RENAULT MEGANE COUPE CABRIOLET 2015 X95 / 3.G Owners Manual

5.29
TOWING: breakdown (1/2)
Before towing, unlock the steering
column: with the clutch depressed,
engage first gear (lever in position N
or R for vehicles with automatic trans-
missions), insert the RENAULT card in
the card reader then press the engine
start button for two seconds.
Reposition the lever to neutral (posi-
tion N for vehicles fitted with an auto-
matic gearbox).
The column is unlocked, the acces-
sory functions are supplied: the vehi-
cle lights can be used (indicators, brake
lights etc.). At night the vehicle must
have its lights on.
Once you have finished towing, press
the engine start button twice (risk of
running down the battery). The speed specified by current legisla-
tion for towing must always be obser-
ved. If your vehicle is the towing vehi-
cle, do not exceed the maximum towing
weight for your vehicle (refer to the in-
formation on “Weights” in Section 6).
Towing a vehicle with an
automatic gearbox
With the engine switched off, the trans-
mission is no longer lubricated. It is pre-
ferable to tow this type of vehicle on a
trailer or tow it with the front wheels off
the ground.
Under exceptional circumstances,

you may tow the vehicle with all four
wheels on the ground, only going
forward, with the gear lever in the N po-
sition, and for a distance not exceeding
50 miles (80 km).
If the lever is stuck in P ,
even though you are de-
pressing the brake pedal,
the lever can be released
manually. To do this, insert a rigid
rod in the hole 2, press the rod and
unlocking button 1 located on the
lever simultaneously.
1
2
Do not remove the
RENAULT card from the
reader when the vehicle is
being towed.

5.30
TOWING: breakdown (2/2)
Only use the front 3 and rear 6
towing points.
These towing points may only be used
for towing: never use them for lifting the
vehicle directly or indirectly.Access to towing points
Unclip cover 5 or 7 by sliding a flat tool
(or the key integrated in the RENAULT
card) under the cover.
Tighten the tow eye 4 fully: as much
as possible by hand at first, then finish
tightening it using the wheelbrace or,
depending on the vehicle, the lever.
Use only the tow eye 4 and the whee-
lbrace or the lever located under the
boot carpet in the tool kit (please refer
to the information under “Tools” in
Section 5).
When the engine is stop-
ped, steering and braking
assistance are not opera-
tional.Do not leave the tools unse-
cured inside the vehicle as
they may come loose under
braking.
– Use a rigid towing bar.
If a rope or cable is used
(where the law allows this),
the vehicle being towed
must be able to brake.
– A vehicle must not be towed if it is not fit to be driven.
– Avoid accelerating or braking suddenly when towing, as this
may result in damage being
caused to the vehicle.
– When towing a vehicle, it is ad- visable not to exceed 30 mph
(50 km/h).
– Do not push the vehicle if the steering column is locked.
3
4
54
7
6

5.31
OPERATING FAULTS (1/6)
The following advice will enable you to carry out quick, temporary repai\
rs. For safety reasons you should always contact
an approved dealer as soon as possible.
Using the RENAULT card POSSIBLE CAUSESWHAT TO DO
The RENAULT card does not
lock or unlock the doors. Card battery is flat.
Replace the battery. You can still lock/unlock and start
your vehicle (refer to the information on “Locking/un-
locking the doors” in Section 1 and “Starting/Stopping
the engine” in Section 2).
Use of appliances operating on
the same frequency as the card
(mobile phone, etc.). Stop using the equipment or use the integrated key
(refer to the information on “Locking/unlocking the
doors” in Section 1).
Vehicle located in a high electro-
magnetic radiation zone.
Vehicle battery flat. Use the key integrated in the card (refer to the in-
formation on “Locking/unlocking the doors” in
Section 1).
The vehicle is started. With the engine running, the card’s locking/unlocking
device is blocked. Turn off the ignition.

5.32
OPERATING FAULTS (2/6)
The starter is activatedPOSSIBLE CAUSES WHAT TO DO
The instrument panel indicator lights
are weak or fail to light up and the
starter does not turn. Battery terminals not tight,
battery terminals discon-
nected or oxidised.Retighten or reconnect the terminals, or clean them
if they are oxidised.
Discharged battery or not
operational. Connect another battery to the faulty battery. Refer to
information on “Battery: troubleshooting” in Section 5
or replace the battery if necessary.
Do not push the vehicle if the steering column is
locked.
Faulty circuit. Consult an approved dealer.
The engine will not start. Starting conditions are not
fulfilled.Please refer to the information on “Starting, stopping
the engine” in Section 2.
The hands-free RENAULT
card does not work. Insert the card in the card reader in order to start the
engine.
Please refer to the information on “Starting, stopping
the engine” in Section 2.
The engine cannot be switched off. Card not detected. Insert the card in card reader.
Electronic fault. Press the starter button quickly five times. The engine
can be restarted by pressing on the clutch pedal if the
Stop and Start function is activated.

5.33
OPERATING FAULTS (3/6)
On the roadPOSSIBLE CAUSES WHAT TO DO
The steering column remains
locked. Steering wheel locked.
Move the steering wheel while pressing the engine
start button (please refer to Section 2 “Starting/stop-
ping the engine”).
Faulty circuit. Consult an authorised dealer.
Coolant boiling in the coolant
reservoir. Mechanical fault: damaged cylin-
der head gasket. Stop the engine.
Contact an approved dealer.
Smoke under the bonnet. Short-circuit or cooling system
leak. Stop, switch off the ignition, stand away from the ve-
hicle and contact an approved dealer.
The oil pressure warning light
comes on: while cornering or braking The level is too low. Top up the engine oil level (refer to the information
on “Engine oil level: topping up/filling” in Section 4).
is slow to go out or remains lit
under acceleration Loss of oil pressure.
Stop the vehicle and contact an approved dealer.
White smoke from the exhaust. In the diesel version, this is nec-
essarily a fault. Smoke may be
caused by particle filter regenera-
tion. Please refer to the information on “Special features
of diesel versions” in Section 2.

5.34
OPERATING FAULTS (4/6)
On the roadPOSSIBLE CAUSES WHAT TO DO
Steering becomes heavy. Assistance overheating. Consult an approved dealer.
The engine overheats. The
coolant temperature indica-
tor is in the warning zone and
warning light
® comes on. Engine cooling fan not working. Stop the vehicle, switch off the engine and contact an
approved dealer.
Coolant leaks. Check the coolant reservoir: it should contain fluid.
If there is no coolant, consult an approved dealer as
soon as possible.
Vibrations. T yres not inflated to correct pres-
sures, incorrectly balanced or dam-
aged. Check the tyre pressures: if this is not the problem,
have them checked by an approved dealer.
Radiator:
If there is a significant lack of coolant, remember that it must never b\
e topped up using cold coolant while
the engine is very warm. After any procedure on the vehicle which has involved even partial drain\
ing of the cooling
system, it must be refilled with a new mixture prepared in the correct p\
roportions. Reminder: only products approved
by our Technical Department may be used for this purpose.

5.35
OPERATING FAULTS (5/6)
Electrical equipmentPOSSIBLE CAUSES WHAT TO DO
The wipers do not work. Wiper blades stuck. Free the blades before using the wipers.
Faulty electrical circuit. Consult an approved dealer.
The wiper does not stop. Faulty electrical controls. Consult an approved dealer.
Direction indicators flashing
more quickly. Blown bulb.
Front: contact an approved dealer.
Rear: replace the bulb.
The direction indicators do not
work. Faulty electrical circuit or control. Consult an approved dealer.
Fuse damaged.
Replace the fuse, refer to the information on “Fuses”.
The headlights do not switch
on or off. Faulty electrical circuit or control. Consult an approved dealer.
Fuse damaged.
Replace the fuse, refer to the information on “Fuses”.
Traces of condensation in the
lights. Traces of condensation may be a
natural phenomenon caused by var-
iations in temperature.
In this case, the traces will disappear
slowly once the lights are switched
on. The traces soon disappear when the lights are
switched on.

5.36
OPERATING FAULTS (6/6)
Electrical equipmentPOSSIBLE CAUSES WHAT TO DO
The roof will not open/close or
the roof opening/closing opera-
tion is interrupted. Sunroof opening/closing conditions
not fulfilled. The message “Roof: see
handbook” appears on the instru-
ment panel. Apply the opening/closing conditions (refer to the in-
formation on “Retractable glass roof” in Section 3).
Electrical or roof fault (discharged
battery, etc.).
The message “Check roof See
handbook” accompanied by the in-
dicator light
© appears on the
instrument panel. Close the sunroof, if open, using the method de-
scribed in “Retractable glass roof: Operating fault” in
Section 3 and contact your approved Dealer.

6.1
Section 6: Technical specifications
Vehicle identification plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . . . . . . . . . . . 6.2
Engine identification plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . . . . . . . . . . . . . . . . 6.3
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5
Engine specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . . . . . . . . . . . . . . . . 6.6
Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.7
Towing weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.7
Replacement parts and repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . . . . . . . . 6.8
Service sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.9
Anti-corrosion check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . . . . . . . . . . . . . . . . . . . . . 6.15

6.2
VEHICLE IDENTIFICATION PLATES
A
B
A
97
8
10
5
1
2
3
4
6
The information shown on the ve-
hicle identification plate should be
quoted on all correspondence or
orders.
The presence and location of the in-
formation depends on the vehicle.
Vehicle identification plate A
1 Manufacturer name.
2 EC design number or approval
number.
3 Identification number.
Depending on the vehicle, this
information is also given on
marking B.
4 MAM (Maximum Authorised
Mass).
5 GTW (Gross train weight: vehicle
fully loaded, with trailer).
6 MPAW (Maximim Permissible
Weight) for front axle.
7 MPAW on rear axle.
8 Reserved for related or additional
entries.
9 Diesel exhaust emissions.
10 Paint reference (colour code).