RENAULT TWINGO 2009 2.G Engine And Peripherals Workshop Manual

17A-5
IGNITION
Coils: Removal - Refitting
D4F, and 780 or 782
17A
Tightening torquesm
ignition coil bolts10 N.m

17A-6
IGNITION
Coils: Removal - Refitting
D4F, and 780 or 782
17A
REMOVAL
OPERATION FOR REMOVAL OF PART
CONCERNED
a
aRemove the turbocharger air outlet pipe bolt (3) from
the throttle valve.aDetach the turbocharger air outlet pipe from the tur-
bocharger in the direction of the arrow (4) .
aDisconnect the turbocharger air outlet pipe from the
turbocharger.
aMove aside the turbocharger air outlet pipe.
122833
122673
Note:
If the turbocharger air outlet pipe tightening clip
(1) is removed, the flexible rubber pipe (2) and
the tightening clip (1) must be replaced.
Note:
If the clip (5) is removed from the heat resistant
protector, the latter must be replaced.

17A-7
IGNITION
Coils: Removal - Refitting
D4F, and 780 or 782
17A
aDisconnect:
-the ignition coil connector (6) ,
-the spark plug lead high-tension caps (7) from the
ignition coil.
aRemove:
-the bolts (8) from the ignition coil,
-the ignition coil.
120958
120958

17A-8
IGNITION
Coils: Removal - Refitting
D4F, and 780 or 782
17A
REFITTING
I - REFITTING PREPARATION OPERATION
aIt is essential to apply a bead of FLUOSTAR 2L
(see Vehicle: Parts and consumables for the re-
pair) (04B, Consumables - Products) with a diame-
ter of 2 mm to the inner edge of the high-tension
caps on the ignition coil side.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the ignition coil,
-the ignition coil bolts.
aTorque tighten the ignition coil bolts (10 N.m).
aCheck the spark plug leads and the ignition coil
match.
aConnect:
-the spark plug lead high-tension caps to the ignition
coil,
-the ignition coil connector.
106640

17A-9
IGNITION
Coils: Removal - Refitting
D4F, and 780 or 782
17A
aPush the turbocharger air outlet pipe clip (9) .
aConnect the turbocharger air outlet pipe to the turbo-
charger.
aRefit the turbocharger air outlet pipe bolt to the throt-
tle valve.
aTighten the turbocharger air outlet pipe bolt on the
throttle valve.
122666

17A-10
IGNITION
Coils: Removal - Refitting
K4M
17A
REMOVAL
OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the coil connectors (1) .aRemove:
-the coil bolts (2) ,
-the coils. Tightening torquesm
new coil bolts14 N.m
132431
132432

17A-11
IGNITION
Coils: Removal - Refitting
K4M
17A
REFITTING
I - REFITTING PREPARATION OPERATION
aPut a beadof FLUOSTAR 2L (see Vehicle: Parts
and consumables for the repair) (04B, Consum-
ables - Products) 2 mm in diameter on the internal
perimeter of the high-tension caps on the four coils.
aAlways replace the coil bolts.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the coils.
aTorque tighten the new coil bolts (14 N.m).
aConnect the coil connectors.
106443

17A-12
IGNITION
Plugs: Removal - Refitting
D7F
17A
Spark plug electrode gap
REMOVAL
OPERATION FOR REMOVAL OF PART
CONCERNED
a
aDisconnect the spark plug wiring.
aRemove the spark plugs using the (Ele. 1933)
equipped with the (Ele. 1382-01).
REFITTING
I - REFITTING PREPARATION OPERATION
aCheck and, if necessary, correct the spark plug elec-
trode gaps using a set of feeler gauges. Special tooling required
Ele. 193323 N.m tightening wrench for
spar k plugs
Ele. 1382-0114 mm Plug spanner.
Tightening torquesm
spar k plugs23 N.m
Type of spark plug Gap (mm)
EYQUEM 0.90 ± 0.05
WARNING
To disconnect the spark plug leads, pull on the
extensions and not on the leads.
121730

17A-13
IGNITION
Plugs: Removal - Refitting
D7F
17A
aWhen refitting the ignition wiring harness, it is essen-
tial to apply a bead of FLUOSTAR 2L (2 mm in di-
ameter) to the internal edge of the high tension caps
on the spark plug and coil sides (see Vehicle: Parts
and consumables for the repair) (04B, Consum-
ables - Products).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the spark plugs.
aTorque tighten the spark plugs (23 N.m) using the
(Ele. 1933) fitted with the (Ele. 1382-01).
III - FINAL OPERATION
aConnect the spark plug wiring.
106640

17A-14
IGNITION
Plugs: Removal - Refitting
D4F, and 780 – D4F, and 782
17A
Spark plug electrode gap
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the air filter box cover bolts (1) .
aRemove the air filter box cover and the air filter box
air inlet pipe.II - OPERATION FOR REMOVAL OF PART
CONCERNED
a
Disconnect the spark plug ignition wiring harnesses
(5) .
aRemove the spark plugs using the (Ele. 1933)
equipped with the (Ele. 1382-01).
REFITTING
I - REFITTING PREPARATION OPERATION
aCheck and, if necessary, correct the spark plug elec-
trode gaps using a set of feeler gauges. Special tooling required
Ele. 193323 N.m tightening wrench for
spar k plugs
Ele. 1382-0114 mm Plug spanner.
Equipment required
set of feeler gauges
Tightening torquesm
spar k plugs23 N.m
Type of spark plug Gap (mm)
NGK 0.65 ± 0.05
122836
120958
WARNING
To disconnect the spark plug leads, pull on the
extensions and not on the leads.