service RAM CHASSIS CAB 2007 Repair Manual

WARNING!Worn brake hoses can burst and cause brake failure.
You could have an accident. If you see any signs of
cracking, scuffing, or worn spots, have the brake
hoses replaced immediately.
Brake Master Cylinder – Brake Fluid Level Check
The fluid level of the master cylinder should be checked
when performing under the hood service, or immedi-
ately if the brake system warning lamp indicates system
failure.
The brake master cylinder has a translucent plastic
reservoir. On the outboard side of the reservoir, there is a
“FULL” dot and an “ADD” dot. The fluid level must be
kept within these two dots. Do not add fluid above the
full mark because leakage may occur at the cap. With disc brakes the fluid level can be expected to fall as
the brake linings wear. However, an unexpected drop in
fluid level may be caused by a leak and a system check
should be conducted.
Refer to Fluids, Lubricants and Genuine Parts for the
correct Fluid type.
WARNING!Use of a brake fluid that may have a lower initial
boiling point, or unidentified as to specification,
may result in sudden brake failure during hard
prolonged braking. You could have an accident. MAINTAINING YOUR VEHICLE 435
7

WARNING!Overfilling the brake fluid reservoir can result in
spilling brake fluid on hot engine parts and the
brake fluid catching fire.
Use only brake fluid that has been in a tightly closed
container to avoid contamination from foreign matter or
moisture.
CAUTION!Do not allow a petroleum-base fluid to contaminate
the brake fluid. Seal damage and loss of brake
performance may result. Clutch Hydraulic System
The clutch hydraulic system is a sealed maintenance-free
system. In the event of leakage or other malfunction, the
system must be replaced.
Clutch Linkage
If the clutch pedal linkage begins to squeak or grunt, the
clutch pedal pivot bushings should be lubricated. Refer
to Fluids, Lubricants and Genuine Parts for the correct
lubricant type. Multipurpose Grease, NLGI Grade 2 E.P.
Rear Axle And 4x4 Front Driving Axle Fluid Level
For Model 9.25 Front Axles and 11.5” Rear Axles refer to
Fluids, Lubricants and Genuine Parts for the correct
lubricant type. For normal service, periodic fluid level
checks are not required. When the vehicle is serviced for
other reasons, the exterior surfaces of the axle assembly
should be inspected.436 MAINTAINING YOUR VEHICLE

When checking the fluid level, the vehicle should be in a
level position. The fluid level should be 1/4” ± 1/4” (6.4
mm ± 6.4 mm) below the fill hole on the 9.25” Front Axle.
The fluid level should be 3/4” ± 1/4” (19 mm ± 6.4 mm)
below the fill hole on 11.5” Rear Axles.
Drain And Refill
Vehicles operated in normal service do not have regularly
scheduled oil changes. If fluid has become contaminated
with water or subjected to severe service, follow the
recommended change intervals in Maintenance Schedule
“B” in Section 8 of this manual.
Lubricant Selection
Refer to Fluids, Lubricants and Genuine Parts for the
correct lubricant type.
NOTE: The presence of water in the gear lubricant will
result in corrosion and possible failure of differential components. Operation of the vehicle in water, as may be
encountered in some off-highway types of service, will
require draining and refilling the axle to avoid damage.
Limited-Slip Differentials in vehicles equipped with
11.5” Axles DO NOT REQUIRE any limited slip oil
additive (friction modifiers).
Transfer Case — If Equipped
Lubricant Selection
Refer to Fluids, Lubricants and Genuine Parts for the
correct lubricant type.
Fluid Level Check
This fluid level can be checked by removing the filler
plug. The fluid level should be to the bottom edge of the
filler plug hole with the vehicle in a level position. MAINTAINING YOUR VEHICLE 437
7

the fluid level is correctly established at room tempera-
ture, it should be between the HOT (upper) reference
holes when the transmission reaches 160° F - 175° F (70°
C – 82° C). Remember it is best to check the level at the
normal operating temperature.
CAUTION!Be aware that if the fluid temperature is below 50° F
(10° C), it may not register on the dipstick. Do not
add fluid until the temperature is elevated enough to
produce an accurate reading. Never use any ATF
other than Mopar  AS68RC™ Automatic Transmis-
sion Fluid.
8. Check for leaks. Release the Parking Brake.
NOTE: To prevent dirt and water from entering the
transmission after checking or replenishing fluid, make certain that the dipstick cap is properly reseated. It is
normal for the dipstick cap to spring back slightly from
its fully seated positions, as long as its seal remains
engaged in the dipstick tube.
Automatic Transmission Fluid and Filter Change
To obtain best performance and long life for automatic
transmissions, the manufacturer recommends that they
be given regular maintenance service by an Authorized
Dodge Dealer or Service Center. It is important that the
transmission be adjusted periodically, the fluid main-
tained at the correct level, and that it be drained and
refilled as specified.
It is important that proper lubricant is used in the
transmission. Refer to Fluids, Lubricants and Genuine
Parts for the correct lubricant type. A band adjustment
and filter change should be made at the time of the oil
change. MAINTAINING YOUR VEHICLE 443
7

Rear Wheel Bearings — Manufacturer’s Axles
These bearings are normally considered permanently
lubricated. Cleaning and repacking is required only
when axle shafts are removed or in case of extreme water
or dust contamination.
Noise Control System Required Maintenance &
Warranty
For 3500 Two-Wheel Drive and Four-Wheel Drive mod-
els over 10,000 lbs. (4 535 kg) Gross Vehicle Weight
Rating.
All vehicles built over 10,000 lbs. (4 535 kg) Gross Vehicle
Weight Rating and manufactured for sale and use in the
United States are required to comply with the Federal
Government’s Exterior Noise Regulations. These vehicles
can be identified by the Noise Emission Control Label
located in the operator’s compartment. Required Maintenance For Noise Control Systems
The following maintenance services must be performed
every 6 months or 6,000 miles (9 600 km) whichever
comes first, to assure proper operation of the noise
control systems. In addition, inspection and service
should be performed anytime a malfunction is observed MAINTAINING YOUR VEHICLE 445
7

or suspected. Proper maintenance of the entire vehicle
will help the effectiveness of the noise control systems.
Exhaust System
Inspect the entire exhaust system for leaks and damaged
parts. Devices such as hangers, clamps, and U-bolts
should be tight and in good condition. Damaged compo-
nents, burned or blown out mufflers, burned or rusted
out exhaust pipes should be replaced according to the
procedures and specifications outlined in the appropriate
service manual.
Air Cleaner Assembly
Inspect air cleaner housing for proper assembly and fit.
Make certain that the air cleaner is properly positioned
and that the cover is tight. Check all hoses leading to the air cleaner for tightness. The air filter element must also
be clean and serviced according to the instructions out-
lined in the Maintenance Schedule Section of this
manual.
Tampering With Noise Control System Prohibited
Federal law prohibits the following acts or the causing
thereof: (1) the removal or rendering inoperative by any
person, other than for purposes of maintenance, repair, or
replacement, of any device or element of design incorpo-
rated into any new vehicle for the purpose of noise
control prior to its sale or delivery to the ultimate
purchaser or while it is in use, or (2) the use of the vehicle
after such device or element of design has been removed
or rendered inoperative by any person.446 MAINTAINING YOUR VEHICLE

Noise Systems Maintenance Chart and Service Log Maintenance Log and Service Chart (Gas Engines)
Insert
Month, Day, Year under column mileage closest to the mileage at which service was performed.
MILES 6,000 12,000 18,000 24,000 30,000 36,000 42,000 48,000
KILOME-
TERS 9 600 19 000 29 000 36 000 48 000 58 000 67 000 77 000
Exhaust
system-
inspect
Air cleaner
assembly-
inspect
ODOM-
ETER
READING
PER-
FORMED
BY
PER-
FORMED
AT 448 MAINTAINING YOUR VEHICLE

Noise Systems Maintenance Chart and Service Log Maintenance Log and Service Chart (Gas Engines)
Insert
Month, Day, Year under column mileage closest to the mileage at which service was performed.
MILES 54,000 60,000 66,000 72,000 78,000 84,000 90,000 96,000
KILOME-
TERS 87 000 96 000 106 000 116 000 126 000 135 000 145 000 154 000
Exhaust
system-
inspect
Air cleaner
assembly-
inspect
ODOM-
ETER
READING
PER-
FORMED
BY
PER-
FORMED
AT MAINTAINING YOUR VEHICLE 449
7

Maintenance Log and Service Chart (Diesel Engines)
Noise Systems Maintenance Chart and Service Log — Insert Month, Day, Year under column mileage closest to
the mileage at which service was performed.
MILES 7,500 15,000 22,500 30,000 37,500 45,000 52,500 60,000
KILOME-
TERS 12 000 24 000 36 000 48 000 60 000 72 000 84 000 96 000
Exhaust
system-
inspect
Air cleaner
assembly-
inspect
ODOM-
ETER
READING
PER-
FORMED
BY
PER-
FORMED
AT 450 MAINTAINING YOUR VEHICLE

Noise Systems Maintenance Chart and Service Log — Insert Month, Day, Year under column mileage closest to
the mileage at which service was performed.
MILES 67,500 75,000 82,500 90,000 97,500 84,000 105,00 112,500
KILOME-
TERS 108 000 120 000 132 000 144 000 126 000 156 000 168 000 181 000
Exhaust
system-
inspect
Air cleaner
assembly-
inspect
ODOM-
ETER
READING
PER-
FORMED
BY
PER-
FORMED
AT MAINTAINING YOUR VEHICLE 451
7