RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Workshop Manual

13B-201
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
*ADAC: Trip Computer
DF1020
PRESENT
OR
STOREDENGINE OIL DILUTION
1. DEF: Above maximum threshold
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– the engine is started.
– a road test.
Special notes:
If the fault is present:
– particle filter regeneration is inhibited.
Use bornier Elé. 1681 for any operations on the injection computer connectors.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
Note:
This fault is activated in case of considerable oil dilution due to a significant number of particle filter regenerations.
Carry out the following:
– An oil change (see MR 364 (Mégane II) or MR 370 (Scénic II), Mechanical, 10A Engine and peripherals,
Engine oil: Draining – Filling),
– reset the oil wear meter,
– clear the faults.
Reset the oil wear meter after the oil change:
It will be necessary to reinitialise the display of the trip computer.
With the ignition on:
– hold down the TC* button for 5 s.
Re-initialisation has worked when the on-board computer no longer displays the key.
If this is not the case, restart the procedure.
Specific case:
If an oil change is performed before the oil service interval warning is exceeded, reinitialise the display.
EDC16C36_V50_DF1020/EDC16C36_V58_DF1020EDC16 C36
Program No.: 91
Vdiag No.: 50, 58

13B-202V9 MR-372-J84-13B450$110.mif
13B
The global conformity check for the functions and sub-functions of this system is no longer interpreted in the
conformity check. Instead, all information available in the functions and sub-functions can be found in the following
chapters:
For STATUSES, refer to the "INTERPRETATION OF STATUSES" section.
For PARAMETERS, refer to the "INTERPRETATION OF PARAMETERS" section.
For COMMANDS, refer to the "INTERPRETATION OF COMMANDS" section.
EDC16C36_V44_CCONF/EDC16C36_V4C_CCONF/EDC16C36_V48_CCONF/EDC16C36_V50_CCONF/EDC16C36_V54_CCONF/
EDC16C36_V58_CCONF
DIESEL INJECTION
Fault finding – Conformity check
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-203V9 MR-372-J84-13B450$120.mif
13B
Tool status Diagnostic tool title
ET001+ After ignition computer feed
ET003Engine immobiliser
ET004Air conditioning authorisation
ET007Pre-postheating control
ET014Fan assembly 1 check
ET015Monitor cooling fan 2
ET038Engine
ET039Brake pedal
ET040Clutch pedal
ET042Cruise control/speed limiter
ET076Starting
ET077Impact detected
ET079Air conditioning present
ET104Injector code use
ET120Pre-postheating signal
ET143Low speed fan assembly relay control
ET144High-speed fan assembly relay control
ET205Heating element No. 1 relay control
ET206Heating element No. 2 relay control
ET207heating element No. 3 relay control
ET238Synchronisation
ET300Richness regulation
ET341Immobiliser code programmed
ET405Clutch pedal switch
ET415Deactivation of cruise control/speed limiter
ET651EGR programming cut-off
ET703Cruise control/speed limiter buttons
ET704Brakecontact No. 1
ET705Brakecontact No. 2
DIESEL INJECTION
Fault finding – Status summary table
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-204V9 MR-372-J84-13B450$120.mif
DIESEL INJECTION
Fault finding – Status summary table13B
Tool status Diagnostic tool title
ET706Stored engine status No. 1
ET707Stored engine status No. 2
ET708Stored engine status No. 3
ET709Stored engine status No. 4
ET710Stored engine status No. 5
ET711Stored engine status No. 6
ET712Stored engine status No. 7
ET713Stored engine status No. 8
ET714Stored engine status No. 9
ET715Stored engine status No. 10
ET742Stored regeneration request status No. 1
ET743Stored regeneration request status No. 2
ET744Stored regeneration request status No. 3
ET745Stored regeneration request status No. 4
ET746Stored regeneration request status No. 5
ET747Stored regeneration request status No. 6
ET748Stored regeneration request status No. 7
ET749Stored regeneration request status No. 8
ET750Stored regeneration request status No. 9
ET751Stored regeneration request status No. 10
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-205V9 MR-372-J84-13B450$131.mif
13B
ET001COMPUTER + AFTER IGNITION FEED
STATUS DEFINITIONPRESENT: This status indicates that the + after ignition feed is active.
"ABSENT": This status indicates that the + after ignition is not active.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Use the Mégane II ph2, Scénic II ph2 Wiring Diagram Technical Note.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
PRESENTIgnition on and engine running warm at idle speed with the + after ignition feed
activated.
In the event of a fault, apply the interpretation of DF046 Battery voltage or DF151
Main relay circuit.
EDC16C36_V44_ET001/EDC16C36_V4C_ET001/EDC16C36_V48_ET001/EDC16C36_V50_ET001/EDC16C36_V54_ET001/
EDC16C36_V58_ET001
DIESEL INJECTION
Fault finding – Interpretation of statuses
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-206V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET001
CONTINUED
Sensor electrical conformity
ABSENT
NOTESIgnition on
If the ignition is not switched on, the status ET001 must be ABSENT.
As soon as the ignition is switched on, the computer should be supplied with power. The status ET001 becomes
PRESENT.
If this status remains locked on ABSENT, follow the procedure below:
Check the status of fuse FM3 (30A) in the engine fuse and relay box.
Check the continuity and absence of any interference resistance on the following connection:
– connection code 3AA between components 120 and 983.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
If the fault is still present, contact the Techline.
PRESENT
NOTESIgnition on
Normal operating condition.
The computer is correctly supplied after the ignition has been switched on.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-207V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET003ENGINE IMMOBILISER
STATUS DEFINITIONACTIVE: This status indicates that the immobiliser is active.
INACTIVE: This status indicates that the immobiliser is not active.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
ACTIVERefer to the fault finding note for the UCH (see 87B, Passenger compartment
connection unit).
INACTIVERefer to the fault finding note for the UCH (see 87B, Passenger compartment
connection unit).
EDC16C36_V44_ET003/EDC16C36_V4C_ET003/EDC16C36_V48_ET003/EDC16C36_V50_ET003/EDC16C36_V54_ET003/
EDC16C36_V58_ET003
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-208V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET004AIR CONDITIONING AUTHORISATION
STATUS DEFINITIONYES: This status indicates that the air conditioning is active.
NO: This status indicates that the air conditioning is inactive.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
YES
or
NOIf the air conditioning is authorised or the compressor actuated (see 62A, Air
conditioning).
EDC16C36_V44_ET004/EDC16C36_V4C_ET004/EDC16C36_V48_ET004/EDC16C36_V50_ET004/EDC16C36_V54_ET004/
EDC16C36_V58_ET004
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-209V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET004
CONTINUED
Sensor electrical conformity
YESThe air conditioning authorisation only changes to YES if:
– the air conditioning request has been made by the driver (air conditioning switch in
AC or AUTO position with minimum ventilation),
– the engine is not under full load,
– the air conditioning system is not faulty.
NOStatus ET004 remains NO under the following conditions:
– Vehicle stopped with the ignition on,
– faults present in the air conditioning circuit,
– no air conditioning request made by the driver,
– engine under full load.
If status ET004 remains NO then the air conditioning should be authorised. Check:
– that the air conditioning compressor starts correctly,
– the air conditioning system supply fuses,
– the presence of refrigerant in the air conditioning circuit,
If the fault is still present, check the air conditioning computer faults (see 62B, Air
conditioning).
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-210V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET007PRE-POSTHEATING UNIT CONTROL
STATUS DEFINITIONACTIVE: when the heater plugs are activated according to the temperature of the
engine coolant.
INACTIVE: after the engine has been running for a certain period.
In the event of a fault, consult the interpretation of fault DF017 Preheating unit control
circuit.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Use the Mégane II ph2, Scénic II ph2 Technical Note wiring diagram.
Conformity check with engine stopped and ignition on
ACTIVEWhen the ignition is switched on, the status ET007 must have an ACTIVE status for a
time that varies depending on the temperature of the engine coolant. Both the relay
and the heater plugs are supplied.
After starting, the status should remain ACTIVE for a time that varies depending on
the engine temperature. This is the postheating phase.
If ET007 is INACTIVE when the ignition is switched on, check:
– The supply fuse FM12 (70A) in (597) the engine fuse and relay box.
– The feed to the heater plugs after relay actuation, and the connections of the heater
plugs.
IMPORTANT
On this engine, the plug supply voltage is variable.
EDC16C36_V44_ET007/EDC16C36_V4C_ET007/EDC16C36_V48_ET007/EDC16C36_V50_ET007/EDC16C36_V54_ET007/
EDC16C36_V58_ET007
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58