ignition SAAB 9-7X 2007 User Guide

Page 94 of 498

Delayed Locking
This feature delays the locking of the doors and
the liftgate when using the power lock or the
remote keyless entry system.
The rst press of the power door lock switch or
lock button on the remote keyless entry transmitter
with the driver’s door open will activate the
delay locking. A chime will sound. All doors and
the liftgate can be reopened for up to ve seconds
from the time the last door is closed.
Five seconds after the last door is closed, all the
doors will lock. You can lock the doors
immediately by using the power door lock switch
or by pressing the lock button on the optional
remote keyless entry transmitter a second time.
If the key is inserted in the ignition, this feature will
not lock the doors. SeeLockout Protection on
page 97.
You can turn the delayed locking feature on or off.
If the feature is turned off, the doors will lock
immediately when a power door lock switch or
remote keyless entry transmitter lock button
is pressed.
Programming Delayed Locking
To turn the delayed locking feature on or off, do
the following:
1. Press and hold the power door lock switch on
the driver’s door in the lock position.
2. Press the remote keyless entry transmitter
unlock button twice.
If the delayed locking feature was on, it will now
be off. If the feature was off, it will now be on.
Programmable Automatic
Door Locks
Your vehicle is equipped with an automatic
lock/unlock feature which enables you to program
your vehicle’s power door locks. You can
program this feature through the Driver Information
Center (DIC), or by the following method. See
DIC Vehicle Customization on page 205.
94
ProCarManuals.com

Page 95 of 498

Programmable Locking Feature
Following are the two locking modes that can be
programmed:
Mode 1:All doors lock when the transmission is
shifted out of PARK (P).
Mode 2:All doors lock when the vehicle speed is
greater than 8 mph (13 km/h).
The automatic door locks were pre-programmed at
the factory to lock all the doors when the
transmission is shifted into gear. The following
instructions detail how to program your door
locks differently than the factory setting. Choose
one of the two programming options listed
previously before entering the program mode.
To enter the program mode, do the following:
1. Begin with the ignition off. Then pull the turn
signal/multifunction lever toward you and hold
it there while you perform the next step.
2. Turn the key to RUN and LOCK twice. Then,
with the key in LOCK, release the turn
signal/multifunction lever. Once you do this,
you will hear the lock switch lock and
unlock, the horn will chirp twice, and a
30-second program timer will begin.3. You are now ready to program the automatic
door locks. Select one of the two programming
options listed previously, and press the lock
side of the power door lock switch to
cycle through the lock options. You will have
30 seconds to begin programming. If you
exceed the 30-second limit, the locks
will automatically lock and unlock and the
horn will chirp twice to indicate that you have
left the program mode. If this occurs,
repeat the procedure beginning with Step 1 to
re-enter the programming mode.
You can exit the program mode any time by
turning the ignition to RUN. The locks will
automatically lock and unlock and the horn will
chirp twice to indicate that you are leaving
the program mode. If the lock/unlock switches are
not pressed while in the programming mode,
the current auto lock/unlock setting will not
be modied.
See your dealer for more information.
95
ProCarManuals.com

Page 96 of 498

Programmable Unlocking Feature
The following is the list of available programming
options:
Mode 1:Driver’s door unlocks when the
transmission is shifted into PARK (P).
Mode 2:All doors unlock when the transmission
is shifted into PARK (P).
Mode 3:All doors unlock when the key is
removed from the ignition.
Mode 4:No automatic door unlock.
The automatic door locks were pre-programmed at
the factory to unlock all doors once the
transmission is shifted to PARK (P). The following
instructions detail how to program your door
locks differently than the factory setting. Choose
one of the four programming options listed
previously before entering the program mode.
To enter the program mode you need to do the
following:
1. Begin with the ignition off. Then pull the turn
signal/multifunction lever toward you and hold
it there while you perform the next step.2. Turn the key to RUN and LOCK twice. Then,
with the key in LOCK, release the turn
signal/multifunction lever. Once you do this,
you will hear the lock switch lock and
unlock, the horn will chirp twice, and a
30-second program timer will begin.
3. You are now ready to program the automatic
door locks. Select one of the four programming
options listed above, and press the unlock side
of the power door lock switch to cycle through
the unlocking options. You will have
30 seconds to begin programming. If you
exceed the 30-second limit, the locks will
automatically lock and unlock and the horn will
chirp twice to indicate that you have left the
program mode. If this occurs, repeat the
procedure beginning with Step 1 to re-enter the
programming mode.
You can exit the program mode any time by turning
the ignition to RUN. The locks will automatically
lock and unlock and the horn will chirp twice to
indicate that you are leaving the program mode.
If the lock/unlock switches are not pressed while in
the programming mode, the current auto lock/
unlock setting will not be modied.
See your dealer for more information.
96
ProCarManuals.com

Page 97 of 498

Rear Door Security Locks
Your vehicle may have this feature. You can lock
the rear doors so they cannot be opened from
the inside by passengers. To use one of
these locks do the following:
1. Open one of the rear doors. You will nd a
security lock lever located on the inside
edge of each rear door.
2. Move the lever
down to engage
the security
lock. Move the lever
up to disengage
the security lock.
3. Close the door.The rear doors of your vehicle cannot be opened
from the inside while this feature is in use. If
you want to open the rear door while the security
lock is on, unlock the door and open the door
from the outside.
Lockout Protection
This feature stops the power door locks from
locking when the key is in the ignition and a door
is open to protect you from locking your key in
the vehicle.
If the power lock switch is pressed when a door is
open and the key is in the ignition, all the doors
will lock and then the driver’s door will unlock.
97
ProCarManuals.com

Page 100 of 498

Power Windows
The controls for the power windows are located on
the armrest on each of the side doors. With power
windows, the switches operate the windows when
the ignition is in RUN, ACC or when Retained
Accessory Power (RAP) is active. SeeRetained
Accessory Power (RAP) on page 108. The driver’s
door also has a switch for each of the passenger’s
windows.Press down the top of the switch to lower the
window and pull up on the switch to raise
the window. If you hold the switch down for
three to seven seconds after the window has been
completely lowered or raised, the window will
not operate for about 15 seconds.
Express-Down Window
AUTO (Express-down):The driver’s and front
passenger’s window switches have an
express-down feature that allows you to lower the
window without holding the switch down. Press
down briey on the driver’s or front passenger’s
window switch labeled AUTO to activate the
express-down feature. Lightly tap the switch to
open the window slightly. The express-down
feature can be interrupted at any time by pressing
the top of the switch.
100
ProCarManuals.com

Page 102 of 498

Content Theft-Deterrent
Your vehicle is equipped
with a content
theft-deterrent alarm
system.
Here is how to operate the system:
1. Open the door.
2. Lock the door with the power door lock switch
or the remote keyless entry transmitter. The
security light should ash.
3. Close all doors. The security light should turn
off after approximately 30 seconds. The alarm
is not armed until the security light turns off.
If a locked door is opened without the key or the
remote keyless entry transmitter, the alarm will go
off. The headlamps and parking lamps will ash
for two minutes, and the horn will sound for
30 seconds, then will turn off to save the
battery power.Remember, the theft-deterrent system will not
activate if you lock the doors with a key or use the
manual door lock. It activates only if you use a
power door lock switch with the door open, or with
the remote keyless entry transmitter. You should
also remember that you can start your vehicle with
the correct ignition key if the alarm has been set off.
Here is how to avoid setting off the alarm by
accident:
If you do not want to activate the
theft-deterrent system, the vehicle should be
locked with the door keyafterthe doors
are closed.
Always unlock a door with a key, or use the
remote keyless entry transmitter. Unlocking
a door any other way will set off the alarm.
If you set off the alarm by accident, unlock any
door with the key. You can also turn off the alarm
by pressing unlock on the remote keyless entry
transmitter. The alarm will not stop if you try
to unlock a door any other way.
102
ProCarManuals.com

Page 104 of 498

PASS-Key®III Operation
Your vehicle is equipped
with the PASS-Key®III
(Personalized
Automotive Security
System) theft-deterrent
system. PASS-Key
®III
is a passive
theft-deterrent system.
This means you do not have to do anything different
to arm or disarm the system. It works when you
insert or remove the key from the ignition.When the PASS-Key
®III system senses that
someone is using the wrong key, it shuts down the
vehicle’s starter and fuel systems. The starter will
not work and fuel will stop being delivered to the
engine. Anyone using a trial-and-error method to
start the vehicle will be discouraged because of the
high number of electrical key codes.
When trying to start the vehicle, if the engine does
not start and the SECURITY light comes on, the
key may have a damaged transponder. Turn
the ignition off and try again.
If the engine still does not start, and the key
appears to be undamaged, try another ignition key.
At this time, you may also want to check the fuse.
SeeFuses and Circuit Breakers on page 435.Ifthe
engine still does not start with the other key, your
vehicle needs service. If your vehicle does start, the
rst key may be faulty. See your dealer who can
service the PASS-Key
®III to have a new key made.
104
ProCarManuals.com

Page 105 of 498

It is possible for the PASS-Key®III decoder to
learn the transponder value of a new or
replacement key. Up to 10 keys may be
programmed for the vehicle. This procedure
is for programming additional keys only.
Canadian Owners:If you lose or damage your
keys, only a GM dealer can service PASS-Key
®III
to have new keys made. To program additional
keys you will require two current driver’s keys. You
must add a step to the following procedure.
After Step 2 repeat Steps 1 and 2 with the second
current driver’s key. Then continue with Step 3.
To program the new key, do the following:
1. Verify that the new key has PK3 stamped on it.
2. Insert the current driver’s key in the ignition
and start the engine. If the engine will not
start, see your dealer for service.
3. After the engine has started, turn the key to
LOCK, and remove the key.4. Insert the key to be programmed and turn it to
ON within 10 seconds of removing the
previous key.
5. The SECURITY light will turn off once the key
has been programmed. It may not be apparent
that the SECURITY light went on due to
how quickly the key is programmed.
6. Repeat Steps 1 through 4 if additional keys
are to be programmed.
If you are ever driving and the SECURITY light
comes on and stays on, you will be able to restart
your engine if you turn it off. Your PASS-Key
®III
system, however, is not working properly and must
be serviced by your dealer. Your vehicle is not
protected by the PASS-Key
®III system at this time.
If you lose or damage a PASS-Key
®III key, see
your dealer to have a new key made.
105
ProCarManuals.com

Page 107 of 498

Ignition Positions
Use the key to turn
the ignition switch to
four different positions.
The ignition switch
is located on the
center console.
9(LOCK):This position locks the ignition and
transmission. It is a theft-deterrent feature. You will
only be able to remove the key when the ignition
is turned to LOCK and the vehicle has power.
Notice:Using a tool to force the key from the
ignition switch could cause damage or break
the key. Use the correct key and turn the key
only with your hand. Make sure the key is all the
way in. If it is, turn the steering wheel left and
right while you turn the key hard. If none of this
works, then your vehicle needs service.ACC (Accessory):This position lets you use
things like the radio and the windshield wipers
when the engine is off.
Lengthy operation of features such as the radio in
the accessory ignition position may drain the
battery and prevent your vehicle from starting. Do
not operate your vehicle in the accessory
ignition position for a long period of time.
R(RUN):This is the position for driving.
The battery could be drained if you leave the key
in the ACC or RUN position with the engine
off. You may not be able to start your vehicle if
the battery is allowed to drain for an extended
period of time.
/(START):This position starts the engine.
107
ProCarManuals.com

Page 108 of 498

Key In the Ignition
Never leave your vehicle with the keys inside, as it
is an easy target for joy riders or thieves. If you
leave the key in the ignition and park your vehicle,
a chime will sound, when you open the driver’s
door. Always remember to remove your key from
the ignition and take it with you. This will lock
your ignition and transaxle. Also, always remember
to lock the doors.
The battery could be drained if you leave the key
in the ignition while your vehicle is parked.
You may not be able to start your vehicle after it
has been parked for an extended period of time.
Retained Accessory Power (RAP)
Your vehicle is equipped with a Retained Accessory
Power (RAP) feature which will allow certain
features of your vehicle to continue to work up to
10 minutes after the ignition key is turned to LOCK.
Your radio, power windows, DVD player, sunroof
(option) and overhead console will work when
the ignition key is in RUN or ACC. Once the key is
turned from RUN to LOCK, these features will
continue to work for up to 10 minutes or until
a door is opened.
Starting the Engine
Place the transmission in the proper gear.
Move your shift lever to PARK (P) or
NEUTRAL (N). Your engine will not start in
any other position -- this is a safety feature.
To restart when you are already moving, use
NEUTRAL (N) only.
Notice:Do not try to shift to PARK (P) if your
vehicle is moving. If you do, you could
damage the transmission. Shift to PARK (P)
only when your vehicle is stopped.
Starting Procedure
1. With your foot off the accelerator pedal, turn
the ignition key to START. When the engine
starts, let go of the key. The idle speed will go
down as your engine gets warm. Do not
race the engine immediately after starting it.
Operate the engine and transmission gently to
allow the oil to warm up and lubricate all
moving parts.
108
ProCarManuals.com

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 ... 90 next >