abs RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Owner's Guide

13B-73
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF112
STOREDCYLINDER REFERENCE SENSOR CIRCUIT1.DEF: No signal
2.DEF: Inconsistency
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present with the engine under the starter or when idling.
Check the connection and condition of the 3-track connector of the cylinder reference sensor.
Repair if necessary.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track 2 Track E2 computer connector B
Sensor connector track 1Track E3 computer connector B
If necessary replace the sensor.
Check the timing setting using the appropriate Workshop Repair Manual.
DDCR_V44_DF112M/DDCR_V48_DF112M

13B-74
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF113
PRESENTSENSOR SUPPLY VOLTAGE1.DEF: At minimum limit
2.DEF: At maximum limit
NOTESSpecial notes:
If DF113, the engine stops immediately and cannot be restarted. The level 1 warning
light illuminates along with the message Faulty injection.
Check the condition and connection of the connectors of all sensors with a 5 V feed.
– Refrigerant pressure sensor
– Pressure sensor and inlet manifold temperature sensor
– Rail pressure sensor
– Pedal sensor gang 1
– EGR valve position sensor
– Flow sensor.
Repair if necessary.
Check the condition and connection of computer connectors A, B, and C.
Repair if necessary.
To locate any internal fault in one of the sensors with a 5 V supply (short circuit), disconnect each of the sensors
on the list above in turn, checking after each disconnection whether the fault changes status from present to
stored.
If the faulty sensor is located, check its connections and that it is in order. If necessary replace the sensor.
Connect the bornier in place of the computer and check the insulation, continuity and the absence of
interference resistance on the following connections:
Computer connector C track C4 Track B refrigerant pressure sensor
Computer connector B track C1 Track 3 inlet pressure - temperature sensor
Computer connector B track D1 Track 3 rail pressure sensor
Computer connector A track G2 Track 3 pedal sensor gang 1
Computer connector B track B1 Track 2 EGR valve position sensor
Computer connector B track A1 Track 3 of the flowmeter
Repair if necessary.
If the fault is still present, apply the fault finding procedure for each sensor with a 5 V supply.
DDCR_V44_DF113P/DDCR_V48_DF113P

13B-78
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF121
STOREDACCELEROMETER CIRCUIT
NOTESPriorities when dealing with a number of faults :
DF001 Coolant temperature sensor circuit,
DF002 Air temperature sensor circuit,
DF098 Fuel temperature sensor circuit,
DF003 Atmospheric pressure sensor circuit.
A fault on these sensors could lead to incorrect fault finding on the accelerometer.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Check the conformity of the injectors fitted to the vehicle in relation to the type of vehicle and engine number
(low, high or very high pressure injector).
Check the condition and connection of the accelerometer connector.
Repair if necessary.
Check the connection and condition of the brown 48-track connector B of the computer and check the sensor
shielding on track K1.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track 1 Track F1 computer connector B
Sensor connector track 2 Track G1 computer connector B
Repair if necessary.
Check that the C2I is correctly entered on the computer.
Check that the accelerometer is secured on the engine.
Disconnect and reconnect the accelerometer sensor to accomplish fast programming.
Carry out a road test followed by another check with the diagnostic tool.
If the fault is still present, replace the accelerometer.

13B-80
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF122
CONTINUED
C0.1NOTESNone.
Check the connection and condition of the pedal potentiometer connector.
Repair if necessary.
Check the connection and condition of the black 32-track connector A of the computer.
Repair if necessary.
Measure the resistance between tracks 2 and 6 of the pedal potentiometer.
Replace the pedal potentiometer if the resistance is not 2.85 kΩ +
2.05 Ω.
Disconnect computer connector A and the pedal potentiometer connector.
– Check the insulation on connector A between tracks F2 and F4.
– Check the insulation against +12 V of the connection on track F2 on computer connector A.
Repair if necessary.
Check the continuity, insulation, and the absence of interference resistance on the following connections:
Sensor connector track 1 Track F1 computer connector B
Sensor connector track 2 Track G1 computer connector B
Repair if necessary.

13B-81
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF130
STOREDFLOW CAPACITY FUNCTION
NOTESSpecial notes:
If DF130, the engine may stop with the level 1 and 2 warning lights illuminated along
with the message Faulty injection.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
Check the connection and condition of the of the fuel flow actuator connector (IMV), and repair it if necessary.
Measure the resistance between tracks 1 and 2 of the flow actuator.
Replace the flow actuator if the resistance is not 5.3 Ω ± 0.5 Ω at 20°C.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connection:
Computer connector B track M4 track 1 fuel flow actuator
Repair if necessary.
Check that there is fuel present in the tank and that it is correct. Run Test 13 Diesel fuel conformity check.
Run Test 1 Low pressure circuit check.
Run Test 6 High pressure system check.
Repair if necessary.
DDCR_V44_DF130M/DDCR_V48_DF130M

13B-86V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
MAIN COMPUTER STATUSES AND PARAMETERS: (continued 3)
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Vehicle speedPR089: Vehicle
speedIndicates the vehicle speed in
mph. This parameter is
transmitted by the ABS
computer or by the vehicle
speed ECU. This signal is
transmitted to the injection
system on the multiplex
network. Test the multiplex network.
Refer to fault finding for the
ABS or the vehicle speed
ECU.
New pump
chamber filling ET637: New pump
chamber fillingCOMPLETEDIf NOT DONE, see
Replacement of components.

13B-87V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
STARTING SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
+ After ignition
computer feedET001: + After ignition
computer feed.
PRESENTIndicates + after ignition feed to
the computer.
- Present
- AbsentIn the event of a fault, apply
the fault finding procedure for
DF047 "Computer feed
voltage" or DF015 "Main relay
control circuit".
StartingET076: Starting.
AUTHORISEDIndicates whether or not
starting has been authorised by
the injection.
AUTHORISED: The injection
authorises starting.
PROHIBITED: The injection
does not authorise starting.If PROHIBITED, carry out
a complete fault finding
procedure on the preheating
system.
EngineET038: Engine.
UNDER + AFTER
IGNITION FEEDIndicates the current status of
the engine.
- UNDER + AFTER IGNITION
FEED
- UNDER STARTER
- RUNNING
- SUPPLY MAINTAINED: Supply
maintained during the power
latch phase.
- STALLED: When the engine
has stalled.
- PROTECTED: When a fault has
appeared or when the engine
speed is locked at a certain
value.NONE
Battery
voltagePR074: Battery
voltage.12 V < PR074 < 13.5 VIf there is a fault, apply the
fault finding procedure for
the "Charge circuit".

13B-90V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
COLD LOOP SUB-FUNCTION (continued 1):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Air conditioning
authorisedET004: Air
conditioning
authorised.
NONon operational information,
designed solely for fault finding
purposes.
- YES: Satisfactory engine
operating conditions (coolant
temperature, engine load etc.).
The vehicle is not in a specific
movement phase (hill start, start
from stop etc.).
- NO: One of the above
conditions is not fulfilled.NONE
Refrigerant
pressure.PR037: Refrigerant
pressure.Gives the value in BAR for the
refrigerant fluid in the system.
2 bar < PR037 < 27 bar
Default value: 0 barIf there is a fault apply the fault
finding procedure for DF049
"Refrigerant sensor circuit". If
the fault is still present, replace
the refrigerant sensor.
Engine speedPR055: Engine
speed.Indicates the engine's speed of
rotation in rpm.In the event of a fault, apply the
fault finding procedure for
DF005 "Engine speed sensor
circuit".
Fast idle speed
requestET023: Fast idle
speed request.
ABSENTThe UCH requests fast idle speed
from the injection.
- ABSENT: The UCH did not make
a request.
- PRESENT: The UCH made
a request.If ET023 is inconsistent, carry
out a multiplex network test
using the diagnostic tool. If the
test is correct, consult the fault
finding procedure for the UCH.
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90°CIndicates the coolant
temperature in °C.
Default value: 80°CIn the event of a fault, consult
the interpretation of parameter
PR064 Coolant temperature.

13B-91V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
COLD LOOP SUB-FUNCTION (continued 2):
* When the air conditioning is requested with the engine idling and the vehicle speed = 0 mph (0 km/h),
ET022 will always be ACTIVE and ET021 INACTIVE (unless refrigerant pressure > 15 bar, vehicle speed
= 0 mph, and high coolant temperature). The fan assemblies are disabled under certain coolant temperature
conditions when driving.
When the UPC stops receiving multiplex transmissions from the injection, the fan assemblies are
constantly activated.
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Vehicle speedPR089: Vehicle
speed.Indicates the vehicle speed in mph.
This parameter is transmitted by the
ABS computer or by the vehicle
speed ECU. This signal is
transmitted to the injection system
on the multiplex network.Test the multiplex network.
Refer to fault finding for the
ABS or the vehicle speed
ECU.
Power consumed
by the air
conditioning
compressorPR125: Power
consumed by the air
conditioning
compressor.
0 WIndicates the power consumed by
the compressor.NONE
Speed request
for fan
assembly*ET022: Low speed
fan assembly
request.
INACTIVE.The injection requests the UPC to
start the fans.
- INACTIVE: Because engine speed
= 0 rpm.
- ACTIVE: Engine speed = idle
speed, correct refrigerant pressure
and vehicle speed = 0 mph (km/h),
or high coolant temperature.NONE
Speed request
for fan
assembly*ET021: High speed
fan assembly
request.
INACTIVE.The injection requests the UPC to
start the fans.
- INACTIVE: Because engine speed
= 0 rpm.
- ACTIVE: Engine speed = idle
speed. Refrigerant pressure
> 15 bar, vehicle speed = 0 mph,
or high coolant temperature.NONE

13B-102V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
CRUISE CONTROL - SPEED LIMITER SUB-FUNCTION (continued 1):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or
Status Check
or actionDisplay and notes Fault finding
Brake contactET704: Brake
switch No. 1- INACTIVE
- ACTIVE (brake pedal depressed)Consult the
interpretation of status
ET704 Brake switch
No. 1
ET705: Brake
switch No. 2- ACTIVE (brake pedal released)
- INACTIVEConsult the
interpretation of status
ET705 Brake switch
No. 2
Clutch pedal
switchET405: Clutch
pedal switch- ACTIVE
- INACTIVEConsult the
interpretation of status
ET405 Clutch switch
Cruise control
setpointPR130: Cruise
control setpointIndicates the reference value requested by
the driver (in mph (km/h))NONE
Vehicle speedPR089: Vehicle
speed0 mph (km/h)
Gives the vehicle speed in mph (km/h). This
parameter is transmitted by the ABS computer or
vehicle speed ECU*. This signal is transmitted to
the injection on the multiplex network.Test the multiplex
network. See fault
finding for the ABS
system or the
vehicle speed ECU*.