display PORSCHE CAYNNE 2010 1.G Manual Online

180
Driving and Driving Safety Switching Sport mode on and off
Sport mode can be activated when the ignition is
switched on and when the on-road driving program
High Range (without reduction) is selected.
fPress SPORT button E in the center console.
When Sport mode is switched on, the light-
emitting diode F in the SPORT button is lit.
When Sport mode is switched on, the logo SPORT
appears on the multi-purpose display.
After the ignition is switched off, Sport mode is
automatically reset to Normal mode.
Warning messages
A warning appears on the multi-purpose display of
the instrument panel in the event of a fault.
fFor information on warning messages on the
multi-purpose display:
Please see the chapter “OVERVIEW OF
WARNING MESSAGES” on Page 149.Vehicles with air suspension
If you wish to use the characteristics of Sport
mode and the sports exhaust system, but would
like a more comfortable running-gear setup, you
can:
– switch PASM and PDCC separately to Normal
or Comfort mode and/or
– raise the ride height of the vehicle.
fPress the corresponding PASM button in the
center console. The light-emitting diode in the
button of the selected running-gear setup
lights up.
In addition, the selected running-gear setup is
shown on the multi-purpose display of the
instrument panel for approx. 12 seconds.
Please see the chapter “PORSCHE ACTIVE
SUSPENSION MANAGEMENT (PASM)” on
Page 193.
Please see the chapter “PORSCHE DYNAMIC
CHASSIS CONTROL (PDCC)” on Page 194.
Press the rocker switch in the center console for-
ward. The corresponding light-emitting diode next
to the rocker switch lights up continuously after
the adjustment process. The level change is also
indicated on the multi-purpose display of the in-
strument panel.
Please see the chapter “AIR SUSPENSION WITH
LEVEL CONTROL AND HEIGHT ADJUSTMENT” on
Page 190.
10_Cayenne_21_KW17.book Seite 180 Donnerstag, 9. April 2009 3:33 15

Driving and Driving Safety
185
Switching off PSMfPress PSM OFF button A.
PSM is switched off after a short delay.
The light-emitting diode in the button is lit up.
When the PSM is switched off, the multifunctio-
nal PSM light on the instrument panel is lit and
a message appears in the multi-purpose dis-
play of the instrument panel.During braking, the vehicle is stabilized even
when PSM is switched off.
One-sided spinning of the wheels is prevented,
even with PSM switched off.
PSM should always be switched on during
“normal” driving.
However, it can be of advantage to switch off PSM
temporarily in exceptional situations:
– On a loose surface or in deep snow
– When “rocking the vehicle free”
– When using snow chains.
Vehicles with Tiptronic: When the PSM is
switched off the slip monitoring function is also
deactivated.– The multifunctional light on the instrument pa-
nel lights up for a lamp check when the ignition
is switched on.
– The light indicates a control operation, inclu-
ding when PSM is switched off (brake control
in the event of one-sided wheel spin).
– In conjunction with the multi-purpose display on
the instrument panel, the light indicates that
PSM is switched off.
– Faults are displayed by the light in conjunction
with the multi-purpose display of the instru-
ment panel.
PSM is out of order.
fConsult your authorized Porsche dealer.
Multifunctional PSM light
10_Cayenne_21_KW17.book Seite 185 Donnerstag, 9. April 2009 3:33 15

186
Driving and Driving Safety Collapsible spare wheel
fNever switch the PSM off when driving with a
collapsible spare wheel.
To w i n g
fFor information on towing:
Please see the chapter “TOWING” on
Page 342.
Tip on driving
When PSM is switched off, wheel-specific brake
interventions and the traction control system
(TCS) are also inactive.
The automatic brake differential (ABD) remains on.
Switching PSM back onfPress PSM OFF button A.
PSM is switched on after a short delay.
The light-emitting diode in the button and the
multi-functional PSM light on the instrument
panel go out. A message is shown on the multi-
purpose display of the instrument panel.
ABS
(Anti-lock Brake System)
Warning!
In spite of the advantages of ABS, it is still the
driver’s responsibility to adapt her/his driving style
and maneuvers in line with road and weather
conditions, as well as the traffic situation.
The increased safety that is provided should not
induce you to take greater risks with your safety.
The limits set by the physics of driving cannot be
overcome, even with ABS.
Risks of accident due to inappropriate speed can-
not be reduced by ABS.
ABS ensures:
–Full steering control
The vehicle remains steerable
–Good driving stability
No skidding due to locked wheels
–Optimum braking distance
Shorter stopping distances in most cases
–Lock prevention
No flat spots on the tiresFunction
The decisive advantage of ABS is in the driving
stability and maneuvrability of the vehicle in
hazardous situations.
ABS prevents locking of the wheels during full
braking, on almost all road surfaces, until shortly
before the vehicle stops.
The ABS begins to control the braking process as
soon as a wheel shows a tendency to lock.
This controlled braking process is comparable to
extremely rapid cadence braking.
The pulsating brake pedal and a “rattling noise”
warn the driver to adapt her/his driving speed to
the road conditions.
fIf full braking should be necessary, press the
brake pedal all the way down throughout the
entire braking procedure, regardless of the
pulsating pedal. Do not ease up on pressure
applied to the pedal.
10_Cayenne_21_KW17.book Seite 186 Donnerstag, 9. April 2009 3:33 15

Driving and Driving Safety
187
Warning light
If the ABS warning lights light up in the instrument
panel and on the multi-purpose display of the
instrument panel while the engine is running, the
ABS has switched off because of a fault.
In this event, the braking system will operate with-
out lock prevention,as in cars without ABS.
fAdapt your driving style to the changed
braking behavior.
fThe ABS must be checked immediately at an
authorized Porsche dealer. This is necessary
in order to prevent the occurrence of further
faults whose effects cannot be defined.
The ABS control unit is adjusted for the approved
tire dimensions.
The use of tires with non-approved dimensions can
lead to different wheel speeds, causing the ABS to
switch off.
Off-road ABS
(ABS in Low Range program)
When Low Range is active, an ABS specially
matched to off-road driving is activated automati-
cally.In the event of braking on loose ground, the per-
missible slip values for ABS braking are increased
so that the off-road braking distance is reduced
(wheels dig into the surface).
If the driver needs to steer, this off-road driving
program is automatically switched off to maintain
steerability.
Hillholder -
moving-off assistant on vehicles with
Tiptronic SIn Tiptronic selector lever positions D and M, the
hillholder function makes it easier to move off
from a standstill on an upward slope when the
engine is running. The driver does not have to
apply the brake.
The hillholder thus makes moving off on slopes
easier.
Danger!
Risk of accident, resulting in serious perso-
nal injury or death.
The vehicle can roll backwards if the Hillhol-
der is switched off.
fAlways apply the footbrake on slopes.Hillholder is not active:
– In Tiptronic selector lever positions N and R
– In the limp-home mode and
– If not all of the wheels are touching the ground
(on difficult terrain, for example).
Warning!
In spite of the advantages of the hillholder func-
tion, it is still the driver’s responsibility to adapt
her/his driving style and maneuvers in line with
situational conditions.
The increased safety that is provided should not
induce you to take greater risks with your safety.
The limits set by the physics of driving cannot be
overcome, even with the hillholder function.
Driving at the limits should be avoided, e.g., on icy
slopes or on slippery surfaces. In this and similar
cases, the support of the hillholder function is not
guaranteed.
10_Cayenne_21_KW17.book Seite 187 Donnerstag, 9. April 2009 3:33 15

192
Driving and Driving Safety Indication of selected level
The selected level is displayed by light-emitting
diodes beside the rocker switch (illustration).
The corresponding light-emitting diode beside the
rocker switch flashes during the control process.
The light-emitting diode is continuously lit after the
control process.
The level change is also indicated on the multi-
purpose display of the instrument panel.
Exceptions
Automatic changes from normal level to low level
and back are not indicated on the multi-purpose
display of the instrument panel.
Warning messageVarious messages are indicated on the multi-pur-
pose display of the instrument panel if there is a
system fault or if the compressor switches off due
to overload.
fFor further information on warning messages
on the multi-purpose display:
Please see the chapter “OVERVIEW OF
WARNING MESSAGES” on Page 149.
fAdapt your driving style to the changed condi-
tions.
fConsult an authorized Porsche dealer in order
to remedy a system fault.
fIf the overload-protection function causes the
compressor to switch off, wait for a time until
it has cooled down. The system will function
again as soon as it has cooled sufficiently.
The warning message appears when the control
system is switched off and when the collapsible
spare wheel is being filled. This does not indicate
a fault.
The warning message will go out once these
procedures have been completed.
Raising vehicle with the jackWhenever it is necessary to jack up the vehicle:
fManually set normal level and then switch off
level control.
Switching off level control
1. Switch ignition on.
2. Push rocker switch forward for 5 to
10 seconds.
A message is shown on the multi-purpose
display of the instrument panel.
The vehicle can now be raised.
Switching level control back on
1. Switch ignition on.
2. Push rocker switch forward for 5 to
10 seconds or
3. Drive forward with the vehicle.
Level control switches on automatically.Transporting the vehicles on car trains,
ferries and car transportersfTie the vehicle down only at its wheels.
10_Cayenne_21_KW17.book Seite 192 Donnerstag, 9. April 2009 3:33 15

Driving and Driving Safety
193
Porsche Active Suspension
Management (PASM)Various messages are shown on the multi-purpose
display of the instrument panel.
fFor further information on warning messages
on the multi-purpose display:
Please see the chapter “OVERVIEW OF
WARNING MESSAGES” on Page 149.
Three different running-gear setups can be selec-
ted with the push of a button:
–comfort
–normal
–sport
If the running-gear setups “comfort” or “normal”
have been selected, the system automatically
changes the setup to “sport” when the car is dri-
ven in a sporty manner.
Indication of the selected running-gear
setupThe light-emitting diode in the button of the selec-
ted running-gear setup is lit.
In addition, the selected running-gear setup is indi-
cated on the multi-purpose display of the instru-
ment panel for around 12 seconds.
The warning light in the instrument panel comes
on if there is a system fault. A warning message is
shown on the multi-purpose display of the instru-
ment panel.
fAdapt your driving style to the changed condi-
tions.
fTo remedy the fault, consult an authorized
Porsche dealer.
Selecting the running-gear setup1. Switch ignition on.
2. Press the appropriate button.
Note on operation
The running-gear setup selected last is stored in
memory after the ignition is switched off.
Warning lights and warning
messages
10_Cayenne_21_KW17.book Seite 193 Donnerstag, 9. April 2009 3:33 15

194
Driving and Driving Safety
Porsche Dynamic
Chassis Control (PDCC)FunctionPorsche Dynamic Chassis Control (PDCC) is a sys-
tem for roll stabilization of the vehicle body when
driving. Driving comfort and driving safety are im-
proved by active intervention of the anti-roll bars
on the front and rear axles.
No separate controls are available for the PDCC
system.
After selection of a running-gear setup in Porsche
Active Suspension Management (PASM):
–comfort
–normal
–sport
PDCC automatically activates the corresponding
on-road driving program.
fFor information on selecting a running-gear
setup:
Please see the chapter “PORSCHE ACTIVE
SUSPENSION MANAGEMENT (PASM)” on
Page 193.
PDCC automatically activates the off-road driving
program if Low Range reduction is switched on.fFor information on switching Low Range
reduction on and off:
Please see the chapter “DRIVING PROGRAMS
FOR ON-ROAD AND OFF-ROAD DRIVING” on
Page 177.
Warning messageA warning message appears on the multi-purpose
display of the instrument panel if there is a system
fault.
fFor further information on warning messages
on the multi-purpose display:
Please see the chapter “OVERVIEW OF
WARNING MESSAGES” on Page 149.
fAdapt your driving style to the changed
conditions.
fConsult an authorized Porsche dealer in order
to remedy the fault.
Checking hydraulic fluidRegular checking and changing of the hydraulic
fluid takes place as part of servicing.
Further important information on “Maintenance”
can be found in a separate chapter.
fPlease see the chapter “CAR CARE
INSTRUCTIONS” on Page 270.
10_Cayenne_21_KW17.book Seite 194 Donnerstag, 9. April 2009 3:33 15

Luggage Compartment, Loadspace and Storage
221
iPod, USB and AUXThe iPod, USB and AUX interfaces are located in
the storage box between the front seats.
Note
Do not leave your iPod, USB storage device or an
external audio source in the vehicle for extended
periods of time because extreme ambient conditi-
ons (temperature fluctuations, humidity) can occur
in the vehicle.
iPodUse the supplied connecting cable to connect one
of the iPod models listed:
– iPod 4th generation,
– iPod 5th generation,
– iPod nano,
– iPod nano 2nd generation,
–iPod mini,
– iPod photo or
– more modern iPod models (the operation of
more modern iPods cannot be guaranteed on
PCM).
fPlease refer to the section “iPod” in the sepa-
rate PCM operating instructions.
USBYou can connect a USB storage device to the USB
interface.
Yo u c a n
– play audio data (supported formats: MP3,
WMA and AAC-LC),
– download data from the Sport display and
– download data from the PCM logbook.
fPlease refer to the section “USB” in the sepa-
rate PCM operating instructions.
Note
The LED display of a standard USB storage device
is turned away from the driver when connected to
the USB interface.AUX
External audio sourceYou can connect an external audio source to the
AUX interface. This external audio source is then
operated on the audio source rather than on the
PCM or radio system.
fPlease refer to the section “External audio
source” in the separate PCM or radio opera-
ting instructions.
10_Cayenne_21_KW17.book Seite 221 Donnerstag, 9. April 2009 3:33 15

Parking
239
A- Front display – left monitoring area
B- Front display – right monitoring areaWarning indicators, signal tones, distances
The warning indicator for the front area is located
on the dashboard.
The warning indicator for the rear area is located
in the rooflining at the rear of the loadspace.
The warning indicators for the various monitoring
areas (left and right) are subdivided respectively
into one green, 4 yellow and 2 red light segments
C- Rear display – right monitoring area
D- Rear display – left monitoring areaIf ParkAssist is activated, the green light seg-
ments of the active warning indicators are lit up
continuously.
If the vehicle approaches an obstacle that has
been detected by the sensors, one or more of the
yellow or red light segments lights up, depending
on the distance to the obstacle.If the first yellow light segment lights up, the
obstacle is still 48 in. (120 cm) (to the front) or
48 in. to 59 in. (120 to 150 cm) (to the rear)
away.
A brief signal tone sounds when reversing.
An intermittent tone sounds when the distance
becomes less than approx. 24 in. (60 cm). The
fourth yellow light segment lights up.
A continuous tone sounds when the distance be-
comes less than approx. 10 in. (25 cm) (on vehic-
les with trailer coupling: approx. 14 in. (35 cm)).
The second red light segment lights up.
If the obstacle is approached even closer, the
system may not be able to recognize the obstacle
any longer.
fSet the radio volume so that the signal tones
are not drowned out.
You can have the volume of the signal tones
adjusted to your own requirements at your
authorized Porsche dealer.
Note on operation
If the obstacle is approached even closer after the
continuous tone sounds and the second red light
segment lights up, the system may not be able to
recognize the obstacle any longer.
10_Cayenne_21_KW17.book Seite 239 Donnerstag, 9. April 2009 3:33 15

246
Alarm System and Theft Protection
Switching onfLock the vehicle.
The alarm system and passenger compart-
ment monitoring system are switched on.
fPlease see the chapter “UNLOCKING AND
LOCKING FROM OUTSIDE” on Page 19.Switching offfUnlock the vehicle.
The alarm system and passenger compart-
ment monitoring system are switched off auto-
matically.
Note on operation
If you unlock the vehicle with the key at the door
lock, you must switch the ignition on (ignition lock
position 1) within 15 seconds of opening the door
in order to prevent the alarm system from being
triggered.
Temporarily deactivating passenger
compartment monitoring systemIf people or animals are remaining in the locked
vehicle or the vehicle is being transported on a
passenger train or ship, for example, the passen-
ger compartment monitoring system must be
deactivated.
When locked again, the passenger compartment
monitoring is activated again. The rocker switch to switch off the passenger
compartment monitoring system is located next
to the driver's seat under the seat belt height ad-
justment.
Note on operation
You can also temporarily deactivate the passen-
ger compartment monitoring system on the multi-
purpose display in the instrument panel:
fPlease see the chapter “SWITCHING OFF PAS-
SENGER COMPARTMENT MONITORING ON
THE MULTI-PURPOSE DISPLAY” on Page 142.
10_Cayenne_21_KW17.book Seite 246 Donnerstag, 9. April 2009 3:33 15