stop start RENAULT PULSE 2012 1.G Service Manual


> (GLW    0RGHO .$2(0B5HQDXOW @
HR12DE engine model (for Indonesia, Brunei,
Singapore) :km/h (MPH)
1st 39 (24)
2nd 72 (4\f)
3rd 10\f (66)
4th 143 (\b9)
\fth — (—)
HR12DE engine model (for Central and South
America, and Caribbean countries): km/h (MPH)
1st 39 (24)
2nd 71 (44)
3rd 10\f (6\f)
4th 133 (\b3)
\fth — (—)
HR12DDR engine model (for Europe): km/h (MPH)
1st 47 (29)
2nd \b6 (\f3)
3rd 127 (79)
4th 171 (106)
\fth — (—)K9K engine model:
km/h (MPH)
1st 36 (22)
2nd 6\f (41)
3rd 92 (\f7)
4th 126 (7\b)
\fth — (—)The Idling Stop System activates to prevent unneces-
sary fuel consumption, exhaust emissions and noise.
.
When you stop the vehicle, the engine is turned
off automatically.
. When you start the vehicle again, the engine is
turned on automatically.
CAUTION:
When the vehicle is moved with the engine
stopped by the system on a downhill grade
(approximately 2km/h or more) , depress the
brake pedal quickly because the engine restarts
automatically. This may lead to an accident.
NOTE:
Idling Stop System will not activate under the
following conditions
.when the engine is kept idling without any driving
after the engine is turned on.
. when the engine coolant temperature is low.
. when the battery capacity is low.
. when the battery temperature is low or extremely
high.
. when the vehicle is moved.
. when a negative pressure booster decreases.
. when the engine hood is opened with the engine
running.
. when the engine is turned on with the engine hood
open.
. when the steering wheel is operated.
. when Idling Stop System indicator blinks at a low
speed.
. when the accelerator pedal is depressed.
Starting and driving\f-19
IDLING STOP SYSTEM (if equipped
for Thailand)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-20Starting and driving
.when the selector lever is in the "R" (Reverse\f
position.
. when the rear \befogger is turne\b on.
. when the air con\bitioner is turne\b on.
. when the Electric power steering warning light or
the Anti-lock Braking System (ABS\f warning light
(if equippe\b\f illuminate.
. when the brake pe\bal is not \bepresse\b.
. when stopping the vehicle on sloping roa\bs.
. when the power consumption is large.
NOTE:
It may take some time until Idling Stop System
activates under the following conditions:
. when the battery is \bischarge\b.
. when the outsi\be temperature is low.
. when the battery is replace\b or the battery
terminal is \bisconnecte\b for exten\be\b perio\bs
an\b then reconnecte\b.
NOTE:
The engine will not restart with releasing the
brake pedal while Idling Stop System is acti-
vated under the following condition:
. when the selector lever is in the "P" (Park\f
position.
NOTE:
The engine will restart without releasing the
brake pedal while Idling Stop System is acti-
vated under the following conditions:
. when the rear \befogger is turne\b on.
. when the air con\bitioner is turne\b on.
. when the accelerator pe\bal is \bepresse\b. .
when the steering wheel is operate\b.
. when the battery capacity is low.
. when the power consumption is large.
. when the brake pe\bal is release\b on sloping roa\bs
an\b the vehicle is move\b.
. when the brake pe\bal is release\b with the selector
lever in the "D" (Drive\f or "N" (Neutral\f position.
. when the selector lever is place\b in the "L" (Low\f ,
"D" (Drive\f or "R" (Reverse\f position from the "N"
or "P" position.
. When the negative pressure of the brake system is
not sufficiently applie\b by \bepressing the brake
pe\bal several times.
Use this system while waiting at stoplight, etc. When
the vehicle is stoppe\b for long perio\bs of time, turn off
the engine.
When the engine hoo\b is opene\b with I\bling Stop
System on, the engine will be in the normal stoppe\b
state with the buzzer soun\bing. In this case, restart the
engine with the ignition switch.
When the \briver’s \boor is opene\b with I\bling Stop
System on, I\bling Stop System continues to be
activate\b although the buzzer soun\bs an\b the I\bling
Stop System in\bicator light blinks.
OPERATING IDLING STOP SYSTEM
NOTE:
. The engine stops automatically when the
brake pedal is depressed with the selector
lever in the "D" (Drive) position.
. When the brake pedal is released, the
engine restarts automatically.
. When the Idling Stop System is activated,
the Idling Stop System indicator light illu-
minates in the meter. .
The buzzer sounds and the indicator light
appears in the meter, indicating the condi-
tion of the Idling Stop System. For more
details, see “Stop/Start System indicator
light (if equipped for Europe)/Idling Stop
System indicator light (if equipped for Thai-
land)” (P.2-18) or “Idling Stop System remin-
der buzzer (if equipped for Thailand)” (P.2-
19) .
. The accumulated time of Idling Stop System
and the current saved fuel consumption by
Idling Stop System can be checked using the
drive computer, see “Accumulated time and
current saved fuel consumption (ml (mili-
liter)) by Idling Stop System (if equipped for
Thailand)” (P.2-27) .
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
The Stop/Start System is designed to prevent
unne\fessary fuel \fonsumption, e\bhaust emissions,
and noise during a journey:
.When the vehi\fle \fomes to rest the engine is
automati\fally stopped.
. The engine is then automati\fally restarted before
you are ready to drive away.
CAUTION:
At the end of the journey the engine must be
stopped and ignition switch be turned off. Lock
the vehicle as normal. Turning the ignition OFF
will shut down all electrical systems. Failure to
do this may result in a flat battery.
NORMAL OPERATION
The Stop/Start System stops the engine and will
automati\fally restart the engine. The Stop/Start
indi\fator light is shown in the meter.
The Stop/Start System will automati\fally stop
the engine when all the following \fonditions
are valid.
For MT model
.The shift lever is in Neutral position.
. The \flut\fh pedal is fully released.
. The vehi\fle speed is below about 2 km/h (1
MPH) .
. The driver’s seat belt is fastened.
. The Intelligent Key is in the vehi\fle.
. The driver’s door is \flosed.
For CVT model
. The sele\ftor lever is in the "D" (Drive) or "N"
(Neutral) position. .
The brake pedal is depressed.
. The vehi\fle is stopped.
. The driver’s seat belt is fastened.
. The driver’s door is \flosed.
NOTE:
The following conditions must also be satisfied
before the engine is automatically stopped. If
the engine does not stop this does not indicate a
malfunction in the system:
. The engine coolant temperature is at normal
operating levels.
. The vehicle has driven some distance since
engine start.
. The battery voltage and temperature are
within normal levels.
. The hood is closed.
. The steering wheel is not being turned.
. The system is not in front defogger mode.
(automatic air conditioner)
. The mode dial is not in front defogger mode.
(manual air conditioner)
. The rear window defogger is not operated.
NOTE:
The engine will not restart if the brake pedal is
released while the Stop/Start System is acti-
vated under the following condition:
. The selector lever is in the "P" (Park) position
(for CVT model) .
When the Stop/Start System indi\fator light is
displayed the engine starts running automa-
ti\fally under at least one of the following
\fonditions.
.The \flut\fh pedal is depressed (for MT model) .
. The brake pedal is released with the sele\ftor lever
in the "D"(Drive) or "N"(Neutral) position (for CVT
model) .
. The sele\ftor lever is pla\fed in the "L"(Low) ,
"D"(Drive) or "R"(Reverse) position from the "N"
or "P" position (for CVT model) .
. The driver’s seat belt is unfastened, or the driver’s
door is open (for CVT model) .
. The brake pedal is repeatedly pressed (to maintain
vehi\fle braking performan\fe) .
. The brake pedal is strongly depressed and then
released with the sele\ftor lever in the "P" (Park)
position, resulting in de\freased va\fuum pressure
of the brake booster (for CVT model) .
. The battery voltage be\fomes low (due to ele\ftri\fal
load from other vehi\fle systems like headlights,
heaters, et\f., or au\biliary devi\fes \fonne\fted to the
12 volt so\fket inside the vehi\fle) .
. The vehi\fle speed is above about 2 km/h (1
MPH) .
. The system is in front defogger mode. (automati\f
air \fonditioner)
. The mode dial is in front defogger mode. (manual
air \fonditioner)
. The rear window defogger is operated.
NOTE:
The following conditions will prevent the Stop/
Start System from automatically restarting the
engine. Starting the engine by the ignition
switch is then necessary:
Starting and driving5-21
STOP/START SYSTEM (if equipped
for Europe)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-22Starting and driving
.The driver ’s seat belt is unfastened, or
driver’s door is open (for MT model) .
. The hood is open.
The Stop/Start System is al\fays engaged at the start
o\b a journey (once the engine has been started) . The
engine is automatically stopped and restarted during
the journey i\b conditions are suitable.
STOP/START SYSTEM DISPLAY AND IN-
DICATORS
Engine stop
JVS0071X
When the engine is stopped the in\bormation is
displayed \bor a \be\f seconds.
Vehicle information display: 1. Engine stop guidance
Instrument panel: 2. Stop/Start System indicator light
See “Vehicle in\bormation display” (P.2-20) about the
display. NOTE:
Automatic engine restart is possible whenever
the Stop/Start System indicator light is illumi-
nated in the meter.
CO2 saved
JVS0073X
Whilst the engine remains stopped the vehicle
in\bormation display sho\fs the accumulated quantity
(estimate) o\b carbon dioxide exhaust emissions pre-
vented by the Stop/Start System.
Vehicle information display:
1. CO2 saved in\bormation
Instrument panel: 2. Stop/Start System indicator light
. Push and hold the
button to reset the [CO2
Saved] value.
. The display can be s\fitched bet\feen Stop/Start
System in\bormation and drive computer in\borma-
tion by a short press o\b the
button.
System \bault
JVS0074X
When automatic restart is not possible the in\bormation
is displayed. The engine must be started by turning or
pushing the ignition s\fitch.
The message can be cleared by pressing the
button, restarting the engine, or turning or pushing the
ignition OFF.
Key LOCK \farning
JVS0081XType A
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
JVS0075XType BThe information is \fisplaye\f an\f a \buzzer soun\fe\f to
remin\f the \friver to turn the ignition OFF to avoi\f a flat
\battery
The message can only \be cleare\f \by turning or
pushing the ignition OFF (or restarting the engine) .
PRECAUTIONS ON STOP/START
JVS0076X
The message is \fisplaye\f when there may \be some-
thing wrong with the Stop/Start System. You are
a\fvise\f to have the system checke\f \by a RENAULT
\fealer or qualifie\f workshop.Vehicle information display:
1. System fault warning
Instrument panel: 2. Stop/Start System in\ficator light
The message can \be cleare\f \by pressing the
\button.
NOTE:
The Stop/Start System indicator in the meter
flashes whilst the fault condition remains.
STOP/START SYSTEM OFF SWITCH
JVS0072X
The system can \be temporarily \fisengage\f \by press-
ing the Stop/Start System OFF switch. Pressing the
\button a secon\f time will re-engage the Stop/Start
System.
. When the Stop/Start System is \fisengage\f whilst
the engine is running, the engine is prevente\f from
automatically stopping.
. When the Stop/Start System is \fisengage\f after
the engine has \been automatically stoppe\f \by the
Stop/Start System, the engine will imme\fiately
restart if suita\ble con\fitions are present as
\fescri\be\f un\fer NORMAL OPERATION. The
engine will then \be prevente\f from automatically stopping \furing the same journey.
. Whenever the Stop/Start System is \fisengage\f
the in\ficator light on the Stop/Start System OFF
switch illuminates. In this con\fition the Stop/Start
System cannot prevent unnecessary fuel con-
sumption, exhaust emissions, or noise \furing your
journey.
NOTE:
The following messages may be displayed for a
few seconds in the vehicle information display
when the Stop/Start System OFF switch is
pressed.
More information a\bout the Stop/Start System can \be
checke\f using the [Settings] menu. (See “Vehicle
information \fisplay” (P.2-20) a\bout the \fisplay.)
Starting and driving5-23
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
SSD0891
1. RES/+ switch
2. SET/íswitch
\f. CANCE\b switch
4. Cruise control MAIN switch (For details, see “Cruise control” (P.5-28) .)
5. Speed limiter MAIN switch (When this switch is pushed, the speed limiter
enters the standby mode. If the cruise control
system is on, the system will turn off and the
speed limiter enters the standby mode.)
Speed limiter display and indicators (Type B
model)
JVS0019X
The speed limiter operating condition is shown on the
vehicle information display and instrument panel.
Vehicle information display:1. \bIMIT indicator
2. Set speed indicator
When the vehicle speed exceeds the set speed limit,
the set speed indicator blinks and the accelerator
pedal operation will not work until the vehicle speed
slows down to the set speed limit.
Instrument panel: \f. Speed limiter indicator light
4. SET indicator light
The speed limiter will not automatically brake
the vehicle to the set speed limit.
Speed limiter display and indicators (Type C
model)
JVS0025X
The speed limiter operating condition is shown on the
vehicle information display and instrument panel. Vehicle information display:
1. \bIMIT indicator
2. SET indicator light
\f. Set speed indicator
When the vehicle speed exceeds the set speed limit,
the set speed indicator blinks and the accelerator
pedal operation will not work until the vehicle speed
slows down to the set speed limit.
Instrument panel: 4. Speed limiter indicator light
The speed limiter will not automatically brake
the vehicle to the set speed limit.
Turning on speed limiter
Push the speed limiter MAIN switch. The speed limiter
indicator (light) and the \bIMIT indicators illuminate. The
set speed indicator shows “- - -”.
Setting speed limit
1. Push the SET/í switch..When the vehicle is stopped, the speed will be
set at \f0 km/h or 20 MPH.
.While driving, the speed limit will be set at thecurrent speed.
2. When the speed limit is set, the SET (indicator light) and the set speed indicators illuminate on
the vehicle information display and instrument
panel (for Type B model) .
Changing set speed limit:
Use either of the following operations to change the
speed limit.
. Push and hold the RES/+ or SET/í switch. The
set speed will increase or decrease by approxi-
mately 10 km/h or 10 MPH.
Starting and driving5-27
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-30Starting and driving
Setting cruising speed
1. Acce\ferate to the desired speed.
\b. Push the SETíswitch and re\fease it.
3. The SET indicator \fight and set speed indicator i\f\fuminate on the meter pane\f and the vehic\fe
information disp\fay.
4. Take your foot off the acce\ferator peda\f.
The vehic\fe wi\f\f maintain the set speed.
Passing another vehicle:
Depress the acce\ferator peda\f to acce\ferate. After
re\feasing the acce\ferator peda\f, the vehic\fe wi\f\f return
to the previous\fy set speed.
The vehic\fe may not maintain the set speed when
going up or down steep hi\f\fs. In such cases, drive
without the cruise contro\f.
Resetting to slower speed:
Use any one of the fo\f\fowing methods to reset to a
s\fower speed.
. Light\fy tap the foot brake peda\f. When the vehic\fe
reaches the desired speed, push and re\fease the
SETí switch.
. Push and ho\fd the SETí switch. When the vehic\fe
reaches the desired speed, re\fease the SETí
switch.
. Quick\fy push and re\fease the SETí switch. This
wi\f\f reduce the vehic\fe speed by about 1 km/h or 1
MPH.
Resetting to faster speed:
Use any one of the fo\f\fowing methods to reset to a
faster speed.
. Depress the acce\ferator peda\f. When the vehic\fe
reaches the desired speed, push and re\fease the
SETí switch. .
Push and ho\fd the RES+ switch. When the
vehic\fe reaches the desired speed, re\fease the
RES+ switch.
. Quick\fy push and re\fease the RES+ switch. This
wi\f\f increase the vehic\fe speed by about 1 km/h or
1 MPH.
Resuming at preset speed:
Push and re\fease the RES+ switch.
The vehic\fe wi\f\f resume the \fast set cruising speed
when the vehic\fe speed is over 40 km/h (\b5 MPH) .
Cance\fing cruising speed
Use any one of the fo\f\fowing methods to cance\f the set
speed.
. Push the CANCEL switch. The SET indicator \fight
wi\f\f turn off.
. Tap the foot brake peda\f. The SET indicator \fight
wi\f\f turn off.
. Push the cruise contro\f MAIN switch. Both the
SET and cruise indicator \fights turn off.
WARNING:
.Do not stop or park the vehicle over
flammable materials such as dry grass,
waste paper or rags. They may ignite and
cause a fire.
. Safe parking procedures require that both
the parking brake be applied and the
selector lever placed in the “P ” (Park)
position (Automatic Transmission model/
Continuously Variable Transmission model)
or the shift lever placed in an appropriate
gear (Manual Transmission model) . Failure
to do so could cause the vehicle to move
unexpectedly or roll away and result in an
accident.
. When parking the vehicle, make sure the
selector lever is moved to the “P”(Park)
position. The selector lever cannot be moved
out of the “P ” (Park) position without
depressing the foot brake pedal.
. Never leave the engine running while the
vehicle is unattended.
. When parking for an extended period of time
with Stop/Start (Idling Stop) System (if
equipped) activated, the engine will restart
automatically. Never leave the vehicle with
the ignition switch in the “ON”position.
. Never leave children or adults who would
normally require the support of others alone
in the vehicle. Pets should not be left alone
either. They could unknowingly activate
switches or controls and inadvertently be-
come involved in a serious accident and
injure themselves. On hot, sunny days,
temperatures in a closed vehicle could
PARKING
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
quickly become high enough to cause se-
vere or possibly fatal illness to people and
animals.
SSD0488
Left-Hand Drive (LHD) model
SSD0489
Right-Hand Drive (RHD) model1. Firmly apply the par\fing bra\fe.
\b. Automatic Transmission (AT)/Continuously Vari-able Transmission (CVT) model: Move the selector
lever to the “P” (Par\f) position.
Manual Transmission (MT) model: Move the shift
lever to the “R” (Reverse) position. When par\fing
on an uphill grade, move the shift lever to the “1”
(1st) position. 3. To help prevent the vehicle from moving into traffic
when par\fed on an incline, it is a good practice to
turn the wheels as illustrated.
HEADED DOWNHILL WITH CURB
*1
Turn the wheels into the curb and move the vehicle
forward until the curb side wheel gently touches
the curb. Then apply the par\fing bra\fe. HEADED UPHILL WITH CURB
*2
Turn the wheels away from the curb and allow the
vehicle to move bac\f until the curb side wheel
gently touches the curb. Then apply the par\fing
bra\fe.
HEADED UPHILL OR DOWNHILL, WITHOUT
CURB
*3
Turn the wheels toward the side of the road so the
vehicle will move away from the center of the road
if the vehicle moves. Then apply the par\fing bra\fe.
4. Model with Intelligent Key system:
Place the ignition switch in the “OFF” position.
Model without Intelligent Key system:
Place the ignition switch in the “LOCK” position
and remove the \fey.
NOTE:
For Model with Stop/Start (Idling Stop) System:
Use this system when the vehicle is stopped for
a period of time, for example waiting at stop-
lights.
Stop the engine with the ignition switch when
parking, etc. for an extended period of time.
Starting and driving5-31
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
object with the rate of blinking.
When an object is \fetecte\f, the in\ficator appears an\f
blinks (the tone so\bn\fs intermittently) . When the
vehicle moves closer to the object, the n\bmber of bars
\fecreases an\f the rate of blinking increases (the rate
of the tone increases) . When the corner of the vehicle
is very close to the object, less than 30 cm (11.8 in)
away, the n\bmber of bars \fecreases an\f the in\ficator
stops blinking (the tone so\bn\fs contin\bo\bsly) .
PARKING SPACE MEASUREMENT OP-
ERATION (if eq\bippe\f for E\brope)
System operation
JVS0111XParking space measurement switch*1Parking space meas\brement switch
*2ON in\ficator light
The system is inten\fe\f to help the \friver parallel park
easily. When the system is activate\f by pressing the
switch, it informs the \friver of parallel parking
availability.
Press the switch
*1to t\brn on the parking space
meas\brement system.
JVS0030X
1. Select left or right to parallel park by operating the t\brn signal switch.
2. Drive the vehicle alongsi\fe the cars yo\b will parallel park between at approximately 15 km/h (9
MPH) . Maintain approximately a one meter \fis-
tance between yo\br vehicle an\f the one next to
yo\br vehicle as ill\bstrate\f
*A.
3. When the parking space is meas\bre\f, a beep so\bn\fs.
Starting and driving5-33
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-36Starting and driving
When the electric power steering warning light
ill\fminates with the engine r\fnning, the power assist
for the steering will cease operation\b Yo\f will still have
control of the vehicle\b However, greater steering effort
is needed, especially in sharp t\frns and at low speeds\bThe brake system has two separate hydra\flic circ\fits\b If
one circ\fit malf\fnctions, yo\f will still have braking
ability at two wheels\b
BRAKE PRECAUTIONS
Vac\f\fm assisted brakes
The brake booster aids braking by \fsing engine
vac\f\fm\b If the engine stops, yo\f can stop the vehicle
by depressing the foot brake pedal\b However, greater
foot press\fre on the foot brake pedal will be req\fired
to stop the vehicle\b The stopping distance will be
longer\b
If the engine is not r\fnning or is t\frned off while driving,
the power assisted brakes will not f\fnction\b Braking
will be harder\b
WARNING:
Do not coast with the engine stopped.
When the brake pedal is depressed slowly and firmly,
yo\f may hear a clicking noise and feel a slight
p\flsation\b This is normal and indicates that the Brake
Assist System is operating\b
Using brakes
Avoid resting yo\fr foot on the foot brake pedal while
driving\b This will overheat the brakes, wear o\ft the
brake linings/pads faster, and increase f\fel cons\fmp-
tion\b
To help red\fce brake wear and to prevent the brakes
from overheating, red\fce speed and downshift to a
lower gear before going down a slope or long grade\b
Overheated brakes may red\fce braking performance
and co\fld res\flt in loss of vehicle control\b
While driving on a slippery s\frface, be caref\fl when
braking, accelerating or downshifting\b Abr\fpt brakingor acceleration co\fld ca\fse the wheels to skid and
res\flt in an accident\b
Wet brakes
When the vehicle is washed or driven thro\fgh water,
the brakes may get wet\b As a res\flt, yo\fr braking
distance will be longer and the vehicle may p\fll to one
side d\fring braking\b
To dry the brakes, drive the vehicle at a safe speed
while lightly depressing the foot brake pedal to heat \fp
the brakes\b Do this \fntil the brakes ret\frn to normal\b
Avoid driving the vehicle at high speeds \fntil the
brakes f\fnction correctly\b
Driving \fphill
When starting on a steep grade, it is sometimes
diffic\flt to operate both the brake and cl\ftch (for
Man\fal Transmission model) \b Apply the parking brake
to hold the vehicle\b Do not slip the cl\ftch\b When ready
to start, slowly release the parking brake while
depressing the accelerator pedal and releasing the
cl\ftch pedal\b
Driving downhill
The engine braking action is effective for controlling
the vehicle while descending hills\b For Man\fal Trans-
mission (MT) model, the shift lever sho\fld be placed in
the lower speed position prior to descending\b For
A\ftomatic Transmission (AT) model, the “1” or “2”
position sho\fld be selected\b For Contin\fo\fsly Variable
Transmission (CVT) model, the “L” position sho\fld be
selected\b
BRAKE SYSTEM
&RQGLWLRQ