abs RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Service Manual

13B-106V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
MAIN COMPUTER STATUSES AND PARAMETERS (continued 2):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Engine
immobiliserET003: Engine
immobiliser.
INACTIVEIndicates the status of the
immobiliser system.
- INACTIVE: The injection
computer has recognised the
immobiliser code transmitted by
the UCH.
- ACTIVE: The injection computer
has not recognised the
immobiliser code transmitted by
the UCH.If ACTIVE, apply
the associated Help given in
the tool.
Code
programmedET006: Code
programmed
YESIndicates whether the
immobiliser code has been
programmed into the computer.
- YES: Code is programmed.
- NO: Code was not programmed
into the injection computer.If NO, contact the Techline.
Vehicle speed PR089: Vehicle speedIndicates the vehicle speed in
mph. This parameter is
transmitted by the ABS
computer or by the vehicle
speed ECU. This signal is
transmitted to the injection
system on the multiplex
network.Test the multiplex network.
Refer to fault finding for the
ABS or the vehicle speed
ECU.
New pump
chamber fillingET637: New pump
chamber fillingCOMPLETEDIf NOT DONE, see
Replacement of components.

13B-107V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
STARTING SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
+ After ignition
computer feedET001: + After ignition
computer feed.
PRESENTIndicates + after ignition feed to
the computer.
- Present
- AbsentIn the event of a fault, carry
out the fault finding
procedure for DF047
"Computer supply voltage" or
DF015 "Main relay circuit".
StartingET076: Starting.
AUTHORISEDIndicates whether or not
starting has been authorised by
the injection.
AUTHORISED: The injection
authorises starting.
PROHIBITED: The injection
does not authorise starting.If PROHIBITED, carry out
a complete fault finding
procedure on the preheating
system.
EngineET038: Engine.
RUNNINGIndicates the current status of
the engine.
- UNDER + AFTER IGNITION
FEED
- UNDER STARTER
- RUNNING
- SUPPLY MAINTAINED: Supply
maintained during the power
latch phase.
- STALLED: When the engine
has stalled.
- PROTECTED: When a fault has
appeared or when the engine
speed is locked at a certain
value.NONE
Battery
voltagePR074: Battery
voltage.13 V < PR074 < 14 VIf there is a fault, apply
the fault finding procedure for
the "Charge circuit".

13B-110V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
COLD LOOP SUB-FUNCTION (continued 1):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or
Status Check
or actionDisplay and notes Fault finding
Refrigerant
pressurePR037:
Refrigerant
pressure.Gives the value in BAR for the
refrigerant fluid in the system.
2 bar < PR037 < 27 bar
Default value: 0 barIf there is a fault apply the
fault finding procedure for
DF049 "Refrigerant sensor
circuit". If the fault is still
present, replace the
refrigerant sensor.
Engine speedPR055: Engine
speed.
Cold: 900
RPM
Warm: 805 rpm.Shows the engine's speed of rotation in
RPMIn the event of a fault, apply
the fault finding procedure for
DF005 "Engine speed sensor
circuit".
Fast idle speed
requestET023: Fast
idle speed
request.
ABSENTThe UCH requests fast idle speed from
the injection.
- ABSENT: The UCH did not make
a request.
- PRESENT: The UCH made a request.If ET023 is inconsistent, test
the multiplex network using
the diagnostic tool. If the test
is correct, consult the fault
finding procedure for the
UCH.
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90 °CIndicates the coolant temperature in °C.
Default value: 80°CIn the event of a fault, consult
the interpretation of
parameter PR064 Coolant
temperature.
Vehicle speedPR089: Vehicle
speed.Indicates the vehicle speed in mph.
This parameter is transmitted by the
ABS computer or by the vehicle speed
ECU. This signal is transmitted to the
injection system on the multiplex
network.Test the multiplex network.
Refer to fault finding for
the ABS or the vehicle speed
ECU.

13B-122V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
CRUISE CONTROL - SPEED LIMITER SUB-FUNCTION (continued 1):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or
Status Check
or actionDisplay and notes Fault finding
Brake contactET704: Brake
switch No. 1- INACTIVE
- ACTIVE (brake pedal depressed)Consult the interpretation of
status ET704 Brake switch
No. 1.
ET705: Brake
switch No. 2- ACTIVE (brake pedal released)
- INACTIVEConsult the interpretation of
status ET705 Brake switch
No. 2.
Clutch pedal
switchET405: Clutch
pedal switch- ACTIVE
- INACTIVEIn the event of a fault,
consult the interpretation of
status ET405 Clutch
switch.
Cruise control
setpointPR130: Cruise
control
setpointIndicates the reference value requested by
the driver (in mph (km/h))NONE
Vehicle speedPR089: Vehicle
speed0 mph (km/h)
Gives the vehicle speed in mph (km/h). This
parameter is transmitted by the ABS computer
or vehicle speed ECU*. This signal is
transmitted to the injection on the multiplex
network.Test the multiplex
network. See fault finding
for the ABS system or the
vehicle speed ECU*.

13B-126
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET042
CONTINUED 1
INACTIVE
When the main switch is in rest position (or neutral), status ET042 is INACTIVE.
If CRUISE CONTROL or SPEED LIMITER appears despite the main switch being in
the rest (or neutral) position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for +12 V after ignition feed on the main switch connector.
• Connection code AP43 of component 1546.
Disconnect the main switch and with it in the rest position, check the insulation
between:
• Connection code AP43 and 3FX of component 1546.
• Connection code AP43 and 3PD of component 1546.
Check the continuity between connections AP43 and 3PD of component 1546 in
the speed limiter position.
– Check the continuity between connections AP43 and 3FX of component
1546in the cruise control position.
If these checks are not in order, replace the switch.
Check the continuity, insulation, and the absence of interference resistance on
the following connections:
• Connection code 3FX,
• Connection code 3PD,
between components 1546 and 120.
Also check the engine management computer connectors.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the wiring, otherwise replace it.

13B-127
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET042
CONTINUED 2
SPEED LIMITER
When the driver presses the main switch in the speed limiter position, status
ET042becomes SPEED LIMITER.
If CRUISE CONTROL or INACTIVE appears although the switch was pressed in
the speed limiter position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for +12 V after ignition feed on the main switch connector.
• Connection code AP43 of component 1546.
Disconnect the main switch and with it in the rest position, check the insulation
between:
• Connection codes AP43 and 3FX of component 1546.
• Connection codes AP43 and 3PD of component 1546.
Check the continuity between connections AP43 and 3PD of component 1546 in
the speed limiter position.
Check the continuity between connections AP43 and 3FX of component 1546 in
the cruise control position.
If these checks show incorrect values, replace the main switch.
Check the continuity, insulation and the absence of interference resistance on
the following connections:
• Connection code 3FX,
• Connection code 3PD,
between components 1546 and 120.
Also check the engine management computer connectors.
If there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.

13B-128
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET042
CONTINUED 3
CRUISE
CONTROL
When the driver presses the main switch in the speed limiter position, status
ET042becomes SPEED LIMITER.
If CRUISE CONTROL or INACTIVE appears although the switch was pressed in
the speed limiter position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for +12 V after ignition feed on the main switch connector.
• Connection code AP43 of component 1546.
Disconnect the main switch, and when it is in the rest position, check the insulation
between:
• Connection codes AP43 and 3FX of component 1546.
• Connection codes AP43 and 3PD of component 1546.
– Check the continuity between connections AP43 and 3PD of component 1546
in the speed limiter position.
– Check the continuity between connections AP43 and 3FX of component 1546
in the cruise control position.
If these checks show incorrect values, replace the main switch.
Check the continuity, insulation and the absence of interference resistance on
the following connections:
• Connection code 3FX,
• Connection code 3PD,
Between components 1546 and 120.
Also check the engine management computer connectors.
If there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.

13B-131
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET415 CRUISE CONTROL/SPEED LIMITER DEACTIVATION
NOTESNone.
Note:
Cruise control can be activated when the vehicle speed exceeds 18 mph (30 km/h).
Status ET415 shows various reasons for deactivation of the cruise control / speed limiter function, due to a driver
request or the external environment (e.g. STATUS 1).
IMPORTANT:
Clear the fault memory by running command RZ001 Fault memory, to reset this status to NONE.
NONEThis status is present on the diagnostic tool if:
the computer has been reinitialised,
the computer has been reprogrammed.
STATUS 1Traction control request
If the vehicle is fitted with a traction control system, the cruise control function is
deactivated every time the ABS computer calls for traction control.
Status ET415 becomes STATUS 1 when driving with the cruise control active
(ET042 Cruise control/Speed limiter: CRUISE CONTROL) and traction control is
requested.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 1 without traction control requested (see 38C,
ABS).
DDCR_V44_ET415/DDCR_V48_ET415

13B-135
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET415
CONTINUED 4
STATUS 6
Gear lever in neutral (manual gearbox) or the neutral position
(automatic gearbox)
Status ET415 becomes STATUS 6 when driving with cruise control active
(ET042 Cruise control - speed limiter: CRUISE CONTROL) and:
– if the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
– if the gear lever is put in neutral on an automatic transmission.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on
a manual gearbox without declutching, or into the neutral position on an automatic
transmission, run fault finding on the ABS computer and check the configuration of
the tyre size stored in the computer. If the configuration is correct, contact the
Techline.
STATUS 7Inconsistency between the request and the vehicle speed
Status ET415 becomes STATUS 7 if the computer detects too great a difference
between the speed requested by the driver and the vehicle speed.
This could occur when driving with cruise control active (ET042 Cruise control/
speed limiter: CRUISE CONTROL) and when there is a significant difference in
speed.
This inconsistency deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 7 on relatively flat terrain, contact the Techline.

13B-136
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET415
CONTINUED 5
STATUS 8
Automatic transmission in defect mode.
NOT AVAILABLE ON THIS SOFTWARE
STATUS 9Vehicle speed monitoring
Status ET415 becomes STATUS 9 if the vehicle speed received by the computer is
invalid or absent.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then run fault finding on the ABS computer.
Deal with the present or stored faults (see 38C, ABS).
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If the specification STATUS 9 is still present, contact Techline.
STATUS 10Monitoring by injection computer
Status ET415 becomes STATUS 10 when driving with cruise control active
(ET042 Cruise control - speed limiter: CRUISE CONTROL) and if the injection
computer detects a fault anywhere in the engine management system, or an engine
speed that is too high or too low.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then Perform fault finding on the injection
computer.
Deal with any present or stored faults (see 13B, Diesel injection).
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If STATUS 10 is still present, contact the Techline.