stop start RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 User Guide

13B-183
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET077
IMPACT DETECTED
STATUS DEFINITIONNO: This status indicates that the airbag computer has not detected an impact.
YES: This status indicates that the airbag computer has detected an impact.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
This signal is transmitted by the airbag computer via the multiplex network.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
NO
Under normal operating conditions, status ET077 is NO when the computer has
received no impact signal.
YESIf the vehicle has had an accident, the injection computer receives the impact signal via
the multiplex network and may switch off the ignition. Status ET077 is YES.
Switch off the ignition for 1 minute, then switch it on again, so the engine can be
started.
Carry out a multiplex network test and deal with any faults.
Clear the injection computer faults, even if no fault is present.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET077/EDC16_V58_ET077/EDC16_V5C_ET077/EDC16_V18_ET077/EDC16_V1C_ET077/EDC16_V20_ET077

13B-191
MR-372-J84-13B200$504.mif
V13
13B
DIESEL INJECTION
Fault finding – Interpretation of statuses
ET205
ET206
ET207
THERMOPLUNGER NO. 1, 2, 3 RELAY CONTROL
STATUS DEFINITIONACTIVE: This status indicates that the control of thermoplunger relay no. 1, no.2 and
no. 3 is active.
INACTIVE: This status indicates that the control of thermoplunger relay no. 1, no.2 and
no. 3 is not active.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
ACTIVE
Statuses ET205, ET206, ET207 are ACTIVE when:
– the engine has been started,
– and the engine coolant temperature is low (< 15°),
– and the air temperature is low (< 5°).
This program allows the engine coolant to be heated and to enable the passenger
compartment to be heated.
To control the operation of the thermoplunger relays, run the following commands:
– AC063 Heating element no.1 relay.
– AC064 Heating element no.2 relay.
– AC031 “Heating element relay no.3”.
In the event of a fault, refer to the interpretation of faults:
– DF032 “Thermoplunger no. 1 relay control circuit”
– DF033 “Thermoplunger no. 2 relay control circuit”
– DF034 “Thermoplunger no. 3 relay control circuit”.
INACTIVEStatuses ET205, ET206 and ET207 are INACTIVE with the ignition on and the engine
stopped, or when the engine is warm.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_ET205/EDC16_V58_ET205/EDC16_V5C_ET205/EDC16_V18_ET205/EDC16_V1C_ET205/EDC16_V20_ET205/
EDC16_V50_ET206/EDC16_V58_ET206/EDC16_V5C_ET206/EDC16_V18_ET206/EDC16_V1C_ET206/EDC16_V20_ET206/
EDC16_V50_ET207/EDC16_V58_ET207/EDC16_V5C_ET207/EDC16_V18_ET207/EDC16_V1C_ET207/EDC16_V20_ET207 EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C

13B-192
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET238
SYNCHRONISATION
STATUS DEFINITIONCompleted: This status indicates that synchronisation has been carried out.
Not completed: This status indicates that synchronisation is not complete.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
WARNING
Synchronisation is carried out during the engine starting phase. This is established between the camshaft position
sensor and the Top Dead Centre sensor.
Once this synchronisation has been carried out, it enables the computer to identify cylinder no. 1 and to calculate
the precise position of the cylinder's Top Dead Centre.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C
COMPLETED
Synchronisation is carried out during the engine starting phase.
Cylinder no.1 is indicated and the synchronisation will be performed once the engine is
started.
Status ET238 is COMPLETED.
If after several attempts to start the engine, status ET238 remains NOT COMPLETED,
refer to the interpretation of the following faults:
– DF005 Engine speed sensor circuit.
– DF097 Camshaft sensor circuit.
If the engine does not start, consult ALP2 Starting faults (see Fault finding chart).
NOT PERFORMEDWhen the engine is stopped but the ignition switched on, cylinder no. 1 is no longer
indicated.
Status ET238 is NOT PERFORMED: synchronisation between the crankshaft and the
camshaft has not been carried out.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_ET238/EDC16_V58_ET238/EDC16_V5C_ET238/EDC16_V18_ET238/EDC16_V1C_ET238/EDC16_V20_ET238

13B-193
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET341
IMMOBILISER CODE PROGRAMMED
STATUS DEFINITIONYES: This status indicates that the immobiliser code has been programmed.
NO: This status indicates that the immobiliser code has not been programmed.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C
YES
Status ET341 becomes YES if dialogue is established between the UCH and the
injection computer and the card code is recognised.
Engine starting authorisation is only given if the code is recognised by the UCH
computer, and status ET003 Engine immobiliser is INACTIVE.
NOThe code remains NO if dialogue between the UCH and the injection computer is not
possible. Status ET003 Engine immobiliser is ACTIVE.
The cause of the malfunction may be incorrect card programming (see 87B,
Passenger compartment connection unit); in this case, refer to the Technical Note
for the UCH and follow the card programming procedure.
If it is not caused by the card codes, carry out a multiplex network test (if the previous
fault finding check was by function), and check that dialogue is established between the
UCH, the Protection and Switching Unit and the injection computer.
If dialogue is not established, contact the Techline.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_ET341/EDC16_V58_ET341/EDC16_V5C_ET341/EDC16_V18_ET341/EDC16_V1C_ET341/EDC16_V20_ET341

13B-200
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET651
EGR PROGRAMMING CUT-OFF
STATUS DEFINITIONThis status indicates the EGR valve programming cut-off.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80 °C
NONE
No EGR cut-off, the EGR valve is working properly in accordance with the
computer programs.
STATUS 1, 5, 6, 7, 9,
10, 12, 13, 15, 19
23, 24Switch off the ignition and wait 1 minute.
Switch the ignition on and check for faults.
Check the engine battery voltage with the engine switched off and the engine running.
If no faults are present or stored, restart the vehicle and test at idle speed.
Do not accelerate too much and reach an engine speed that is too high.
STATUS 3, 14, 16Accelerate above idle speed for a few seconds.
STATUS 2Check that the clutch pedal (ET405 "Clutch pedal switch") is not pressed and that the
vehicle has stopped completely.
STATUS 4, 17Test the present and stored faults and repair.
STATUS 8Reset the EGR offsets by referring to the interpretation of command SC036
"Reinitialise programming" and select "EGR valve".
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET651/EDC16_V58_ET651/EDC16_V5C_ET651/EDC16_V18_ET651/EDC16_V1C_ET651/EDC16_V20_ET651

13B-208
MR-372-J84-13B200$540.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of statuses
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
ET742
ET743
ET744
ET745
ET746
ET747
ET748
ET749
ET750
ET751STORED REGEN.* REQUEST STATUS NO. 1
STORED REGEN.* REQUEST STATUS NO. 2
STORED REGEN.* REQUEST STATUS NO. 3
STORED REGEN.* REQUEST STATUS NO. 4
STORED REGEN.* REQUEST STATUS NO. 5
STORED REGEN.* REQUEST STATUS NO. 6
STORED REGEN.* REQUEST STATUS NO. 7
STORED REGEN.* REQUEST STATUS NO. 8
STORED REGEN.* REQUEST STATUS NO. 9
STORED REGEN.* REQUEST STATUS NO. 10
STATUS DEFINITIONStatuses ET742 to ET751 correspond to the causes of the regeneration request. They
are associated with parameters PR816 "Stored regeneration start No. 1" to PR825
"Stored regeneration start No. 10" which contain the record of the vehicle mileage at
the start of regeneration (eg. PR745 "Stored regeneration start No. 4" is associated
with "ET709 Stored regeneration request status no. 4").
NOTESSpecial note:
These statuses should only be interpreted for ALP9: Particle filter warning light
comes on too frequently.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80 °C
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET742/EDC16_V58_ET742/EDC16_V5C_ET742/EDC16_V50_ET743/EDC16_V58_ET743/EDC16_V5C_ET743/
EDC16_V50_ET743/EDC16_V58_ET744/EDC16_V5C_ET744/EDC16_V50_ET745/EDC16_V58_ET745/EDC16_V5C_ET745/
EDC16_V50_ET745/EDC16_V58_ET746/EDC16_V5C_ET746/EDC16_V50_ET747/EDC16_V58_ET747/EDC16_V5C_ET747/
EDC16_V50_ET747/EDC16_V58_ET748/EDC16_V5C_ET748/EDC16_V50_ET749/EDC16_V58_ET749/EDC16_V5C_ET749/
EDC16_V50_ET750/EDC16_V58_ET750/EDC16_V5C_ET750/EDC16_V50_ET751/EDC16_V58_ET751/EDC16_V5C_ET751/
EDC16_V18_ET742/EDC16_V1C_ET742/EDC16_V20_ET742/EDC16_V18_ET743/EDC16_V1C_ET743/EDC16_V20_ET743/
EDC16_V18_ET743/EDC16_V1C_ET744/EDC16_V20_ET744/EDC16_V18_ET745/EDC16_V1C_ET745/EDC16_V20_ET745/
EDC16_V18_ET745/EDC16_V1C_ET746/EDC16_V20_ET746/EDC16_V18_ET747/EDC16_V1C_ET747/EDC16_V20_ET747/
EDC16_V18_ET747/EDC16_V1C_ET748/EDC16_V20_ET748/EDC16_V18_ET749/EDC16_V1C_ET749/EDC16_V20_ET749/
EDC16_V18_ET750/EDC16_V1C_ET750/EDC16_V20_ET750/EDC16_V18_ET751/EDC16_V1C_ET751/EDC16_V20_ET751

13B-228
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR038
RAIL PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the rail pressure in bar.
NOTESNo faults should be present or stored.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (starting faults, poor performance, stalling, etc.).
– after interpretation of command AC225 Rail pressure regulator.
Special notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on.
The rail pressure value is between:
0 < PR038 < 10 bar
Default value: 250 bar.
In the event of a fault, consult the interpretation of fault DF007 Rail pressure sensor circuit.
Conformity check with engine running, engine coolant temperature > 80°C.
The rail pressure value is (engine at idle speed):
PR038 = ~ 315 bar
Default value: 250 bar.
In the event of a fault, consult the interpretation of fault DF007 Rail pressure sensor circuit.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR038/EDC16_V58_PR038/EDC16_V5C_PR038/EDC16_V18_PR038/EDC16_V1C_PR038/EDC16_V20_PR038

13B-231
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR041
CONTINUED
Vehicle with ignition on, and the engine stopped for over 1 minute:
Compare the values of PR041 and PR035 Atmospheric pressure.
If the difference between PR041 and PR035 Atmospheric pressure is greater than 0.1 bar,
check the value of PR035 Atmospheric pressure by comparing it with the reading on a vehicle in the workshop
which is correct.
If the value of PR035 Atmospheric pressure is not correct (difference greater than 0.1 bar between
the 2 vehicles), contact the Techline.
Otherwise (when the value PR035 Atmospheric pressure is correct), change the turbocharging pressure
sensor.
If the difference between PR041 and PR035 Atmospheric pressure is less than 0.1 bar.
Start the engine, with the engine idling:
Compare the values of PR041 and PR035 Atmospheric pressure.
If the difference between PR041 and PR035 Atmospheric pressure is greater than 0.2 bar.
Check the air inlet circuit:
absence of leaks or blockages in the low and high pressure air circuit: ducts, presence and tightness of the
mounting clips, mounting of the turbocharger pressure sensor, intercooler, etc.
Check that the damper valve is not jammed closed.
Repair if necessary.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-256
MR-372-J84-13B200$648.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR132
CONTINUED
Sensor electrical conformity.
Test the air inlet circuit (from the air filter inlet to the inlet manifold tracts,
apply test 4 Turbocharged air inlet circuit check):
– air filter unit inlet not blocked and filter not clogged,
–visual inspection only, run test 4 Turbocharged air inlet circuit check for ALP2 Starting difficult or
impossible,
– oil vapour recirculation circuit connected correctly,
–absence of leaks or blockages in the low and high pressure air circuits: ducts, presence and tightness of the
mounting clips, mounting of the turbocharging pressure sensor, intercooler, etc.
– check that the damper valve is not jammed.
Carry out the necessary repairs.
Check the electrical conformity of the air flowmeter:
Check the + 5 V supply to the air flowmeter on connection 3KJ between components 120 and 799.
Check the + 12 V after relay supply to the air flowmeter on connection 3B between components 120 and 799.
Check the continuity and the absence of interference resistance on the following connections:
– connection code 3DV,
– connection code 3DW.
Between components 120 and 799.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Electrical wiring
repair, Wiring: precautions for repairs), repair the wiring; otherwise replace the wiring.
With the flow meter connected, the vehicle ignition on and engine stopped:
Measure the voltage between connections 3DV and 3DW between components 120 and 799.
Replace the air flowmeter if its voltage is not approximately 0.5 V < PR073 Air flowmeter supply voltage < 0.7 V.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-288
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
* rege: regenerationPR816
PR817
PR818
PR819
PR820
PR821
PR822
PR823
PR824
PR825
REGENERATION START RECORD NO. 1
REGENERATION START RECORD NO. 2
REGENERATION START RECORD NO. 3
REGENERATION START RECORD NO. 4
REGENERATION START RECORD NO. 5
REGENERATION START RECORD NO. 6
REGENERATION START RECORD NO. 7
REGENERATION START RECORD NO. 8
REGENERATION START RECORD NO. 9
REGENERATION START RECORD NO. 10
PARAMETER
DEFINITIONThese parameters are shown in Km.
NOTESSpecial notes:
Interpret these parameters only for ALP9 Particle filter warning light comes on too
often.
Conformity check with the engine stopped and the ignition on, or with the engine running and the engine
coolant temperature > 80°C
These parameters are used so that the history of the last ten activations of the particle filter warning light are
known.
For VDIAG 58, 18 and 1C
Each parameter between PR816 and PR825 contains the vehicle mileage when particle filter regeneration starts
when driving. Each parameter is connected with a "Rege* request status record". They are recorded
simultaneously (for example, PR819 is associated with ET745 Rege* request status record no. 4).
Each new recorded value is saved under the next PR (PR+1).
When all ten parameters have a value other than zero, and a new regeneration starts when driving, the mileage
information for PR816 is cleared and replaced with the new value.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR816/EDC16_V58_PR816/EDC16_V5C_PR816/EDC16_V50_PR817/EDC16_V58_PR817/EDC16_V5C_PR817/
EDC16_V50_PR818/EDC16_V58_PR818/EDC16_V5C_PR818/EDC16_V50_PR819/EDC16_V58_PR819/EDC16_V5C_PR819/
EDC16_V50_PR820/EDC16_V58_PR820/EDC16_V5C_PR820/EDC16_V50_PR821/EDC16_V58_PR821/EDC16_V5C_PR821/
EDC16_V50_PR822/EDC16_V58_PR822/EDC16_V5C_PR822/EDC16_V50_PR823/EDC16_V58_PR823/EDC16_V5C_PR823/
EDC16_V50_PR824/EDC16_V58_PR824/EDC16_V5C_PR824/EDC16_V50_PR825/EDC16_V58_PR825/EDC16_V5C_PR825/
EDC16_V18_PR816/EDC16_V1C_PR816/EDC16_V20_PR816/EDC16_V18_PR816/EDC16_V1C_PR817/EDC16_V20_PR817/
EDC16_V18_PR816/EDC16_V1C_PR818/EDC16_V20_PR818/EDC16_V18_PR819/EDC16_V1C_PR819/EDC16_V20_PR819/
EDC16_V18_PR820/EDC16_V1C_PR820/EDC16_V20_PR820/EDC16_V18_PR821/EDC16_V1C_PR821/EDC16_V20_PR821/
EDC16_V18_PR822/EDC16_V1C_PR822/EDC16_V20_PR822/EDC16_V18_PR823/EDC16_V1C_PR823/EDC16_V20_PR823/
EDC16_V18_PR824/EDC16_V1C_PR824/EDC16_V20_PR824/EDC16_V18_PR825/EDC16_V1C_PR825/EDC16_V20_PR825