SAAB 9-5 2006 Owners Manual
Page 181 of 288
181 Starting and driving
Driving with a roof rack 
loadThe maximum permissible roof load is 
220 lbs. (100 kg). 
Note that the roof load is included in the 
car’s maximum permissible load (see 
page 260).
Strong, sturdy roof carriers designed spe-
cially for the car are available from your 
Saab dealer. Always secure the roof load 
safely. 
Fitting the roof carriers
 , 
9-5 Sedan and 9-5 SportCombi 
without roof railsThe carrier feet are marked with a top view 
of the car and arrow indicating their posi-
tions. 
1 Slip the plastic cover onto the adjustable 
foot of the carrier (foot with knob for tight-
ening) to protect the paintwork during 
assembly. 
2 Open all the doors.
Fold back the rubber strip and find the 
fixing holes. 3 Start on the left-hand side of the car.
Rest the carrier carefully across the roof, 
with the rigid foot towards you. Hold the 
foot clear of the roof to avoid damaging 
the paintwork.
Fold back the rubber strip and insert the 
pins on the foot into the fixing holes. 
Make sure that the rubber strip comes 
inside the plastic cover on the carrier. 
Repeat the procedure with the other 
carrier.
WARNING
 A roof load will affect the car’s center 
of gravity and aerodynamics. Be 
aware of this when cornering and driv-
ing in crosswinds.
 Suit your speed to the prevailing con-
ditions.
 Due to higher aerodynamic drag, fuel 
economy may suffer when driving with 
a roof rack.
IB480
IB481
95usM06.book  Page 181  Thursday, November 17, 2005  8:59 AM
ProCarManuals.com 
Page 182 of 288
182 Starting and driving4 Close the doors on the left-hand side of 
the car gently, to hold the carrier feet in 
place. 
5 Now go around to the other side of the 
car and remove the plastic cover from 
the carrier’s adjustable foot. Fold back 
the rubber strip and insert the pins on 
the foot into the fixing holes. Do the 
same with the other carrier and close the 
doors gently. 
6 Tighten each carrier by turning the knob 
clockwise (by hand). Tighten just 
enough to bring the foot up against the 
edges of the fixing holes. 
Remove the carriers when not in use, as 
they increase fuel consumption. 
The instructions that accompany the carri-
ers also include advice on driving with a roof 
load – we strongly recommend that you 
read them carefully. 
Fitting the roof carriers
 , 
9-5 SportCombi with roof rails1 Clean the car’s roof rails.
2 Check the markings on the cross mem-
bers to see which is the front and which 
is the rear roof carrier.
3 Place the cross members on the roof 
rails, on their respective sides of the 
center supports. The cross members 
must not be placed beyond the front or 
rear joint on the rail. Ensure that the dis-
tance between the cross members is at 
least 28 inches (700 mm).
If a roof box is to be fitted, the cross 
members must be positioned so that the 
tailgate can be opened fully without hit-
ting the roof box.
4 Using your thumb, press the bracket so 
that it lies snugly against the outside of 
the roof rail. Make sure that the roof car-
riers are seated centrally on the rubber 
spacers and that these sit correctly on 
the roof rail. Pull the spacers down 
slightly on the inside of the roof rail.
5 Center the roof carriers so that they pro-
trude equally on both sides.
6 Tighten the roof carriers by hand. 
Ensure that the tightening knobs are 
upright once the roof carriers have been 
tightened.
7 Make sure the roof carriers are securely 
in place.
IB1294
95usM06.book  Page 182  Thursday, November 17, 2005  8:59 AM
ProCarManuals.com 
Page 183 of 288
183 Starting and driving
Driving at nightBear in mind the following points when 
driving at night:
 Nighttime driving requires your full con-
centration.
 Do not rush. Count on your journey taking 
slightly longer.
 The number of drivers under the influence 
of drugs is likely to be greater at night than 
during the day.
 Do not stare at the headlights of oncom-
ing vehicles.
 Avoid driving at night if you have poor eye-
sight. Night vision deteriorates with age.
 Keep your car's headlights, windows and 
mirrors clean. Also, if you wear glasses, 
make sure they are clean.
 Make sure you are well rested before 
starting a long journey. Take a break every 
other hour.
 Only eat light meals. Heavy meals have a 
tendency to induce tiredness.
Driving with a loadThe driving characteristics of the car are 
affected by the way it is loaded.
 Place heavy loads as far forward and as 
low as possible in the trunk.
 Secure the load to the tie downs, see 
page 132.
 The load should be such that the car´s 
total weight or axle weight are not 
exceeded, see page 260.
 Heavy loads mean that the car’s center of 
gravity is further back. As a result, the car 
will sway more during evasive steering.
 Never exceed the permissible load in the 
roof box, even if there is room for more.
 Ensure that the tire pressure is correct – 
slight overinflation is preferable to under-
inflation.
 The braking distance of a loaded car is 
always greater. Keep your distance from 
the vehicle in front.
 Roof loads can negatively affect tele-
communication.
Tire pressure, see page 270 and back 
cover.
IB1295
95usM06.book  Page 183  Thursday, November 17, 2005  8:59 AM
ProCarManuals.com 
Page 184 of 288
184 Starting and drivingTires 
The tire pressure should match the current 
load and speed of the car; for cars sold in 
U.S. see page 234; for cars sold in Canada 
see page 269.
The tire pressures given apply to cold tires, 
that is tires that are the same temperature 
as the outside air temperature.
The tire pressure increases as the tires 
become warm (e.g. during highway driving) 
with approximately 0.3 bar (4 psi). When 
the temperature of the tires changes by 50° 
(10°C), the tire pressure will change 0.1 bar 
(2 psi).Never reduce the pressure of a hot tire. If the 
tires are hot when you check them, only 
increase the pressure, if necessary.
Underinflated tires wear more quickly than 
slightly overinflated tires.
If a valve is leaking, simply unscrew it and fit 
a new one.
Important! Remember to adjust the tire 
pressures if you change the load in the car 
or intend to drive at substantially lower or 
higher speeds than normal.
WARNING
Check the tire pressure at least once a 
month and before long journeys. Under-
inflation can result in:
 Punctures
 Separation of the tire and tread
 Damage to the sidewalls
 Damage to the rims on poor roads
 Poor handling characteristics
 Premature tire wear
 Increased fuel consumption.95usM06.book  Page 184  Thursday, November 17, 2005  8:59 AM
ProCarManuals.com 
Page 185 of 288
185 Starting and driving
Driving with a spare 
wheel fittedSee page 238.Driving with the trunk 
lid/tailgate openAvoid driving with the trunk lid/tailgate partly 
or fully open, since exhaust fumes can be 
drawn into the cabin.
If you must drive with the trunk lid/tailgate 
open, all windows and the moonroof must 
be closed and the cabin fan on at its highest 
speed setting.
Driving in deep water Towing the carNOTICEDo not drive in water deeper than 
12 inches (30 cm) and do not drive faster 
than 3–4 mph. Water can otherwise be 
sucked into the engine. The engine will be 
seriously damaged if water enters the 
intake system.
WARNING
 Remember that the brake servo does 
not operate when the engine is off. 
Much greater pressure than normal 
will therefore be required to operate 
the brake pedal. 
 Nor does the steering servo operate 
when the engine is off. The steering 
will therefore be much heavier than 
usual. 
 The towing vehicle should always be 
heavier than the vehicle on tow. 
 Never allow passengers to ride in the 
car being towed. 
 Always seek professional help if the 
car needs to be towed.
95usM06.book  Page 185  Thursday, November 17, 2005  8:59 AM
ProCarManuals.com 
Page 186 of 288
186 Starting and drivingFront towing eye 
The front towing eye is stored with the spare 
wheel. 
The attachment point (tapped hole) for the 
towing eye is midway along the engine sub-
frame at the front of the car. 
Remove the plastic plug and screw in the 
towing eye securely. 
To ensure that the towing eye is in far 
enough, insert the handle of the wheel 
wrench through the eye for additional 
leverage.
Rear towing eyeThe car has a permanently mounted towing 
eye at the back. If the car is equipped with a 
trailer hitch, this can be used instead of the 
towing eye. 
WARNING
 Make sure that the towing eye at the 
front is screwed in tightly. 
 The towing eye is only designed for 
use when the car is being towed on the 
road. It must not be used to pull the 
car out of a ditch, for example. 
 Make sure that all bystanders keep a 
suitable distance, in case the towing 
eye or tow rope should break. The 
towing eye or tow rope could catapult 
off and cause serious injury.NOTICE Do not drive the car with the front 
towing eye in position. If it catches the 
curb, for example, the engine sub-
frame could be damaged. 
 Refit the plastic plug in the hole when 
the towing eye has been removed, to 
keep dirt and moisture out of the 
threads.
IB3885
Front towing eye 
IB3886
Rear towing eye 
95usM06.book  Page 186  Thursday, November 17, 2005  8:59 AM
ProCarManuals.com 
Page 187 of 288
187 Starting and driving
Towing the car Gear lever in neutral (in cars with automatic 
transmission: selector lever at N (neutral)) 
Turn on the parking lights.
Drive carefully and do not exceed the 
speed limit for vehicles being towed. 
Always try to keep the towrope taut by 
gently applying the brake, as necessary. 
This will avoid the towrope being jerked 
violently.
The local regulations on towing speeds 
must be followed.
The highest permissible towing speed is 
30 mph (50 km/h), unless the legal limit is 
lower. The longest permissible towing dis-
tance is 30 miles (50 km). If the car has to 
be transported farther than that, summon a 
tow truck. A flat bed tow truck is the pre-
ferred method to tow.
Failure to follow these guidelines can result 
in damage.Cars with automatic transmission
The car cannot be push started. In an emer-
gency, it is possible to start the engine using 
jump leads (see the section, ”Jump starting” 
on page 188).
Transporting the car 
NOTICENever use the towing eyes to pull the 
car unstuck.
NOTICE The car must be towed front first.
 If the car is to be towed with the front 
wheels off the ground, make sure the 
parking brake is off, as this acts on the 
rear wheels. 
NOTICEIf a car with a sport (lowered) chassis is 
transported, for example on a flat bed 
truck, take extra care not to damage the 
spoiler and/or underbody.
Never use the towing eyes to pull the car 
unstuck
95usM06.book  Page 187  Thursday, November 17, 2005  8:59 AM
ProCarManuals.com 
Page 188 of 288
188 Starting and drivingJump startingIf your battery has run down, you may want 
to use another vehicle and some jumper 
cables to start your Saab. Follow the steps 
below to do it safely.To jump start your vehicle:
1 Check the other vehicle. It must have a 
12-volt battery with a negative ground 
system.
2 Get the vehicles close enough so the 
jumper cables can reach, but be sure the 
vehicles are not touching each other. If a 
poor connection on the negative jumper 
cable should exist, it is possible for 
damage to be caused to electrical sys-
tems/components of either vehicle 
should inadvertent contact be made. 
You would not be able to start your car 
and bad grounding could damage elec-
trical systems.
3 Turn off the ignition on both vehicles. 
Turn off all lights that are not needed, 
and radios. This will avoid sparks and 
help save both batteries and it could 
save your radio.
WARNING
 When working on the battery, highly 
explosive gas can build up. A spark 
could ignite this gas that collects 
around the battery.
Therefore, always avoid sparks and 
open flames in the vicinity of the bat-
tery.
 The battery contains corrosive sulfuric 
acid. Always wear a face mask or gog-
gles when working on the battery.
 If battery acid gets into the eyes or 
splashes onto skin or clothing, wash 
the affected area liberally with water.
If acid gets into the eyes or a large 
quantity makes contact with the skin, 
seek medical help.
 Battery posts, terminals and related 
accessories contain lead and lead 
compounds. Wash your hands after 
handling.
NOTICEIgnoring these steps could result in costly 
damage to your vehicle that would not be 
covered by your warranty.
Trying to start your car by pushing or pull-
ing it could damage your vehicle, even if 
you have a manual transmission. If you 
have an automatic transmission, your 
vehicle cannot be started by pushing or 
pulling it.
NOTICEIf the other system is not a 12-volt system 
with a negative ground, both vehicles can 
be damaged.
WARNING
You could be injured if the vehicles roll. 
Set the parking brake firmly on each vehi-
cle. Put an automatic transmission in P 
(Park) or a manual transmission in 
Neutral.
IB3931
95usM06.book  Page 188  Thursday, November 17, 2005  8:59 AM
ProCarManuals.com 
Page 189 of 288
189 Starting and driving
4 Open the hood and locate the battery.
Find the positive (+) and negative (–) termi-
nals on the battery.5 Check that the jumper cables do not 
have loose or missing insulation. If they 
do, you could get a shock and also the 
vehicles could be damaged.
Before you connect the cables, here are 
some basic things you should know. 
Positive (+) will go to positive (+) and 
negative (–) will go to a major metal 
engine part with a good ground. Do not 
connect (+) to (–) or you will get a short 
that could injure you or would damage 
the battery and maybe other parts as 
well.
6 Connect the red positive (+) cable to the 
positive (+) terminal of the vehicle with 
the discharged battery.
7 Do not let the other end touch metal. 
Connect it to the positive (+) terminal of 
the good battery. Use a remote positive 
(+) terminal if the vehicle has one.
8 Now connect the black negative (–) 
cable to the good battery’s negative 
terminal.NOTICEIf you leave your radio on, it could be 
badly damaged. The repairs would not be 
covered by your warranty.
WARNING
An electric fan can start up even when the 
engine is not running and can injure you. 
Keep hands, clothing and tools away from 
any underhood electric fan.
WARNING
Using a match or flame of any kind near a 
battery can cause battery gas to explode. 
You can suffer burns or be blinded. Use a 
flashlight if you need more light.
Be sure the battery has enough water. 
The battery installed in your new Saab 
has filler caps. Be sure the right amount 
of water is there. Add distilled or boiled 
water if the level is too low. If you don’t, 
explosive gas could be present.
Be sure the electrolyte in the battery is not 
frozen. Discharged batteries will freeze. 
When connecting jumper cables to a 
frozen battery, gas from the chemical 
reaction inside the battery can build up 
under the ice and cause an explosion.
Battery fluid contains acid that can burn 
you. Do not get it on you. If you acciden-
tally get it in your eyes or on your skin, 
flush the area with water and get medical 
help immediately.
95usM06.book  Page 189  Thursday, November 17, 2005  8:59 AM
ProCarManuals.com 
Page 190 of 288
190 Starting and driving9 Attach the cable at least 18 inches 
(45 cm) away from the discharged bat-
tery, but not near engine parts that 
move. To avoid an arc which could deto-
nate the hydrogen gas around the bat-
tery, the final connection must be at least 
18” from the battery.
10 Start the vehicle with the good battery 
and run the engine for a while.
11 Try to start the vehicle with the dis-
charged battery. If it does not start after 
a few tries, it probably needs service.
12 Remove the cables in reverse order to 
prevent electrical shorting. Take care 
that they do not touch each other or any 
other metal.
Charging the battery/Jump 
startingTo avoid damaging the car’s electrical 
system and electronics, the following rules 
must be followed when charging the battery 
or jump starting the car.
 If the charger or starter unit can be 
set to different voltages 
(6V/12V/18V/24V), 12V must be 
selected.
 Follow the manufacturer’s instructions 
supplied with the charger or starter unit.
 Nothing that is plugged into an electrical 
outlet should be connected to the car 
during charging or jump starting.
 The charger or starter unit must under no 
conditions produce a voltage greater 
than:
 16V continuous
 18V for 60 min.
 If you are unsure about the charge rating 
of the unit, disconnect the battery clamp 
from the positive terminal before connect-
ing the unit to the battery.
WARNING
Do not let the other end touch anything 
until the next step. The other end of the 
negative cable does not go to the dead 
battery. It goes to a major metal part with 
a good ground on the engine of the vehi-
cle with the discharged battery.95usM06.book  Page 190  Thursday, November 17, 2005  8:59 AM
ProCarManuals.com