change time RENAULT SCENIC 2006 J84 / 2.G Multimedia Nav 4R Owner's Manual

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-70
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 5 CD read fault
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Ensure there are no present or stored faults.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Is the fault related to CD reading by the radio/
navigation computer or by the 6CD changer?
By the radio/navigation computer By the 6CD changer
Is the CD an MP3 CD?
Yes
Check that component 261 (commercial vehicle:
662) is compatible with MP3 CDs (see "MP3" logo
on keypad).
Yes
Try with another MP3 CD.
Has the fault disappeared?
Yes
The faulty CD is in poor condition or is not
compatible (only MP3 format is compatible).
No
NoEnd of fault finding.
NoContact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP5

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-77
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 10 The screen displays "CD0000"
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Ensure there are no present or stored faults.
Is this message displayed following replacement
of the radio/navigation computer?
Yes
This message is displayed following replacement of
the radio/navigation computer. Enter the anti-theft
code from the old computer linked to the changer.
The changer registers the new computer's code.
If the old radio code is lost, the changer code can be
cleared using the clearing code.
To obtain the clearing code, contact the Techline.
It is necessary to enter the 6 CD changer
immobiliser code. To do this, follow the instructions
in Technical Note 5037A Code supply procedure.
NoThis message is displayed after the 6 CD
changer is replaced. The computer code
is programmed when the battery or
changer are connected.
When it is installed in the vehicle, the CD
changer is programmed with the radio
supply code.
Note:
The CD changer is supplied uncoded.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP10

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-78
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 11 The 6 CD changer does not work
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Ensure there are no present or stored faults.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Disconnect then reconnect component 1272.
Does the CD changer request its code?
("CD 0000")
No
Check the condition and connection of the connector of components 261 (Trafic: 662) and 1272.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Has the fault been solved?
No
With the radio switched on, check for + battery feed
on connection 34BC and + accessories feed on
connection 34BD of the connector of
component 1272.
Are the + battery and + accessories feeds
present?
Yes
Contact the Techline.
YesRefer to ALP 10 The screen displays
"CD0000".
NoCheck the continuity, insulation and
the absence of interference resistance
on connections 34BC, 34BL and 34BD
between components 261 (Trafic: 662)
and 1272.
Yes Are the connections correct?
No
If the connection or connections are faulty and there is a
repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the
wiring, otherwise replace it.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP11