on page 162.
83

Your vehicle also has a safety belt reminder light
for the right front passenger position.
This light is located on
the center of the
instrument panel, above
the audio system.
When the key is turned to ON or START, this light
will come on as a reminder for the right front
passenger to fasten their safety belt. This light will
ash until the right front passenger’s safety belt
is buckled. The passenger’s safety belt reminder
light will not come on if the right front passenger’s
belt is already buckled or if a sensor does not
detect the weight of a passenger in that seat.
If something is placed on the right front passenger
seat, the sensors in the seat may detect that
object and cause the right front passenger safety
belt reminder light to come on. If this happens,
remove the object.Airbag Readiness Light
There is an airbag readiness light on the instrument
panel cluster, which shows the airbag symbol. The
system checks the airbag’s electrical system for
malfunctions. The light tells you if there is an
electrical problem. The system monitors the airbag
sensor assembly, front airbag sensors,
seat-mounted side impact and roof-mounted airbag
sensors, driver’s seat position sensor, driver’s seat
belt buckle switch, right front occupant sensing
system and indicator light, front passenger’s seat
belt buckle switch, seat belt pretensioner
assemblies, inators, interconnecting wiring and
power sources. For more information on the airbag
system, seeAirbag System on page 63.
This light will come on
briey when you start
your vehicle, then
it should go out. This
means the system
is ready.
162

Headlamps, Front Turn Signal,
and Parking Lamps
A. Headlamp
B. Turn Signal/Parking LampTo replace the headlamp, turn signal, or parking
lamp bulb, do the following:
1. Open the hood and locate the lamp assembly.
2. Remove the rubber cover and socket from
the headlamp or turn signal/parking lamp.
316