Seat Ibiza ST 2014 Owner's manual

Fuses and bulbs
– Unclip the retainer spring ››› Fig. 177 3 pressing inwards to the right.
– Extract the bulb and fit the replacement so
that the lug on the base fits into the recess
on the reflector.
– Fit the connector.
– Fit the cover and close the strap. Make sure
that the gasket sits well on the casing cover
during the operation.
– Check whether the new bulb is working.
Side light Fig. 178
Side lights. –
Raise the bonnet.
– Move the loop ››› Fig. 176 1 in the direc-
tion of the arrow and remove the cover.
– Remove the bulb holder 4
››› Fig. 178 out-
w ar
ds. –
Replace the bulb by pulling it out and in-
serting the replacement.
– Installation is done in the reverse order.
Double headlight bulb change Double headlight bulbs Fig. 179
Double headlight. Side lights
Main beam headlights
Dipped beam headlights
Turn signal lights
A B
C
D Side light
Fig. 180
Side lights. Fig. 181
Side lights. –
Raise the bonnet.
– Move the loop 1 in the direction of the ar-
row and remove the cover ››› Fig. 180 .
– Remo

ve connector ››› Fig. 181 2 by pulling
outward. »
199
Technical specifications
Advice
Operation
Safety
The essentials

Advice
– Remove the bulb by pulling it out and fit-
ting the new one.
– Installation involves all of the above steps
in reverse sequence.
– Fit the cover and close the strap. Make sure
that the gasket sits well on the casing cover
during the operation.
– Check whether the new bulb is working.
Main beam headlight Fig. 182
Main beam headlight. Fig. 183
Main beam headlight. –
Raise the bonnet.
– Move the loop 1 in the direction of the ar-
row and remove the cover ››› Fig. 182 .
– Remo
ve connector ››› Fig. 183 2 by pulling
outward.
– Extract the bulb and fit the replacement so
that it sits correctly into the cut-out on the
reflector.
– Installation involves all of the above steps
in reverse sequence.
– Fit the cover and close the strap. Make sure
that the gasket sits well on the casing cover
during the operation.
– Check whether the new bulb is working. Dipped beam headlight
Fig. 184
Dipped beam headlights. Fig. 185
Dipped beam headlights. –
Raise the bonnet.
– Move the loop ››› Fig. 184 1 in the direc-
tion of the arrow and remove the cover.
– Remove connector ››› Fig. 185 2 from the
bulb.
200

Fuses and bulbs
– Unclip the retainer spring ››› Fig. 185 3 pressing inwards to the right.
– Extract the bulb and fit the replacement so
that the lug on the base fits into the recess
on the reflector.
– Fit the connector.
– Fit the cover and close the strap. Make sure
that the gasket sits well on the casing cover
during the operation.
– Check whether the new bulb is working.
Turn signal lamp Fig. 186
Turn signal light. –
Raise the bonnet.
– Turn bulb holder ››› Fig. 186 A to the left
and pull. –
Remove the bulb by pressing on the bulb
holder and turning it anti-clockwise at the
same time.
– Installation involves all of the above steps
in reverse sequence.
AFS headlight bulb change AFS headlight bulbs Fig. 187
AFS headlight bulbs. Turn signal lights
Xenon headlight (dipped beam/main
beam)
Changing the xenon bulb The procedure for changing the bulb is the
same on both sides of the vehicle.A B WARNING
This type of bulb should be changed at a spe-
cialised workshop. Turn signal bulb
Fig. 188
Turn signal light. –
Raise the bonnet.
– Turn bulb holder ››› Fig. 188 A to the left
and pull.
– Remove the bulb by pressing on the bulb
holder and turning it anti-clockwise at the
same time.
– Installation involves all of the above steps
in reverse sequence.
201Technical specifications
Advice
Operation
Safety
The essentials

Advice
Changing the fog light bulbs Front fog light bulb Fig. 189
Front fog light. Fig. 190
Front fog light. –
Remove the bolt ››› Fig. 189 1 from the fog
light grille with a screwdriver.
– Subsequently, remove the clips located on
the edge of the grill with gentle leverage. –
Remove the 3 bolts ››› Fig. 190 2 to re-
move the fog light.
– Remove the metal clip situated on the up-
per part of the fog light by pulling towards
the exterior of the vehicle ››› Fig. 190 3 .
Fog light, FR version Fig. 191
Fog light: access to the connector
and to the light bulb holder. –
Remove the 4 bolts A
››› Fig. 191 from the
in s
ide of the wheel housing and the 2 bot-
tom bolts B
››› Fig. 191 from the bumper
with a screwdriver.
– Pull the bumper to release it from its an-
chorages to access the connector and the
light bulb holder. Note
Due to the difficulty of accessing fog light
bulbs, have them replaced at a Technical
Service or specialised workshop. Remove the bulb holder
Fig. 192
Front fog light. –
Remove connector ››› Fig. 192 1 from the
bulb.
– Turn the bulb holder ››› Fig. 192 2 to the
left and pull.
– Remove the bulb by pressing on the bulb
holder and turning it counter-clockwise at
the same time.
– Installation involves all of the above steps
in reverse sequence.
– Check that the bulb works properly.
202

Fuses and bulbs
Changing the rear bulbs Summary of LED tail lights 3 Applies to the model: IBIZA/IBIZA SC
LED
●
Br ak
e lights
● Side lights
Bulbs
● Retro fog light
● Reverse lights
● Turn signal
Tail lights 3 Applies to the model: IBIZA SC
Fig. 193
Left tail light. Fig. 194
Right tail light. Turn signals
Side and brake
Position
Retro-fog light (left tail light)
Reverse light (right tail light)
Note
In countries driving on the right (left-driving),
both the D and
E bulbs are located the oth-
er way round (Retro-fog light on driver side
and reverse light on passenger side). A
B
C
D
E Access to tail lights
3 Applies to the model: IBIZA/IBIZA SC
Fig. 195
Access to tail lights. –
Open the rear lid.
– Turn the bolt in the direction of the arrow,
by hand or with a screwdriver ››› Fig. 195 .
– Remo

ve the tail light, by pulling it out-
wards.
203
Technical specifications
Advice
Operation
Safety
The essentials

Advice
Changing the tail light bulbs 3 Applies to the model: IBIZA/IBIZA SC
Fig. 196
Changing the tail light bulbs Fig. 197
Changing the tail light bulbs –
Remove the connector from housing A›››
Fig. 195 . –
Remo ve the bulb holder, separating it from
the casing. To do this, press tabs B in the
direction of the arrows ››› Fig. 196 .
– When the b u

lb holder has been removed,
press in the direction of the arrow 1 and
at the same time, turn in the direction of
the arrow 2
››› Fig. 197
Changing bulbs. LED lamps
Carry out the same operations as in lights fit-
ted with bulbs.
If necessary, remove the socket, as if it were
a bulb.
If the brake light and/or side light with LEDs
have to be replaced, the tail light must be re-
placed.
Changing the tail light bulbs
(on the side panel)
Overview of tail lights 3 Applies to the model: IBIZA ST
Tail lights on side panel Bulb lamps ● Brake lights
● Side lights
● Turn signal Tail lights on side panel LED lamps
●
Brake light (LED)
● Side light (LED)
● Turn signal
Accessing the side light bulbs 3 Applies to the model: IBIZA ST
Fig. 198
Lights on the side. –
Open the rear lid.
– Look for a lid with a grill behind the side
lights.
– Remove the lid with a flat screwdriver, plac-
ing it in notch A
››› Fig. 198 .
204

Fuses and bulbs
Changing bulbs 3 Applies to the model: IBIZA ST
Fig. 199
Removing the bulb holder. –
Remove the bulb holder by pressing the
fastening clip B
››› Fig. 199 and pulling it
outw ar
ds.
– Replace the faulty bulb, rotating it to the
left and outwards.
– To refit follow the steps in reverse order,
taking special care when fitting the bulb
holder.
Changing bulbs. LED lamps
Carry out the same operations as in lights fit-
ted with bulbs.
If necessary, remove the socket, as if it were
a bulb.
If the brake light and/or side light with LEDs
have to be replaced, the tail light must be re-
placed. Changing the tail light bulbs
(on the rear lid)
Overview of tail lights 3 Applies to the model: IBIZA ST
Light s

on the rear lid Bulb lamps
● Reverse lights
● Side lights
● Fog lights
Lights on the rear lid LED lamps
● Reverse lights
● Side light (LED)
● Fog lights
Accessing the rear lid lights 3 Applies to the model: IBIZA ST
Fig. 200
Lights on the boot. –
Open the rear lid.
– On the rear lid lining there is a lid behind
each light.
– Remove the lid with a flat screwdriver, plac-
ing it in notch A
››› Fig. 200 .
Ch an
ging bulbs 3 Applies to the model: IBIZA ST
Fig. 201
Removing the bulb holder. –
Remove the bulb holder by pressing the
fastening clips B
››› Fig. 201 and pulling
outw ar

ds.
– Replace the faulty bulb, rotating it to the
left and outwards.
– To refit follow the steps in reverse order,
taking special care when fitting the bulb
holder.
»
205
Technical specifications
Advice
Operation
Safety
The essentials

Advice
Changing bulbs. LED lamps
Carry out the same operations as in lights fit-
ted with bulbs.
If necessary, remove the socket, as if it were
a bulb.
If the brake light and/or side light with LEDs
have to be replaced, the tail light must be re-
placed.
Changing the side and interior
bulbs
Turn signals Fig. 202
Turn signals. –
Press the turn signal to the left or to the
right to remove the bulb.
– Remove the bulb holder from the turn sig-
nal. –
Remove the failed bulb and replace with a
new bulb.
– Insert the bulb holder in the turn signal
guide until it clicks into place.
– First fit the turn signal in the opening in the
chassis, fastening the tabs 1
››› Fig. 202 ,
and then fit in the b
ulb as shown by the ar-
row 2
››› Fig. 202 .
Number p l

ate light 3 Applies to the model: IBIZA/IBIZA SC
– Insert the flat part of a screwdriver into the
special slot and remove the bulb.
– Remove the bulb holder, by turning it until
it is free.
– Change the bulb.
– Replace the bulb holder, by turning it until
it fits fully.
– Fit the light into the space and press until
you hear a “click”. Number plate light 3 Applies to the model: IBIZA ST
Fig. 203
Remove the number plate light. –
Insert the flat part of a screwdriver into the
special slot and remove the number plate
light from its moulding.
– Remove the connector and extract the bulb.
After changing the bulb, fit the connector
again.
– Place the light in its moulding, pressing the
left side. Once it is fitted into place, press
the right side until you hear a click.
206

Fuses and bulbs
Interior light and front reading lights Fig. 204
Front reading light. To remove the glass
– Insert a fine screwdriver between the cas-
ing and the glass ››› Fig. 204 .
– Car
efully remove the glass, levering it to
avoid possible damage.
To replace the bulbs
– Pull the bulbs outwards.
– To remove the central bulb, hold and press
to one side.
Assembly
– Proceed in the reverse order, pressing gen-
tly on the outer edge of the side light.
– First fit the glass with the fastening tabs
over the frame of the switch. Next press the front part until the two long tabs click on
the support.
Additional brake light* Given the difficulty involved in the replace-
ment of this light it should be done by Tech-
nical Services.
Luggage compartment light* Fig. 205
Boot light. Fig. 206
Boot light. –
Remove the tulip-shaped fitting by pressing
on its inside edge (arrow) using the flat
side of a screwdriver ››› Fig. 205 .
– Pr e

ss the bulb sideways and remove it from
its housing ››› Fig. 206.
207
Technical specifications
Advice
Operation
Safety
The essentials

Technical specifications
Technical specifications
Technical features
Important information Important The information in the vehicle documentation
always takes precedence over the informa-
tion in this Instruction Manual.
All technical specifications provided in this
documentation are valid for the standard
model in Spain. The vehicle data card inclu-
ded in the Maintenance Programme or the
vehicle registration documents shows which
engine is installed in the vehicle.
The figures may be different depending
whether additional equipment is fitted, for
different models, for special vehicles and for
other countries.
Abbreviations used in the technical
specifications sectionAbbrevia-
tionMeaning
kWKilowatt, engine power measurement.
PSPferdestärke (horsepower), formerly used
to denote engine power.
rpmRevolutions per minute - engine speed.
NmNewton metres, unit of engine torque.
litres per100 kmFuel consumption in litres per 100 km (70
miles).
g/kmCarbon dioxide emissions in grams per
km (mile) travelled.
CO 2Carbon dioxide
CNCetane number, indication of the diesel
combustion power.
RONResearch octane number, indication of
the knock resistance of petrol. Vehicle identification data
Fig. 207
Vehicle data sticker (boot). Fig. 208
Chassis number.208