air condition RENAULT SCENIC 2007 J84 / 2.G Anti Lock Braking System Bosch 8.0 ESP Owner's Manual

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 0A, 0B, 11, 1238C
38C - 35V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 0A, 0B, 11,
12
DF027
CONTINUED 1
Vdiag: 0A, 0B, 11, 12
NO
Check the connection and the condition of the computer connections. Repair if
necessary.
Check the connections (tracks 33 and 34) on the 52-track intermediate black
connection R2 under the front left-hand seat. Repair if necessary.
Check and ensure the continuity of the following connections:
Sensor connector one of the two
tracksTrack 8 computer connector
Sensor connector the other track Track 29 computer connector
Also check the insulation between these two connections. If the connections are faulty,
carry out the following checks:
Check the continuity, insulation and absence of interference resistance between:
Computer connector track 8 Track 34 on the intermediate
connector
Computer connector track 29 Track 33 on the intermediate
connector
Also check the insulation between these two connections.
Check the continuity, insulation and absence of interference resistance between:
Sensor connector one of the
2 tracksTrack 33 on the intermediate
connector
Sensor connector the other track Track 34 on the intermediate
connector
Also check the insulation between these two connections. If all the checks are in order,
contact Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 0A, 0B, 11, 1238C
38C - 36V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 0A, 0B, 11,
12
DF027
CONTINUED 2
Vdiag: 0A, 0B, 11, 12
1.DEF
NOTESNone
Replace the rear right-hand wheel speed sensor.
2.DEF
NOTESNone
Visually inspect the condition of the target and sensor (for dirt, metallic contamination, bearing grease, etc.),
and clean using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the sensor/target air gap through one wheel revolution: 0.1 mm < Rear wheel air gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
If the checks are correct:
–the computer fault memory has been cleared,
–exit fault finding mode, switch off the ignition and carry out a road test.
–replace the rear right-hand "disc-hub-bearing" assembly (see MR 364 or MR 370 Mechanical, 33A,
Rear axle components, Bearing: Removal - Refitting) if the fault reappears.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 37V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF055
PRESENT
VEHICLE PARAMETER PROGRAMMING
1.DEF : absence of vehicle parameter programming
2.DEF : programming invalid
NOTESSpecial notes:
No programming or erroneous value of PR063 "Vehicle parameters". ESP warning
light flashing at 8 Hz outside fault finding conditions.
Read PR063 Vehicle parameters, use command VP004 Vehicle parameters to define the appropriate vehicle
type variant.
It is imperative to select the variant corresponding to the vehicle being tested.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF055P/ESPBOSCH_V09_DF055P/ESPBOSCH_V0A_DF055P/
ESPBOSCH_V0B_DF055P/ESPBOSCH_V11_DF055P/ESPBOSCH_V12_DF055P

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 38V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF063
PRESENT
OR
STOREDWHEEL SPEED CONSISTENCY
CC.1 : short circuit to + 12 V
1.DEF : interference
NOTESSpecial notes:
This fault indicates that the wheel speeds are inconsistent with each other. The
computer does not know how to determine which one is faulty.
Priorities when dealing with a number of faults:
Deal with faults DF006, DF007, DF026 and DF027 first, even when stored.
Conditions for applying the fault finding procedure to stored faults:
The fault appears after a road test at a speed of > 36 mph (60 km/h) on a winding road.
Check the condition of the axle assemblies (impacts, damage, etc.) and the conformity and good condition of the
tyres.
Ensure that the braking system is in good condition (condition of the linings, tightness, grip, bleeding, bearing play,
lubricant on the targets, etc.).
Check that the wheel speed sensor mountings are in good condition.
Check the sensor/target air gap over one wheel revolution: 0.1 mm < wheel air gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
Repair if necessary.
Carry out a visual check on the connection and condition of the sensor and computer connectors Check the
connection and condition of the connections (tracks 31, 32, 33 and 34) on the 52-track intermediate black
connection R2 under the front left-hand seat. Repair if necessary.
If all the checks are correct, clear the computer's fault memory.
Exit the fault finding procedure and carry out a road test. If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF063 /ESPBOSCH_V09_DF063/ESPBOSCH_V0A_DF063/
ESPBOSCH_V0B_DF063 /ESPBOSCH_V11_DF063/ESPBOSCH_V12_DF063

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 39V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF066
PRESENT
OR
STOREDINJECTION MULTIPLEX SIGNAL ABSENT
NOTESSpecial notes:
Although the fault is stored in the computer, it is not caused by ABS/ESP components,
but it indicates that the ESP is deactivated due to an injection frame transmission fault.
Run fault finding on the injection system.
Note:
The injection does not always store these transient faults as quickly as the ABS/ESP
system. If no fault is stored in the injection computer, start the engine; if there is no fault
present, contact the Techline.
Once the fault in the injection system has been repaired, clear the ABS/ESP computer
fault memory.
The injection multiplex signal is transmitted to the ABS/ESP computer via the
Protection and Switching Unit.
Priorities when dealing with a number of faults:
Deal with faults DF152 and DF153 first, whether they are present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started up.
Check the condition and correct locking of the blue PEH connector of the UPC (Vdiag 44) or the grey CT1
connector of the UPC (Vdiag 48 or higher).
Carry out a multiplex network test and check the injection system with the diagnostic tool. If the fault is still
present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF066 /ESPBOSCH_V09_DF066/ESPBOSCH_V0A_DF066/
ESPBOSCH_V0B_DF066 /ESPBOSCH_V11_DF066/ESPBOSCH_V12_DF066

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 40V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF090
STORED
FRONT RIGHT-HAND WHEEL TARGET
NOTESSpecial notes:
This fault means that some magnetic poles of the target are not detected by the sensor.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
Check for play in the bearing.
Visually inspect the condition of the target and sensor (for dirt, metallic contamination, bearing grease, etc.), and
clean using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check the quality of the mounting of the wheel speed sensor (correct clipping without excessive play).
Check the sensor/target air gap over one wheel revolution: 0.1 mm < front wheel air gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
Replace the instrumented bearing if the number of teeth is incorrect.
If all the checks are correct, reconnect the computer and the wheel speed sensor.
Clear the computer fault memory.
Exit fault finding mode, switch off the ignition and carry out a road test.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF090M/ ESPBOSCH_V09_DF090M/ESPBOSCH_V0A_DF090M/
ESPBOSCH_V0B_DF090M/ESPBOSCH_V11_DF090M/ESPBOSCH_V12_DF090M

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 41V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF091
STORED
FRONT LEFT-HAND WHEEL TARGET
NOTESSpecial notes:
This fault means that some magnetic poles of the target are not detected by the sensor.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
Check for play in the bearing.
Visually inspect the condition of the target and sensor (for dirt, metallic contamination, bearing grease, etc.),
and clean using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check the quality of the mounting of the wheel speed sensor (correct clipping without excessive play).
Check the sensor/target air gap over one wheel revolution: 0.1 mm < front wheel air gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
Replace the instrumented bearing if the number of teeth is incorrect.
If all the checks are correct, reconnect the computer and the wheel speed sensor.
Clear the computer fault memory.
Exit fault finding mode, switch off the ignition and carry out a road test.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF091M/ ESPBOSCH_V09_DF091M/ESPBOSCH_V0A_DF091M/
ESPBOSCH_V0B_DF091M/ESPBOSCH_V11_DF091M/ESPBOSCH_V12_DF091M

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 42V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF092
STORED
REAR RIGHT-HAND WHEEL TARGET
NOTESSpecial notes:
This fault means that some of the target teeth are not seen by the sensor.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
Visually inspect the condition of the target and sensor (for dirt, metallic contamination, bearing grease, etc.),
and clean using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the sensor/target air gap through one wheel revolution: 0.1 mm < Rear wheel air gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
Replace the rear right-hand "disc-hub-bearing" assembly (see MR 364 or MR 370 Mechanical, 33A,
Rear axle components, Bearing: Removal - Refitting) if the number of teeth is incorrect.
If all the checks are correct, reconnect the computer and the wheel speed sensor.
Clear the computer fault memory.
Exit fault finding mode, switch off the ignition and carry out a road test.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF092M/ ESPBOSCH_V09_DF092M/ESPBOSCH_V0A_DF092M/
ESPBOSCH_V0B_DF092M/ESPBOSCH_V11_DF092M/ESPBOSCH_V12_DF092M

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 43V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF093
STORED
REAR LEFT-HAND WHEEL TARGET.
NOTESSpecial notes:
This fault means that some of the target teeth are not seen by the sensor.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
Visually inspect the condition of the target and sensor (for dirt, metallic contamination, bearing grease, etc.),
and clean using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the sensor/target air gap through one wheel revolution: 0.1 mm < Rear wheel air gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
Replace the rear left-hand "disc-hub-bearing" assembly (see MR 364 or MR 370 Mechanical, 33A,
Rear axle components, Bearing: Removal - Refitting) if the number of teeth is incorrect.
If all the checks are correct, reconnect the computer and the wheel speed sensor.
Clear the computer fault memory.
Exit fault finding mode, switch off the ignition and carry out a road test.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF093M/ ESPBOSCH_V09_DF093M/ESPBOSCH_V0A_DF093M/
ESPBOSCH_V0B_DF093M/ESPBOSCH_V11_DF093M/ESPBOSCH_V12_DF093M

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 0A, 0B, 11, 1238C
38C - 44V2 MR-372-J84-38C050$434_eng.mif
*USM: NO
BOSCH 8.0 ESP
Vdiag No.: 0A, 0B, 11,
12
DF097
PRESENT
OR
STOREDNO AUTOMATIC TRANSMISSION MULTIPLEX SIGNAL
Vdiag: 0A, 0B, 11, 12
NOTESSpecial notes:
Although it is stored in the computer, this fault does not cause the warning lights to
come on or generate a fault message, because the ABS/ESP system is not faulty. Run
fault finding on the automatic transmission with the diagnostic tool.
Note:
When the fault in the automatic transmission system is repaired, clear the ABS/ESP
fault memory.
The multiplex signal from the automatic transmission is sent to the ABS/ESP via the
Protection and Switching Unit.
Priorities when dealing with a number of faults:
Deal with faults DF152 and DF153 first, whether they are present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started up.
Using the diagnostic tool, check in the parameter screen that the PR063 "Vehicle parameters" truly correspond
with the vehicle undergoing fault finding.
Is PR063 Vehicle Parameters correct?
YES
Check the condition and correct locking of the blue PEH connector on the UPC
(Vdiag 44) or the grey CT1 connector on the USM* (Vdiag 48).
Carry out a multiplex network test.
If the fault is still present, run fault finding on the automatic transmission gearbox and
repair as necessary.
If the fault is still present, contact the Techline.
Use command VP004 Vehicle parameters to define the appropriate parameters for the
vehicle type.
Clear the computer fault memory.
Exit fault finding mode, switch off the ignition and carry out a new test with the diagnostic
tool.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V0A_DF097 / ESPBOSCH_V0B_DF097/
ESPBOSCH_V11_DF097/ESPBOSCH_V12_DF097