RENAULT TWINGO 2009 2.G Engine And Peripherals Workshop Manual

12B-16
TURBOCHARGING
Turbocharger oil pipe: Removal - Refitting
C44, and K9K
12B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove the front engine cover.
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
1 - Turbocharger oil supply pipe
aRemove:
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the air filter box (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the exhaust gas recirculation solenoid valve (see
14A, Antipollution, Exhaust gas recirculation
solenoid valve: Removal - Refitting, page 14A-
10) .
2 - turbocharger oil return pipe
aRemove the catalytic converter (see 19B, Exhaust,
Catalytic converter: Removal - Refitting, page
19B-12) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
1 - Turbocharger oil supply pipe
aRemove the bolt (1) of the turbocharger oil supply
pipe from the turbocharger.
aUndo the nut (2) of the turbocharger oil supply pipe
on the cylinder head.
aRemove the nut of the turbocharger oil supply pipe
on the cylinder head.
aRemove the turbocharger oil supply pipe. Special tooling required
Mot. 1746Offset wrench for tightening
High Pressure pump pipes.
Tightening torquesm
nut of the oil supply pipe
on the cylinder head35 Nm
bolt of the turbocharger
oil supply pipe on the
turbocharger14 Nm
turbocharger oil return
pipe bolts12 N.m
127900
127898

12B-17
TURBOCHARGING
Turbocharger oil pipe: Removal - Refitting
C44, and K9K
12B
2 - Oil return pipe
aRemove the bolts (3) of the oil return pipe from the
turbocharger.
aIn the direction of the arrows, rotate the oil return
pipe of the turbocharger to facilitate its removal.
aRemove the turbocharger oil pipe from the cylinder
block.
REFITTING
I - REMOVAL PREPARATION OPERATION
aAlways replace:
-the turbocharger oil supply pipe,
-the flat seal of the oil return pip on the turbocharg-
er,
-the O-ring of the oil return pip on the turbocharger.
aLubricate the O-ring of the oil return pipe on the tur-
bocharger with engine oil.
II - REFITTING OPERATION FOR PART
CONCERNED
1 - Turbocharger oil supply pipe
aFit the turbocharger oil supply pipe.
aRefit:
-the turbocharger oil supply pipe nut on the cylinder
head,-the bolt of the turbocharger oil supply pipe onto the
turbocharger.
aTorque tighten:
-the nut of the oil supply pipe on the cylinder
head ( 35 Nm) using the (Mot. 1746),
-the bolt of the turbocharger oil supply pipe on
the turbocharger (14 Nm).
2 - turbocharger oil return pipe
aFit the oil return pipe on the cylinder block.
aRefit the turbocharger oil return pipe bolts.
aTorque tighten the turbocharger oil return pipe
bolts (12 N.m).
III - FINAL OPERATION.
1 - Turbocharger oil supply pipe
aRefit:
-the exhaust gas recirculation solenoid valve (see
14A, Antipollution, Exhaust gas recirculation
solenoid valve: Removal - Refitting, page 14A-
10) ,
-the air filter box (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing).
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
2 - turbocharger oil return pipe
aRefit the catalytic converter (see 19B, Exhaust,
Catalytic converter: Removal - Refitting, page
19B-12) .
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aRefit the engine cover.
127899

12B-18
TURBOCHARGING
Intercooler: Removal - Refitting
D4F, and 780 or 782 – K9K, and 718
12B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the intercooler bolts (1) .
aLoosen the clip on the intercooler air outlet pipe (2) .
aDisconnect the intercooler air outlet pipe.
aUnclip the turbocharger air outlet pipe (3) .
aDisconnect the turbocharger air outlet pipe.
aRemove:
-the intercooler,
-the air deflector clips,
-the air deflector,
-the metal mounting.
REFITTING
I - REFITTING PREPARATION OPERATION
aCheck that the intercooler is not full of oil. In this
case, clean it with cleaning agent and let it dry (see
Vehicle: Parts and consumables for the repair)
(04B, Consumables - Products).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the metal mounting,
-the air deflector,
-the air deflector clips,
-the intercooler.
aConnect the turbocharger air outlet pipe.
aClip on the turbocharger air outlet pipe.
aConnect the intercooler air outlet pipe.
aTighten the clip on the intercooler outlet pipe.
aRefit the intercooler bolts.
III - FINAL OPERATION
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
122830

13A-1
FUEL SUPPLY
Diesel supply circuit: Operating diagram
K9K
13A
The diesel fuel supply system includes a diesel injec-
tion computer and various sensors.
120417
(1) Fuel tank
(2) Dipstick
(3) Electrical diesel fuel reheater
(4) Man ual priming pump
(5) Diesel filter
(6) High pressure pump
(7) Fuel fl ow actuator
(8) Injector rail
(9) Injector rail pressure sensor
(10) Diesel injector
(11) Venturi
IMPORTANT
Loosening a high pressure pipe union when the
engine is running is strictly prohibited.
WARNING
It is forbidden:
-to dismantle the interior of the pump or injectors.
-to remove the pressure sensor from the fuel rail
(because of circuit contamination problems). If the
pressure sensor fails, the pressure sensor, the rail
and the five high pressure pipes must be replaced,
-to dismantle the flow regulator solenoid valve and
the pressure regulator solenoid valve on the high
pressure pump.

13A-2
FUEL SUPPLY
Manual priming pump: Removal - Refitting
K9K
13A
PARTS AND CONSUMABLES FOR THE
REPAIR WORK
aCONSUMABLES:
-cleaning cloths.
a
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aRemove the front engine cover.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDetach the fuel pipe from the body.
aDisconnect the electric diesel fuel heater fuel pipe
union (1) .
aUnclip the fuel pipe. IMPORTANT
During this operation, be sure to:
-refrain from smoking or bringing red hot objects
close to the working area,
-be careful of fuel splashes when disconnecting
the union.
IMPORTANT
Wear goggles with side protectors for this opera-
tion.
IMPORTANT
Wear latex gloves during the operation.
IMPORTANT
Consult the safety and cleanliness advice and
operation recommendations before carrying out
any repair (see 13B, Diesel injection, Diesel
injection: Precautions for the repair, page
13B-1) .
WARNING
To avoid any corrosion or damage, protect the
areas on which fuel is likely to run.
WARNING
Prepare for the flow of fluid, and protect the sur-
rounding components.
120049
WARNING
To prevent impur ities from entering the circuit,
plugs must be fitted to the openings of all the fuel
circuit components exposed to the open air.
WARNING
Keep the pipe unions away from contaminated
areas.

13A-3
FUEL SUPPLY
Manual priming pump: Removal - Refitting
K9K
13A
aDisconnect the fuel pipe union (2) .
aRemove the manual priming pump.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
a
aRefit the manual priming pump.
aConnect the fuel pipe union.
aClip on the fuel pipe.
aConnect the fuel pipe union to the electric diesel fuel
heater.
aClip the fuel pipe on to the body.
II - FINAL OPERATION.
aOpen the bleed screw on top of the fuel filter.
aPrime the fuel circuit using a manual priming pump
until the disconnected pipes are filled with fuel.
aClose the bleed screw on top of the fuel filter.aCheck that there are no fuel leaks.
aStart the engine.
aCheck that there are no fuel leaks.
aSwitch off the engine.
aRefit the engine cover.
120045
WARNING
Do not remove the blanking plugs from each
component until the last moment.
Also, do not remove the components from their
packaging until they are to be fitted to the vehi-
cle.

13A-4
FUEL SUPPLY
Fuel filter: Removal - Refitting
K9K
13A
PARTS AND CONSUMABLES FOR THE
REPAIR WORK
aCONSUMABLES:
-cleaning cloths.
aMake sure you have a new diesel filter before open-
ing the fuel circuit.
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the front engine cover.aDisconnect the fuel filter:
-the high pressure pump inlet pipe (1) ,
-the manual priming pump outlet pipe (2) .
aRemove the fuel supply pipes (1) and (2) . IMPORTANT
During this operation, be sure to:
-refrain from smoking or bringing red hot objects
close to the working area,
-be careful of fuel splashes when disconnecting
the union.
IMPORTANT
Wear goggles with side protectors for this opera-
tion.
IMPORTANT
Wear latex gloves during the operation.
IMPORTANT
Consult the safety and cleanliness advice and
operation recommendations before carrying out
any repair (see 13B, Diesel injection, Diesel
injection: Precautions for the repair, page
13B-1) .
Note:
Periodically bleed the water contained in the die-
sel filter via the bleed screw (see maintenance
handbook for vehicle concerned).
WARNING
To avoid any corrosion or damage, protect the
areas on which fuel is likely to run.
121441
WARNING
Prepare for the flow of fluid, and protect the sur-
rounding components.
WARNING
To prevent impur ities from entering the circuit,
plugs must be fitted to the openings of all the fuel
circuit components exposed to the open air.
WARNING
Keep the pipe unions away from contaminated
areas.

13A-5
FUEL SUPPLY
Fuel filter: Removal - Refitting
K9K
13A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the fuel filter mounting nut (3) ,
-the fuel filter from its mounting.
aDetach the water detection sensor offset connector
on the fuel filter mounting (if fitted).
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aaAttach the water detection sensor offset connector
to the fuel filter mounting (if fitted).
aRefit the fuel filter to its mounting.
aFit the fuel filter mounting nut.
II - FINAL OPERATION.
aPosition the fuel pipes.
aConnect to the fuel filter:
-the manual priming pump outlet pipe,
-the high pressure pump inlet pipe.
aOpen the bleed screw on top of the fuel filter.
aPrime the fuel circuit using a manual priming pump
until the disconnected pipes are filled with fuel.
aClose the bleed screw on top of the fuel filter.
aCheck that there are no fuel leaks.
aStart the engine.
aCheck that there are no fuel leaks.
aSwitch off the engine.
aRefit the engine cover.
BLEEDING
aRemove the fuel filter mounting nut.
aDetach the manual priming pump.
aRemove the fuel filter without pulling on the water
detection sensor wiring harness in the diesel fuel.
aPosition a container under the fuel filter which has
been removed from its mounting.
aTurn the bleed cap or the water detection sensor in
the diesel fuel (depending on equipment) by no
more than one turn.
aAllow it to flow until diesel fuel appears.
aClose the bleed cap or the water detection sensor
(depending on equipment).
121441
Note:
If the fuel filter is to be reused, fit blanking plugs
to the fuel supply pipes and fuel filter openings,
using the appropriate blanking plug kit, depend-
ing on the engine (see 13B, Diesel injection,
Diesel injection: Precautions for the repair,
page 13B-1) .
WARNING
Do not remove the blanking plugs from each
component until the last moment.
Also, do not remove the components from their
packaging until they are to be fitted to the vehi-
cle.
Note:
Chec k that the fuel filter is correctly positioned
and secure on its mounting by shaking it: the fil-
ter must not move.
WARNING
Prepare for the flow of fluid, and protect the sur-
rounding components.

13A-6
FUEL SUPPLY
Fuel filter: Removal - Refitting
K4M
13A
The fuel filter is incorporated in the "fuel level sensor
module". To remove the fuel filter, remove the "fuel lev-
el sensor module" (see 19C, Tank, Fuel level sensor
module: Removal - Refitting, page 19C-13) .

13A-7
FUEL SUPPLY
Electric diesel fuel heater: Removal - Refitting
C44, and K9K
13A
REMOVAL
I - OPERATION FOR REMOVAL OF PART
CONCERNED
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) ).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the electric diesel fuel heater electrical
connector (1) .
aRemove the nut (2) from the electric diesel fuel heat-
er mounting on the body.
aDisconnect the inlet and outlet fuel supply pipes (3)
from the electric diesel fuel heater.
aRemove the electric diesel fuel heater and its mount-
ing from the vehicle.
aSeparate the electric diesel fuel heater from its
mounting, letting it flow.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aFit then lock the electric diesel fuel heater to its
mounting.
aFit the electric diesel fuel heater and its mounting to
the vehicle.
aConnect the electric diesel fuel heater inlet and out-
let fuel supply pipes.
aRefit the electric diesel fuel heater mounting nut on
the body.
aTighten the diesel heater mounting nut on the body.
aConnect the electric diesel fuel heater electrical con-
nector.
aPrime the diesel circuit using the manual priming
pump (4) .
aStart the engine then let it run for a few minutes to
check that it starts properly and to check that there
are no leaks.
II - FINAL OPERATION.
aDeal with possible fuel leaks.
120049
Note:
Make preparations for fuel outfl ow.
120045