catalytic converter RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Workshop Manual

13B-10V9 MR-372-J84-13B450$030.mif
13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
High pressure pump:
The high pressure pump is located upstream of the common rail.
Rail pressure sensor:
This sensor is fitted to the common rail.
Rail pressure regulator:
The regulator is fitted on the high pressure pump.
Four injectors:
The injectors are fitted on the cylinder head after the common rail.
Vacuum pump:
The vacuum pump is fitted at the end of the camshaft.
Control solenoid valve:
This solenoid valve is located on the turbocharger.
Turbocharger:
The turbocharger is located after the exhaust manifold.
Turbocharger pressure sensor:
The turbocharger pressure sensor is fitted to the air circuit between the turbocharger and the damper valve.
Air mass flow meter:
The air mass flow meter is located at the air circuit inlet and integrates the air temperature sensor.
EGR valve:
The EGR valve is located between the inlet manifold and the exhaust manifold.
EGR position sensor:
This sensor is integrated into the EGR valve.
Damper valve:
The damper valve is located before the inlet manifold.
Particle filter:
The filter is located on the exhaust line after the catalytic converter (only on engines F9Q816).
TDC sensor:
This sensor is located on the flywheel.
Camshaft sensor:
This sensor is located at the end of the camshaft.
DIESEL INJECTION
Fault finding – List and location of components

13B-11V9 MR-372-J84-13B450$030.mif
DIESEL INJECTION
Fault finding – List and location of components13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Refrigerant pressure sensor:
This sensor is located on the coolant circuit.
Engine coolant temperature sensor:
This sensor is located on the cylinder head near the engine water chamber.
Air temperature sensor:
The air temperature sensor is located at the air circuit inlet, integrated into the air flowmeter.
Turbocharging pressure sensor solenoid valve:
This solenoid valve is located on the turbocharger.
Catalytic converter:
The catalytic converter is located downstream of the turbocharger.
Fuel temperature sensor:
This sensor is located near the injection pump and injector return.
Cruise control/speed limiter on/off switch:
This switch is located in the passenger compartment to the left of the steering wheel near the lighting dimmer.
Fan unit relay:
The relay is located on the cooling radiator.
Accelerator potentiometer:
The potentiometer is located on the accelerator pedal.
Clutch pedal switch:
The switch is located on the clutch pedal.
Heater plugs:
The heater plugs are located on the cylinder head.
The richness ratio sensor:
The richness ratio sensor is mounted in the turbo outlet.
The turbocharger cooling pump:
This pump is located next to the turbocharger.
Particle filter downstream temperature sensor:
The sensor is located after the particle filter (only on certain F9Q816 engines in Vdiag 48).
Particle filter upstream temperature sensor:
The sensor is located before the particle filter (only on engine type F9Q816).
Particle filter differential pressure sensor:
The sensor is located on the particle filter (only on engine type F9Q816).

13B-13V9 MR-372-J84-13B450$040.mif
DIESEL INJECTION
Fault finding – Role of components13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Particle filter:
The particle filter retains the particles for destruction during regeneration, preventing these particles from being
discharged into the atmosphere (engine type F9Q816 only).
TDC sensor:
The angular position is measured using a magneto-inductive sensor triggered by the machined teeth on the engine
flywheel. This sensor gives the engine speed as well as the position of the crankshaft for injection.
Camshaft sensor:
This sensor provides a signal to perform the injection cycle.
When the piston for cylinder 1 is at top dead centre (TDC), it may be either at the end of the compression stroke or
at the end of the exhaust stroke. The camshaft sensor makes the distinction between these two states.
Electric coolant pump:
The electric water pump is activated if the coolant temperature has reached a significant temperature threshold
when the engine has stopped.
Role: to cool the turbocharger when the engine is stopped.
Refrigerant pressure sensor:
Its role is to measure the refrigerant pressure in the air conditioning circuit.
Heating elements:
The heating elements heat the engine coolant to improve user comfort (only on certain types of F9Q816 engine
in Vdiag 48).
Engine coolant temperature sensor:
The engine coolant temperature sensor informs the computer of the engine coolant temperature.
Air temperature sensor:
The air temperature sensor is fitted inside the inlet manifold and informs the computer of the temperature of the air
taken in by the engine.
Turbocharging pressure sensor solenoid valve:
This solenoid valve operates the turbocharger wastegate pneumatic circuit to lower the turbocharging pressure.
Catalytic converter:
The role of the catalytic converter is to convert pollutant gases into harmless gases.
Fan unit relay:
This relay controls the activation of the engine cooling fan assembly when a temperature threshold has been
exceeded.
Accelerator potentiometer:
The accelerator potentiometer informs the computer of the position of the accelerator pedal (engine load).

13B-21V9 MR-372-J84-13B450$050.mif
DIESEL INJECTION
Fault finding – Features13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Catalysed particle filter management (for F9Q816 engine only):
The particle filter prevents the escape of carbon particles emitted by the engine but not yet removed from the
exhaust gases.
The particle filter is a microporous structure containing channels arranged so as to force-filter the exhaust gases.
The exhaust pipe consists of several components:
– an oxidation catalytic converter mounted after the turbocharger. This catalytic converter ensures that HC/CO levels
meet current standards by generating the heat (rise in exhaust temperature caused by catalysis) required for
particle filter regeneration.
– a particle filter located under the body,
– a differential pressure sensor to inform the computer of the pressure difference upstream and downstream of the
particle filter
– a particle filter upstream temperature sensor,
– a particle filter downstream temperature sensor (only on certain F9Q816 engines in VDiag 48),
– a temperature sensor upstream of the turbine (TAVT).
During driving, the particle filter becomes loaded with particles of soot. When a given weight of soot determined by
computer mapping is reached, regeneration mode can be triggered if the maximum weight of soot in the particle filter
has not been reached and the engine operating conditions are met (coolant temperature, etc.)
Particle filter regeneration consists of burning the particles of soot that have accumulated in the filter.
The differential pressure sensor measures the particle filter inlet/outlet pressure differential; this measurement is
used to estimate the weight of soot present in the particle filter by mapping in the computer:
(soot weight = pressure differential as a function of exhaust volume flow rate).

13B-405V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST1 Exhaust system check:
Engine stopped: Check that the silencer outlet is not blocked.
Repair or replace the silencer, if necessary.
Check the seal of the exhaust manifold on the contact surface
between the turbocharger and the exhaust manifold.
Is the seal in order?Repair or replace the faulty part.
Loosen the catalytic converter on the turbocharger side.
Place a wooden block between the two parts.
Start the vehicle and check if the engine runs better.
Is the engine running normally?The exhaust pipe is not the cause of
the fault, repeat the engine fault
finding (see Customer complaints -
Fault finding chart (ALP)).
Retighten the catalytic converter.
Loosen or disconnect the intermediate chamber on the catalytic
converter side. Place a wooden block between the two parts if
necessary.
Start the vehicle and check if the engine runs better.
Is the engine running normally?Replace the catalytic converter.
Retighten the intermediate chamber.
Loosen or disconnect the silencer on the intermediate chamber
side. Place a wooden block between the two parts, if
necessary.
Start the vehicle and check if the engine runs better.
Is the engine running normally?Replace the intermediate chamber.
Replace the silencer.
YES
NO
YES
NO
YES
NO
YES
NO
YES
EDC16C36_V44_TEST1/EDC16C36_V4C_TEST1/EDC16C36_V48_TEST1/EDC16C36_V50_TEST1/EDC16C36_V54_TEST1/
EDC16C36_V58_TEST1
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58