airbag RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Workshop Manual

13B-13
MR-372-J84-13B200$108.mif
V13
DIESEL INJECTION
Fault finding – System operation
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
Some vehicles have adopted a sensor for detecting water in the diesel fuel, located in the filter. If there is water in
the diesel fuel, the orange "Injection and pre-post heating" warning light will come on.
The system can inject diesel fuel into the engine at a pressure of up to 1600 bar. Before each operation, check that
the injector rail is depressurised and that the fuel temperature is not too high.
You must respect the cleanliness guidelines and safety advice specified in this document for any work on the high
pressure injection system.
Do not remove the internal parts of the pump and injectors. Only the flow actuator, the diesel temperature sensor
and the Venturi tube can be replaced.
For safety reasons, do not loosen high pressure pipe unions when the engine is running.
It is not possible to remove the pressure sensor from the fuel rail because this may cause circuit contamination
faults. If the pressure sensor fails, the pressure sensor, the rail and the five high pressure pipes must be replaced.
Do not remove an injection pump pulley marked with the number 070 575. If the pump needs to be replaced, replace
the pulley.
Supplying any system component directly with +12V is prohibited.
Ultrasonic decoking and cleaning are prohibited.
Never start the engine unless the battery is connected correctly.
Disconnect the injection computer when carrying out any welding work on the vehicle.
b)The connections between the vehicle's various computers are multiplexed.
The electronic system fitted in this vehicle is multiplexed. This system enables dialogue between the various vehicle
computers. As a result:
– the activation of the fault warning lights on the instrument panel is performed by the multiplex network, with the
vehicle speed sensor on the gearbox deactivated,
– vehicle faults are displayed by the multiplex network,
– the vehicle speed sensor on the gearbox is not needed.
The vehicle speed signal on the instrument panel is transmitted by the ABS computer via a wire connection, then
sent out on the multiplex network by the instrument panel. The vehicle speed signal is used mainly by the injection
computer and the airbag computer.WARNING
The engine must not operate with:
– Diesel fuel containing more than 10% diester.
– petrol, even in tiny quantities.

13B-101
MR-372-J84-13B200$324.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of faults
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5C
13B
DF069
PRESENT
OR
STOREDIMPACT DETECTED SIGNAL
1.DEF: Impact stored by the injection computer
NOTESConditions for applying the fault finding procedure to stored faults:
Only apply the interpretation of this fault if the fault is present and the vehicle will not
start.
Special notes:
The fault appears when the injection computer receives a frontal impact signal from
the Airbag computer via the multiplex network.
As soon as the injection computer receives this signal:
– engine operation is prohibited,
– the level 2 warning light is lit.
Use bornier Elé.1681 or Elé.1590 for any operation on the injection computer
connectors.
If the vehicle has been involved in an accident:
Carry out any necessary repairs,
– clear the fault,
– switch off the ignition,
–wait 1 minute,
– switch on the ignition.
If the fault does not reappear, end of fault finding procedure.
If the fault recurs, run fault finding on the AIRBAG computer.
If the vehicle has not been involved in an accident:
Run fault finding on the AIRBAG computer (see 88C, Airbag and pretensioner).
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V50_DF069/EDC16_V58_DF069/EDC16_V5C_DF069/EDC16_V18_DF069/EDC16_V1C_DF069/EDC16_V20_DF069

13B-183
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET077
IMPACT DETECTED
STATUS DEFINITIONNO: This status indicates that the airbag computer has not detected an impact.
YES: This status indicates that the airbag computer has detected an impact.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
This signal is transmitted by the airbag computer via the multiplex network.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
NO
Under normal operating conditions, status ET077 is NO when the computer has
received no impact signal.
YESIf the vehicle has had an accident, the injection computer receives the impact signal via
the multiplex network and may switch off the ignition. Status ET077 is YES.
Switch off the ignition for 1 minute, then switch it on again, so the engine can be
started.
Carry out a multiplex network test and deal with any faults.
Clear the injection computer faults, even if no fault is present.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET077/EDC16_V58_ET077/EDC16_V5C_ET077/EDC16_V18_ET077/EDC16_V1C_ET077/EDC16_V20_ET077

13B-202
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CRUISE CONTROL/SPEED LIMITER BUTTONS
NOTESSpecial notes:
Carry out these checks if the statuses do not correspond with system operation
programming.
INACTIVE
Status ET703 becomes INACTIVE when none of the cruise control/speed limiter
buttons are pressed. These buttons are located on the steering wheel.
To carry out the checks and measurements in complete safety, follow the instructions
for removing the driver's front airbag (see MR 364 (Mégane II), 372 (Scénic II) or 395
(Laguna II), Mechanical, 88C, Airbag and pretensioners, Driver's front airbag,
removal-refitting).
If status ET703 does not display INACTIVE,
– check the condition of the cruise control/speed limiter +/- button and the condition of
its connector.
– check the condition of the cruise control/speed limiter R/0 button and the condition of
its connector.
Repair if necessary.
INCREASEStatus ET703 becomes PLUS when the cruise control/speed limiter + button is pressed.
This button is on the steering wheel, on the left-hand side.
If status ET703 does not display PLUS, check the condition of the cruise control/speed
limiter +/- button, and the condition of its connector. Repair if necessary.
To carry out the checks and measurements in complete safety, follow the instructions
for removing the driver's front airbag (see MR 364 (Mégane II), 372 (Scénic II) or 395
(Laguna II), Mechanical, 88C, Airbag and pretensioners, Driver's front airbag,
removal-refitting).
Measure the resistance of the following connections while pressing the "+" button
(on the button tracks):
– Connection code86G, of component 331.
– Connection code 86M of component 331.
If the resistance is not approximately 300 Ω, check the continuity of the connection
when the button is not pressed.
If there is continuity, replace the +/- control button.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET703/EDC16_V58_ET703/EDC16_V5C_ET703/EDC16_V18_ET703/EDC16_V1C_ET703/EDC16_V20_ET703

13B-203
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CONTINUED 1
DECREASE
Status ET703 becomes "MINUS" when the cruise control/speed limiter "-" button is
pressed. This button is on the steering wheel, on the left-hand side.
If status ET703 does not change to MINUS, check the condition of the cruise control/
speed limiter +/- button, and the condition of its connector. Repair if necessary.
To carry out the checks and measurements in complete safety, follow the instructions
for removing the driver's front airbag (see MR 364 (Mégane II), 370 (Scénic II) or 395
(Laguna II), Mechanical, 88C, Airbag and pretensioners, Driver's front airbag,
removal-refitting).
Measure the resistance of the following connection whilst pressing the "-" button
(on the button tracks):
●Connection code86G, of component 331.
●Connection code 86M of component 331.
If the resistance is not approximately 100 Ω, check the continuity of the connection
when the button is in rest position.
If there is continuity, replace the +/- control button.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Repair precautions), repair the wiring, otherwise replace it.
SUSPENDStatus ET703 becomes SUSPEND when the cruise control/speed limiter 0 button is
pressed. This button is located on the steering wheel, to the right.
If status ET703 does not change to SUSPEND, check the condition of the cruise
control/speed limiter R/0 button, and the condition of its connector.
To carry out the checks and measurements in complete safety, follow the instructions
for removing the driver's front airbag (see MR 364 (Mégane II), 370 (Scénic II) or 395
(Laguna II), Mechanical, 88C, Airbag and pretensioners, Driver's front airbag,
removal-refitting).
Measure the resistance of the following connection whilst pressing the 0 button
(on the button tracks):
●Connection code86G, of component 331.
●Connection code 86M of component 331.
If the resistance is not approximately 0Ω, replace the R/0 control button.
If there is continuity, replace the R/0 control button.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Repair precautions), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-204
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CONTINUED 2
RESUME
Status ET703 becomes RESUME when the cruise control/speed limiter R button is
pressed. This button is located on the steering wheel, to the right.
If status ET703 does not change to RESUME, check the condition of the cruise control/
speed limiter R/0 button, and the condition of its connector. Repair if necessary.
To carry out the checks and measurements in complete safety, follow the instructions
for removing the driver's front airbag (see MR 364 (Mégane II), 370 (Scénic II) or 395
(Laguna II), Mechanical, 88C, Airbag and pretensioners, Driver's front airbag,
removal-refitting).
Measure the resistance of the following connection whilst pressing the R button
(on the button tracks):
●Connection code86G, of component 331.
●Connection code 86M of component 331.
If the resistance is not approximately 900 Ω, check the continuity of the connection
when the button is in rest position.
If there is continuity, replace the R/0 control button.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Repair precautions), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-318
MR-372-J84-13B200$828.mif
V13
13B
DIESEL INJECTION
Fault finding – Fault Finding Chart
ALP 1 No dialogue with engine management computer
Try to establish dialogue with a computer on another vehicle to check that the diagnostic tool is not faulty.
Check the battery voltage and carry out the operations necessary to obtain the correct voltage
(9.5V<X<17.5V).
If the tool is not at fault, and dialogue cannot be established with any other computer on the same vehicle, the
cause could be a faulty computer interfering on the multiplex network.
disconnect the engine management computer.
try to establish dialogue with another computer.
if the fault is still present, reconnect the computer and proceed by elimination by successively disconnecting all
the following computers (according to wiring diagram and equipment): air conditioning, airbag, abs and esp, uch,
instrument panel, central communication unit, proximity sensor.
try to establish a dialogue between each disconnection:
if, after a disconnection, you manage to establish dialogue, perform the fault finding procedure for the relevant
computer.
Carry out a fault finding procedure on the multiplex network using the diagnostic tool.
Check for the injection fuses on the protection and switching unit and/or in the engine fuse box and check their
condition.
Check the connection of the computer connectors and the condition of its connections.
Check the injection computer earths (quality, oxidation, tightness of earth bolts on the battery terminal).
Check that the supply to the computer is correct:
Earth on connections NT (Laguna II) or N (Scénic II and Mégane II) of component 120.
+ after ignition feed on connection AP29 (Laguna II) or AP15 (Scénic II and Mégane II) of component 120.
Check that the power supply to the diagnostic socket is correct:
– + before ignition feed on connection BP32 (Scénic II and Mégane II) or BCP4 (Laguna II) of component
225.
– + after ignition feed on connection AP43 (Scénic II and Mégane II) or AP10 (Laguna II) of component
225.
– Earth on connections MAN and NAM (Scénic II and Mégane II) or MA and NAP (Laguna II) of component
225.
If dialogue has still not been established after these checks, contact the techline.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16_V50_ALP1/EDC16_V58_ALP1/EDC16_V5C_ALP1/EDC16_V18_ALP1/EDC16_V1C_ALP1/EDC16_V20_ALP1 EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5C
MR-372-J84-13B200$828.mif