warning PORSCHE 911 GT3 2010 5.G Manual PDF

Instruments, On-Board Computer
139
Tire pressure warnings
The tire pressure warning light on the instrument
panel and a corresponding message on the on-
board computer warn about loss of pressure in
two stages, depending on the amount of pressure
loss.
Driving with insufficient tire pressure reduces the
road safety of the vehicle and destroys the tire and
wheel.
Stage 1 – Add air
The pressure in the tire is too low by 4 to 7 psi (0.3
to 0.5 bar).
fThe tire pressure warning contains the
affected tire with the tire pressure to be added.
Correct the tire pressure at the next
opportunity. This tire pressure warning appears
– for approx. 10 seconds with vehicle stopped
when switching off the ignition or
– again when switching on the ignition.
With ignition on, the warning can be deactivated.
The tire pressure warning light in the instrument
panel goes out only when the tire pressure has
been corrected.Stage 2 – Flat tire
At speeds below 100 mph (160 km/h):
The pressure in the tire has dropped by more
than 7 psi (0.5 bar). This significant pressure
loss is a danger to road safety.
At speeds above 100 mph (160 km/h):
The pressure in the tire has dropped by more
than 5 psi (0.4 bar). This significant pressure
loss is a danger to road safety.
fWhen the tire pressure warning appears, stop
immediately at a suitable location. Check the
indicated tire for signs of damage. If neces-
sary, fill in tire sealant and set the correct tire
pressure.
10_GT3_21.book Seite 139 Donnerstag, 4. Juni 2009 12:48 12

140
Instruments, On-Board Computer This tire pressure warning also appears when
driving and can be acknowledged.
The tire pressure warning light on the instrument
panel goes out only when the tire pressure has
been corrected.
System learningThe Tire Pressure Monitoring begins to “learn” the
wheels after a wheel change, wheel transmitter
replacement or update of the tire settings. During
this process, the Tire Pressure Monitoring recog-
nizes the tires and their locations.
The on-board computer displayes the message
“TPM is learning, monitoring not act.”.
The Tire Pressure Monitoring requires a certain
amount of time to learn the wheels. During this
time, the current tire pressures are not available
on the on-board-computer:
– The tire pressure warning light remains lit until
all wheels have been learned.
– The display of the tire pressure function of the
on-board computer shows lines.
– The required pressures for cold tires at 68 °F
(20 °C) are indicated in the Info pressure
display in the tire pressure menu.
Position and pressure information is displayed as
soon as the Tire Pressure Monitoring has
assigned the wheels identified as belonging to the
vehicle to the correct wheel positions.The wheel learning process takes place
exclusively when the vehicle is being driven
(vehicle speed above 16 mph (25 km/h)).
fCheck the tire pressure for all wheels on the
“Info pressure” display.
fCorrect the tire pressure to the required
pressure if necessary.
Changing a wheel and replacing tiresfNew wheels must be fitted with radio transmit-
ters for the Tire Pressure Monitoring.
Before tires are changed, the battery charge
state of the wheel transmitters should be
checked at an authorized Porsche dealer.
fSwitch the ignition off when changing a wheel.
The tire settings on the on-board computer must
be updated after changing a wheel.
If the tire settings are not updated, the message
“Wheel change? Input new TPM settings!” is
displayed on the on-board computer.
fUpdate the on-board computer settings when
the vehicle is stationary the next time.
10_GT3_21.book Seite 140 Donnerstag, 4. Juni 2009 12:48 12

Instruments, On-Board Computer
141
Warning!
Your vehicle has also been equipped with a Tire
Pressure Monitoring (TPM) malfunction indicator
when the system is not operating properly.
The TPM malfunction indicator is combined with a
low tire pressure telltale.
When the system detects a malfunction, the
telltale will flash for approx. one minute and then
remain continuously illuminated. This sequence
will continue upon subsequent vehicle start-ups as
long as the malfunction exists.
When the malfunction indicator is illuminated, the
system may not be able to detect or signal low tire
pressure as intended.
TPM malfuntions may occur for a variety of
reasons, including the installation of replacement
or alternate tires or wheels on the vehicle that
prevent the TPM from functioning properly.
Always check the TPM malfunction telltale after
replacing one or more tires or wheels on your
vehicle to ensure that the replacement or alter-
nate tires and wheels allow the TPM to continue to
function properly.The warning light in the speedometer lights up:
– When a loss in pressure has been detected.
– When learning newly mounted wheels/wheel
sensors, as long as the vehicle’s own wheels
have not yet been recognized.
In the event of a defect in Tire Pressure Monitoring
or a temporary fault, the warning light in the
speedometer flashes for approx. one minute and
then remains continuously illuminated.
The tire pressure warning light in the instrument
panel goes out only when the cause of the fault
has been rectified.
Partial monitoringMonitoring of the other wheels is continued if there
is a fault in one or two wheel transmitters.
– The tire pressure warning light lights up.
– The message “TPM partial monitoring” is
displayed on the on-board computer.
– No tire pressures are displayed on the on-
board computer for wheels with faulty wheel
transmitters.
No monitoringIn the event of faults the Tire Pressure Monitoring
cannot monitor the tire pressure.
The warning light on the instrument panel flashes
for approx. one minute and then remains conti-
nuously illuminated and a corresponding message
appears on the on-board computer.
Monitoring is not active when:
– the Tire Pressure Monitoring is faulty,
– wheel transmitters for the Tire Pressure
Monitoring are missing,
– during the learning phase after the tire settings
have been updated,
– after a wheel change without updating the tire
settings,
– more than four wheel transmitters are
detected,
– there is external interference by other radio
sources, e.g. wireless headphones,
– tire temperatures are too high.
fPlease see the chapter “WARNINGS ON THE
INSTRUMENT PANEL AND THE ON-BOARD
COMPUTER” on Page 148.
Warning light
10_GT3_21.book Seite 141 Donnerstag, 4. Juni 2009 12:48 12

142
Instruments, On-Board Computer
A-Tire pressure
B-Tire temperature
C-Tire pressures for cold tires
D-Tire pressure for hot tires
E-Pressure increase as the result of temperature
increase
F-Pressure drop in faulty/leaking tiresPressure increase as the result of
temperature increase1. Required-pressure line
2. Warning stage 1
(from –4 to –7 psi (–0.3 bar to –0.5 bar))
3. Warning stage 2
At speeds above 100 mph (160 km/h):
(from –5 psi (–0.4 bar))4. Warning stage 2
At speeds below 100 mph (160 km/h):
(from –7 psi (–0.5 bar))
In accordance with physical principles, the air
pressure changes as the temperature changes.
The tire pressure increases or decreases by
around 1.5 psi (0.1 bar) for every 18 °F (10 °C)
change in temperature.
The Tire Pressure Monitoring takes this relation-
ship between tire pressure and temperature into
account.
Tire pressure specificationsInformation on tire pressure for public roads can
be found in this Owner's Manual in the Technical
Data chapter or on the tire-pressure plate in the
left door aperture.
These values apply to cold tires at 68 °F (20 °C)
ambient temperature.
10_GT3_21.book Seite 142 Donnerstag, 4. Juni 2009 12:48 12

144
Instruments, On-Board Computer 6. If the segments are filled in up to the top line,
the oil level has reached the maximum mark.
Under no circumstances add engine oil.7. If only the bottom segment is filled in, the oil
level has reached the minimum mark.
Add engine oil immediately.
8. If the bottom segment flashes, the oil level has
dropped to below the minimum mark.
Add engine oil immediately.
The difference between the minimum and
maximum marks on the segment display is
approx. 1.1 quarts (1.0 liters).
One segment of the display between the minimum
and maximum marks corresponds to a top-up
quantity of approx. 0.32 quarts (0.3 liter).fAdd engine oil if necessary.
Switch off ignition before adding engine oil.
fPlease see the chapter “ENGINE OIL LEVEL”
on Page 160.
fNever add more engine oil than required
to reach the maximum mark.
Failure
A failure of the oil level display is indicated by a
warning message on the on-board computer.
Display “Check oil level”
The on-board computer display “Check oil level” is
an additional reminder to you to check the oil level.
The display depends on the distance travelledand
the operating conditions, and does not indicate
whether or not the oil level is correct.
10_GT3_21.book Seite 144 Donnerstag, 4. Juni 2009 12:48 12

148
Warnings
Warnings on the instrument panel and the on-board computerIf a warning message appears, always refer to the corresponding chapters in the Owner’s Manual.
Warning messages are issued only if all measurement preconditions are met. Therefore, check all fluid levels regularly –
in particular, always check the engine oil level before refuelling.Acknowledging warning messagesWarning messages can be deleted from the on-board computer display.
fPush the on-board computer operating lever forward.
You can recall erased warning messages in the “INFO” menu.
Instrument
panelOn-board
computerText display on on-board
computerMeaning/measure
Seat belt Driver and passenger must fasten their seat belts.
Handbrake Handbrake is still on.
Ignition key
not removed
Replace battery
in ignition keyReplace the remote-control battery.
Ignition lock faulty,
visit workshopHave the fault remedied at an authorized Porsche dealer.
Ignition lock faulty,
visit workshop nowHave the fault remedied at an authorized Porsche dealer.
Relieve steering Relieve the steering lock by moving the steering wheel to the left or right.
Steering locked The steering wheel lock remains engaged.
Have the fault remedied at an authorized Porsche dealer.
10_GT3_21.book Seite 148 Donnerstag, 4. Juni 2009 12:48 12

Warnings
149
Lights on Low beam/side marker lamps on
Parking light on Left/right parking light on
Check left/right dipped beam (low
beam)
also applies to:
high beam, side indicator light,
reversing lightThe reported light is faulty. Check bulb.
Have the fault remedied at an authorized Porsche dealer.
Daytime
driving lights offDaytime running lights switch off when the engine is shut off. Switch on lights if necessary.
Dynamic
cornering light
failureDynamic cornering light faulty.
Have the fault remedied at an authorized Porsche dealer.
Headlight beam
adjustment faultyHave the fault remedied at an authorized Porsche dealer.
Front lid not closed Close luggage compartment lid properly.
Rear lid not closed Close engine compartment lid properly.
Rain sensor faulty Have the fault remedied at an authorized Porsche dealer.
Refill washer fluid
LIMIT
Cannot be accepted
with vehicle stoppedThe current speed can only be accepted for the acoustic warning signal when the vehicle is in motion.
LIMIT
30Selected speed limit (e.g. 30 mph) for the acoustic warning signal has been exceeded.
Adjust your speed if necessary.
Instrument
panelOn-board
computerText display on on-board
computerMeaning/measure
10_GT3_21.book Seite 149 Donnerstag, 4. Juni 2009 12:48 12

150
Warnings
Fuel gauge warning
lightConsider remaining range Refuel at next opportunity.
Check engine oil level Start engine oil level measurement in the on-board computer.
Engine oil pressure too low Stop immediately at a suitable place, measure oil level with the on-board computer and, if necessary,
add engine oil.
Warning light
Temperature gaugeEngine temperature too high Switch engine off and let it cool.
Check coolant level and, if necessary, add coolant.
Temperature gauge
warning light flashesCheck coolant level Switch engine off and let it cool.
Check coolant level and, if necessary, add coolant.
Check engine
visit workshopStop immediately at a suitable place and check tank cap for proper fastening. If the tank cap was
fastened correctly, consult your authorized Porsche dealer.
Reduced engine power Consult your authorized Porsche dealer.
Temperature gauge
warning light flashesFailure of
engine compartment blowerConsult your authorized Porsche dealer.
Warning Battery/generator Stop at a safe place and switch the engine off. Do not continue driving.
Have the fault remedied at an authorized Porsche dealer.
Failure
oil pressure
indicatorHave the fault remedied at an authorized Porsche dealer.
Failure
oil level
indicatorHave the fault remedied at an authorized Porsche dealer.
Oil temperature
indicator faultyHave the fault remedied at an authorized Porsche dealer.Instrument
panelOn-board
computerText display on on-board
computerMeaning/measure
10_GT3_21.book Seite 150 Donnerstag, 4. Juni 2009 12:48 12

Warnings
151
Failure indicator Coolant indicator failed.
Have the fault remedied at an authorized Porsche dealer.
Failure
outside temp.
indicatorOutside temperature indicator failed.
Have the fault remedied at an authorized Porsche dealer.
Service
wear on
brake padsHave the brake pads changed immediately at an authorized Porsche dealer.
Warning
Brake fluid levelStop immediately in a suitable place.
Do not continue driving. Have the fault remedied at an authorized Porsche dealer.
Warning
Brake distributionStop immediately in a suitable place.
Do not continue driving. Have the fault remedied at an authorized Porsche dealer.
ABS failure Have the fault remedied at an authorized Porsche dealer.
SC off
Continuous display: SC offStability Control (SC) switched off.
SC+TC off
Continuous display: SC+TC offStability Control (SC) and Traction Control (TC) switched off.
SC+TC on Stability Control (SC) and Traction Control (TC) switched on.
PSM failure Have the fault remedied at an authorized Porsche dealer.
Instrument
panelOn-board
computerText display on on-board
computerMeaning/measure
10_GT3_21.book Seite 151 Donnerstag, 4. Juni 2009 12:48 12

152
Warnings
PA S M N o r m a l / S p o r t I n d i c a t or for selected PASM mode
PASM failure Have the fault remedied at an authorized Porsche dealer.
PASM indicator faulty Have the fault remedied at an authorized Porsche dealer.
PADM failure Dynamic engine mounting failed.
Have the fault remedied at an authorized Porsche dealer.
System fault airbag Airbag is faulty.
Have the fault remedied at an authorized Porsche dealer.
Check passenger’s seat setting Weight sensing is impaired on the passenger's seat (Advanced Airbag).
Correct the seating position, set the backrest upright, do not support weight on the armrests, or lift on
the handles.
Depress clutch pedal Depress clutch pedal when starting.
System fault
visit workshopSeveral systems may have failed. Adjust your driving style. Reduce speed.
Have the fault remedied at an authorized Porsche dealer.
Failure
fuel level indicator
workshopHave the fault remedied at an authorized Porsche dealer.
Service in mls/days (km/days) Service indicator
Bring the vehicle in for service no later than after the distance/time shown has elapsed.
Please see the additional information in the “Maintenance” booklet.
Service now Service indicator
Have your vehicle serviced at an authorized Porsche dealer.
Flat tyre! Tire Pressure Monitoring has detected a serious pressure loss.
Stop at a suitable place and check tires for damage. Fill in tire sealant if necessary.
Instrument
panelOn-board
computerText display on on-board
computerMeaning/measure
10_GT3_21.book Seite 152 Donnerstag, 4. Juni 2009 12:48 12