towing RAM CHASSIS CAB 2007 Service Manual

Recreational Towing Procedure — Manual Shift
Transfer Case — If Equipped
Use the following procedure to prepare your vehicle for
recreational towing:
CAUTION!It is necessary to follow these steps to be certain that
the transfer case is fully in N (NEUTRAL) before
recreational towing to prevent damage to internal
parts.
1. Bring the vehicle to a complete stop.
2. Shut OFF the engine.
3. Depress the brake pedal.
4. Shift automatic transmission to N (NEUTRAL), or
depress the clutch on manual transmissions. 5. Shift transfer case lever into N (NEUTRAL).
6. Start the engine.
7. Shift automatic transmission into Reverse (R).
8. Release brake pedal for five seconds and ensure that
there is no vehicle movement.
9. Repeat steps 7 and 8 with the transmission in Drive
(D).
10. Shut OFF the engine and place the ignition key to the
unlocked OFF position.
11. Shift automatic transmission into P (PARK).
12. Apply the parking brake.
13. Attach vehicle to tow vehicle with tow bar.
14. Release the parking brake. STARTING AND OPERATING 361
5

CAUTION!• Do not use a bumper mounted clamp-on tow bar
on your vehicle. The bumper face bar will be
damaged.
• Do not disconnect the rear driveshaft because
fluid will leak from the transfer case and damage
the internal parts.
Recreational Towing Procedure — Electronic Shift
Transfer Case — If Equipped
Use the following procedure to prepare your vehicle for
recreational towing. CAUTION!It is necessary to follow these steps to be certain that
the transfer case is fully in Neutral (N) before
recreational towing to prevent damage to internal
parts.
1. Bring vehicle to a complete stop.
2. Shut OFF the engine.
3. Turn the ignition key to the ON position, but do not
start the engine.
4. Depress the brake pedal.
5. Shift automatic transmission to Neutral (N) or depress
clutch on manual transmission. STARTING AND OPERATING 363
5

WHAT TO DO IN EMERGENCIESCONTENTS
Hazard Warning Flasher ..................370

Jacking And Tire Changing ................371
▫ All Models ..........................371

Jacking Instructions .....................372
▫ Tire Changing Procedure ................372

Hoisting .............................381

Jump-Starting .........................382 ▫ With Portable Starting Unit ..............385

Freeing A Stuck Vehicle ..................385

Emergency Tow Hooks — If Equipped ........386

Towing A Disabled Vehicle ................387
▫ 4-Wheel- Drive Vehicles .................387
▫ 2–Wheel- Drive Vehicles ................388
6

wheel. The nuts should then be tightened to recom-
mended torque. Tighten the nuts to final torque in
increments. Progress around the bolt circle, tightening
the nut opposite to the nut just previously tightened until
final torque is achieved. Recommended torques are
shown in the following chart.
Disc
Wheels Type Nut Stud Size Torque
Ft. Lbs. Torque
Newton
Meters
Cone 9/16-18 120-150 160-200
Flanged 9/16-18 130-160 190-220
To Stow The Flat Or Spare (If equipped)
Refer to Upfitters Body Builders Guide for information
on stowing your spare tire (If equipped). HOISTING
A conventional floor jack may be used at the jacking
locations, refer to the graphics that show jacking loca-
tions. However, a floor jack or frame hoist must never be
used on any other parts or the underbody.
CAUTION!Never use a floor jack directly under the differential
housing of a loaded truck or damage to your vehicle
may result. WHAT TO DO IN EMERGENCIES 381
6

CAUTION!Tow hooks are for emergency use only, to rescue a
vehicle stranded off road. Do not use tow hooks for
tow truck hookup or highway towing. You could
damage your vehicle.
TOWING A DISABLED VEHICLE
Proper towing or lifting equipment is required to prevent
damage to your vehicle. Use only tow bars and other
equipment designed for the purpose, following equip-
ment manufacturer’s instructions. Use of safety chains is
mandatory. Attach a tow bar or other towing device to
the main structural members of the vehicle—not to
bumpers or associated brackets. State and local laws
applying to vehicles under tow must be observed. 4-Wheel- Drive Vehicles
CAUTION!To avoid damage to the transfer case while towing,
always use one of the following methods.
NOTE: The Transfer Case must be in the neutral posi-
tion, and the transmission must be in Park (Automatic
Transmission), or in gear (Manual Transmission) to tow a
4WD vehicle with one end of the vehicle raised. WHAT TO DO IN EMERGENCIES 387
6

The manufacturer recommends towing with all wheels
OFF the ground. Acceptable methods are to tow vehicle
on a flatbed or with one end of vehicle raised and the
opposite end on a towing dolly. 2–Wheel- Drive Vehicles
Provided that transmission is operable, tow on a flatbed
or with the front wheels raised and the rear wheels on a
dolly.388 WHAT TO DO IN EMERGENCIES

ONBOARD DIAGNOSTIC SYSTEM (OBD II)
Vehicles equipped with California emissions controls
have a sophisticated onboard diagnostic system called
OBDII. This system monitors the performance of the
emissions, engine, and automatic transmission control
systems. When these systems are operating properly,
your vehicle will provide excellent performance and fuel
economy, as well as engine emissions well within current
government regulations.
If any of these systems require service, the OBD II system
will turn on the “Malfunction Indicator Light.” It will
also store diagnostic codes and other information to
assist your service technician in making repairs. Al-
though your vehicle will usually be driveable and not
need towing, see your dealer for service as soon as
possible. CAUTION!Prolonged driving with the “Malfunction Indicator
Light” on could cause further damage to the emis-
sion control system. It could also affect fuel economy
and driveability. The vehicle must be serviced before
any emissions tests can be performed.
If the “Malfunction Indicator Light” is flashing,
severe catalytic converter damage and power loss
will soon occur. Immediate service is required.
Loose Fuel Filler Cap Message
If the vehicles diagnostic system determines that the fuel
filler cap in loose, improperly installed, or damaged, a
GASCAP message will be displayed in the instrument
cluster. Tighten the gas cap until a “clicking” sound is
heard. This is an indication that the gas cap is properly
tightened. Press the odometer reset button to turn the394 MAINTAINING YOUR VEHICLE

Change Engine Oil (Gas Engines)
Road conditions as well as your kind of driving affect the
interval at which your oil should be changed. Check the
following to determine if any apply to you:
• Frequent short trips where the engine does not achieve
full operating temperature (operating temperature de-
fined as 190° F (66° C ) coolant temperature).
• Extensive engine idling (over 10 minutes per hour of
operation) at ambient temperatures less than 32° F (0°
C).
• Driving in dusty conditions.
• Frequent trailer towing.
• Taxi, police, or delivery service (commercial service).
• Off-road or desert operation.
• Extensive operation at high engine speeds (greater
than 2900 rpm) and loads (greater than 70% throttle). If ANY of these apply to you, then change your engine oil
at every interval shown in schedule  B  of the  Mainte-
nance Schedules  section of this manual.
If none of these apply to you, then change your engine oil
at every interval shown on schedule  A  of the  Mainte-
nance Schedules  section of this manual.
NOTE: Most vehicles are operated under the conditions
listed for Schedule  B. 
Dusty Conditions
Driving through dust-laden air increases the problems of
keeping abrasive materials out of the engine. Under these
conditions, special attention should be given to the
engine air cleaner, the crankcase inlet air cleaner and the
crankcase ventilation system. Make sure that these units
are clean at all times. This will tend to reduce to a
minimum the amount of abrasive material that may enter
the engine.400 MAINTAINING YOUR VEHICLE

• Do not shut off the engine or interrupt the ignition
when the transmission is in gear and the vehicle is in
motion.
• Do not try to start engine by pushing or towing the
vehicle.
• Do not idle the engine with any spark plug wires
disconnected or removed, such as when diagnostic
testing, or for prolonged periods during very rough
idling or malfunctioning operating conditions.
Intervention Regeneration Strategy – EVIC
Message Process Flow (Catalyst Full Message)
(Diesel Engines Only)
Your new Cummins 6.7L diesel meets all EPA Heavy
Duty Diesel Engine Emissions Standards for 2007 MY
(HDDE07), resulting in the lowest emitting diesel engine
ever produced. To achieve these emission standards your Dodge Chassis
Cab truck is equipped with state of the art engine and
exhaust system. The engine and exhaust aftertreatment
system work together to achieve the HDDE07 standard.
These systems are seamlessly integrated into your Dodge
truck and managed by the Cummins 6.7L engine Power-
train Control Module (PCM). The PCM manages engine
combustion to allow the exhaust system’s catalyst to trap
and burn Particulate Matter (PM) pollutants, with no
input or interaction on your part.
Additionally, the overhead console in your Dodge truck
has the ability to alert you to additional maintenance
required on your truck or engine. Refer to the following
messages that may be displayed on your Electronic
Vehicle Information Center (EVIC): MAINTAINING YOUR VEHICLE 415
7

reference holes when the transmission reaches 180° F (21°
C). Remember it is best to check the level at the normal
operating temperature.
CAUTION!Be aware that if the fluid temperature is below 50° F
(10° C), it may not register on the dipstick. Do not
add fluid until the temperature is elevated enough to
produce an accurate reading.
7. Check for leaks. Release the Parking Brake.
NOTE: To prevent dirt and water from entering the
transmission after checking or replenishing fluid, make
certain that the dipstick cap is properly reseated. It is
normal for the dipstick cap to spring back slightly from
its fully seated positions, as long as its seal remains
engaged in the dipstick tube. Automatic Transmission Fluid and Filter Change
The fluid and filter(s) should be changed and the as
specified in the Maintenance Schedule (Section 8). Ve-
hicles having severe usage should follow Maintenance
Schedule “B” of the Maintenance Schedule (Section 8).
Severe usage consists of:
• Off-the-highway operation;
• Trailer towing;
• Snow plow operation;
• Prolonged operation with heavy loading, especially in
hot weather.
NOTE: If the transmission is disassembled for any
reason, the fluid and filter should be changed, and the
bands adjusted (if equipped).440 MAINTAINING YOUR VEHICLE