Display RENAULT CLIO 2003 X65 / 2.G Owners Manual

23HM
1
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T1.WIN 4/11/2002 13:45-page45
1.37
CLOCK / EXTERNAL TEMPERATURE
Clock1- setting the clock
With the ignition on, press button:
HFor hours,
MFor minutes.
Clock3, setting the time
With the engine switched on,
display3set to total mileage
recorder and clock function, press
and hold button2, to access time
setting mode, then release the
button.
There are two ways to set the time:
- one long press on button2allows
you to scroll through the hours
and minutes quickly;
- short presses on button2allow
you to set the time minute by
minute.If the electrical supply is cut
(battery disconnected, feed wire
broken, etc.), the clock must be
reset.
For your safety, we recommend
that you do not reset or alter the
time while driving.
External temperature
display1
The formation of ice is
related to exposure, local
hygrometry and temperature.
The external temperature alone is
not sufficient to detect ice.

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T1.WIN 4/11/2002 13:45-page47
1.39
DRIVER’S LAYOUT, LEFT HAND DRIVE(continued)
The equipment fitted, described below, depends on the version, option and country.
1Demister outlet for left-hand
side window
2Left-hand side vent
3Stalk for:
• direction indicators,
• exterior lights,
• front fog lights,
• rear fog lights,
• horn.
4Instruments.
5• Driver's airbag location.
• Horn
6Radio satellite controls.
7• Stalk for windscreen and rear
screen wash/wipe.
• Trip computer information
scrolling control.
8Centre air vents.9Display:
• Clock and temperature,
• Radio, clock and temperature
• Radio, clock, external
temperature and navigation
system
10Storage compartment.
11Passenger airbag location.
12Right-hand side air vent.
13Demister outlet for right-hand
side vent
14Glove box.
15Heated rear screen switch
16Hazard warning lights switch.
17Radio location or storage
compartment
18Air conditioning controls.19Ashtray and cigarette lighter
20Handbrake
21Gear lever
22Cup holder
23Electric door locking switch
24Ignition switch
25Cruise control/speed limiter
controls
26Steering wheel height adjuster
27Controls for:
• Electric headlight beam
adjustment
• Dimmer for control lighting
• Cruise control
• Electronic Stability Program
(ESP)
28Storage compartment
29Bonnet release
30Fuse box

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T1.WIN 4/11/2002 13:45-page49
1.41
DRIVER’S LAYOUT, RIGHT-HAND DRIVE(continued)
The equipment fitted, described below, depends on the version, option and country.
1Demister outlet for left-hand
side window
2Left-hand side vent
3Passenger airbag location.
4Storage compartment.
5Display:
• Clock and temperature,
• Radio, clock and temperature,
• Radio, clock, external
temperature and navigation
system
6Centre air vents.
7Stalk for:
• direction indicators,
• exterior lights,
• front fog lights,
• rear fog lights,
• horn.
8Instruments.
9• Driver's airbag location.
• Horn10Radio satellite controls
11• Stalk for windscreen and rear
screen wash/wipe
• On-board computer
information readout control
12Right-hand side vents
13Demister outlet for right-hand
side vent
14Controls for:
• Electric headlight beam
adjustment
• Instrument panel lighting
dimmer
• Cruise control and speed
limiter
• Electronic Stability Program
(ESP)
15Storage compartment
16Ignition switch
17Cruise control/speed limiter
controls
18Steering wheel height adjuster19Heated rear screen switch
20Hazard warning lights switch
21Cup holder
22Handbrake
23Gear lever
24Ashtray and cigarette lighter
25Heating and ventilation
controls
26Radiolocationorstorage
compartment
27Electric door locking switch
28Glove box
29Bonnet release
30Fuse box

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T1.WIN 4/11/2002 13:45-page53
1.45
INSTRUMENT PANEL(continued)
or
The presence and operation of the warning lights, described below, depend on the vehicle equipment and
country.
6Speed limiter and
cruise control indicator
light
To understand how this
operates, refer to the
information on the cruise
control and speed limiter
functions in Section 2.
Toxic fume monitoring
warning light
For vehicles equipped
with this option, the light
comes on when the ignition is
switched on then goes out.
•Ifitlightsuppermanently,
consult your Renault Dealer
as soon as possible;
• If it flashes, reduce the
engine speed until the light
stops flashing.
Consult your Renault Dealer
as soon as possible.
Refer to the information on
anti-pollution, fuel economy
and driving in Section 2.6Over-revving warning lightIndicates that you need
to change gear.
LPG mode operating
indicator
Refer to the LPG-powered
vehicles supplement.
7Multifunction display
Oil level display function
The vehicle must be parked on
level ground and the engine
shouldhavebeenswitchedoff
for some time beforehand to
obtain an accurate level
reading.
When the ignition has been
switched on for approximately
30 seconds:
-if the level is correct,the
display will show “oil OK”
- when the minimum oil level
is reached:the word “OK”
will no longer be displayed,
the dashes and the word
“Oil” will flash and the SERV
warning light will light up
until the engine is switched
off.
It is vital to top up as soon as
possible.7Total mileage recorder, trip
mileage and clock
Can be read approximately
30 seconds after the ignition is
switched on.
8Multifunction key
Press the key repeatedly to
select information on the
display, to reset the trip mileage
recorder or to set the clock.

1
3
2
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T1.WIN 4/11/2002 13:45-page58
1.50
ON-BOARD COMPUTER
1Display
2General reset and trip mileage
recorder reset button
To reset the trip mileage recorder,
the display must show the “trip
mileometer” function.
Automatic reset
Automatic resetting will occur
when the maximum of any of the
memories is exceeded.3Display selection key
Press button3repeatedly to
scroll through the following
information:
a) total mileage recorder,
b) trip mileage recorder,
c) fuel used,
d) average consumption,
e) current consumption,
f) estimated range,
g) distance covered,
h) average speed,
i) recommended speed (speed
limiter/cruise control).
Refer to the chart on the following
page for display examples.
Interpreting certain values
displayed after a reset:
The values showing average fuel
consumption, range and average
speed will become more stable
and reliable the further you travel
since the last time the reset key
was pressed.In the first few miles after resetting,
you may notice:
• that the range increases as you
drive. This is normal as the
average consumption may reduce
when:
- the vehicle is no longer
accelerating,
- the engine reaches normal
operating temperature (reset
when engine was cold),
- you drive from a built up area to
the open road.
If average consumption is
decreased, the expected range
will therefore increase.
• average consumption increases
when the vehicle is stationary
and idling.
This is normal as the computer
takes into account the fuel used
during idling.

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T1.WIN 4/11/2002 13:45-page59
1.51
ON-BOARD COMPUTER(continued)
Examples of
display selections by
pressing button3Interpreting the display
a) Total mileage recorder.
b) Trip mileage recorder.
c) Fuel used(in litres or gallons) since the last reset.
d) Average consumption(in mpg or l/100 km) since the last reset.
The value is displayed after covering 400 metres taking into account the
distance covered and the fuel used since the last reset.

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T1.WIN 4/11/2002 13:45-page60
1.52
ON-BOARD COMPUTER(continued)
Examples of
display selections by
pressing button3Interpreting the display
e) Current consumption(in mpg or litres/100 km)
The value is displayed after reaching a speed of 15 mph (25 km/h).
f) Estimated range with remaining fuel(in miles or km)
This function uses the average consumption since the last general reset.
The value is displayed after covering 400 metres.
g) Distance covered(in miles or km) since the last reset.
h) Average speed(in mph or km/h) since the last reset.
The value is displayed after covering 400 metres.
i) Cruise control or speed limiter recommended speed(depending on
vehicle).
See the information on speed limiter and cruise control in section 2.

A
B
C
1
F
G
H
I
E
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page10
2.10
PROACTIVE AUTOMATIC GEARBOX
Selector lever1
P:Park
R: Reverse
N: Neutral
D: Drive in automatic
(gears authorised: 1, 2, 3 and 4)
2: 2nd gear holdH
(gears authorised: 1, 2)
1: 1st gear holdH.
The displayEand indicator lightsF,
G,H,I, on the instrument panel
indicate the position of the gear
lever1and/or the operating mode of
the automatic gearbox.Position D3 or 3rd gear hold
(Gears authorised: 1, 2, 3).
With the selector lever in position
D, press buttonB. Indicator lightG
will light up on the instrument
panel. Press buttonBagain to
deselect this position. (indicator
lightwillgoout.)
Note:When indicator light is lit, the
system will prevent 4th gear being
selected.For safety reasons, certain positions
may not be selected until the
mechanism is released: press buttonA.
The lever may only be moved to D
or R when the vehicle is stationary,
with your foot on the brake and the
accelerator pedal released.
Moving off forwards
With the lever in position PorN,
switch on the ignition.
With your foot on the brake pedal,
move the lever out of positionPorN.
For safety reasons, to take the lever
out of position P, the brake pedal
must be pressed before pressing the
releasing buttonA.

1
4
3
5
2
6
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page13
2.13
QUICKSHIFT 5 GEARBOX
Selector lever
1Mode selection button: enables
you to move from manual mode to
automatic mode or from
automatic to manual mode at any
time with the engine running.
Note:The selector lever
automatically returns to the middle
position after use.Display
2automatic mode
3brake pedal depressed warning
light
4gear display
5not used
6gearbox fault warning light.
Thegearused(1,2..,5,N,R)is
indicated in the instrument panel
display. In automatic mode,(A)is
also displayed.
Driving
Switch on the ignition.
The display lights up on the
instrument panel.
As long as neutral is displayed (N),
start the engine but do not depress
the accelerator.
If a gear other than neutral(N)is
displayed this will flash;it will only
be possible to start the engine if you
press down the brake pedal (the
warning light3will come on if you
forget) when holding the key in
starting position.
The vehicle will then change to
neutral (N) automatically and the
engine will start.
Note: do not attempt to start the
engine by pushing the vehicle if the
battery is flat (the display remains
off when the ignition is switched
on).

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page14
2.14
QUICKSHIFT 5 GEARBOX(continued)
Starting up
Moving forwards(starting in
neutral)
The gear display showsNandA.
•With your foot on the brake
pedal, push the selector lever
toward the front and then release
it again.
• Release the brake pedal:
- it is possible to carry out parking
manoeuvres when the engine is
idling.
- accelerate gently to move off.
Note:you can pull away in second
gear if you are driving on slippery
surfaces (snow, mud, etc.).
To do this, move the gear selector
lever twice with your foot on the
brake pedal.
The figure2appears on the
dashboard display. The system is
then running in semi-automatic
mode.
To return to automatic mode, press
the mode change button.Reverse
• Foot on the brake pedal.Push the
lever as far as it will go to the
right, hold and pull back
according to the marking on the
knob, then release it. Reverse gear
is engaged and the letterR
appears on the display.
• Release the brake pedal:
- it is possible to carry out parking
manoeuvres when the engine is
idling.
- accelerate gently to reverse.
Note:You should put your foot on
the brake to engage or disengage a
gear when stopping. Otherwise, the
gear selected will flash and the
warning light3will come on.
Gear selection gate
+To move up through the gears
– To move down through the gears
NNeutral
RReverse
•Only stable lever position