Seat Ibiza ST 2016 Owner's Guide

The essentialsIllustra-
tionKey to ››› Fig. 40
A  Do not continue driving!
The bonnet is open or is not properly
closed ››› page 201.
B  Do not continue driving!
The rear lid is open or is not properly
closed ››› page 9.
C, D  Do not continue driving!
A vehicle door is open or is not properly
closed ››› page 107. Warning and information messages
The system runs a check on certain compo-
nents
and f
unction

s when the ignition is
switched on and while the vehicle is moving.
Faults in the operation are displayed on the
screen using red and yellow symbols and
messages on the instrument panel display
( ›››
 page 100,
››› page 35) and, in
some cases, with audible warnings. The dis-
play may vary according to the type of instru-
ment panel fitted.
Priority 1 warning (red symbols)
Symbol flashing or lit; partly combined with audible
warnings.
 Stop the vehicle! It is dangerous ››› in Warning
symbols on page 101!
Check the function that is faulty and repair it. If necessa-
ry, request assistance from specialised personnel.
Priority 2 warning (yellow symbols)
Symbol flashing or lit; partly combined with audible
warnings.
A faulty function, or fluids which are below the correct
levels may cause damage to the vehicle! ›››
in Warn-
ing symbols on page 101
Check the faulty function as soon as possible. If neces-
sary, request assistance from specialised personnel.
Informative text
Information relating to different vehicle processes. Assist systems submenu
Assist
systems
menuFunction
Fatigue
detection *Switching the fatigue detection on or
off (pause recommendation)
››› page 174. Journey data
M emor y The MFD (multifunction display) shows differ-
ent

v alue

s for the journey and the consump-
tion. Changing between display modes on the
MFD
● In vehicles without multifunction steering
wheel: Pr
ess the rocker switch  on the
w ind
sc
reen wiper lever ››› Fig. 37.
● Vehicles with a multifunction steering
wheel: t
urn the thumbwheel ››› Fig. 38.
Multifunction display memory
The multifunction display is equipped with
three memories that work automatically: MFD
from departure, MFD from refuelling and MFD
total calculation. On the screen display, you
can read which memory is currently dis-
played.
Toggle between memories with the ignition
on and the memory displayed
Press the  button on the windscreen
w iper l
ever or the  button of the multifunc-
tion s t
eerin g wheel

. » 29

The essentialsMenuFunction
MFD from
departure
Display and storage of the values for
the journey and the consumption from
when the ignition is switched on to
when it is switched off.
If the journey is continued in less than
2 hours after the ignition is switched
off, the new data is added to the data
already stored in the memory. The
memory will automatically be deleted if
the journey is interrupted for more than
2 hours.
MFD from refuellingDisplay and storage of the values for
the journey and the consumption. By
refuelling, the memory will be erased
automatically.
MFD total
calcula-
tion
The memory records the values for a
specific number of partial trips, up to a
total of 19 hours and 59 minutes or 99
hours and 59 minutes, or 1999.9 km or
9999 km, depending on the model of
instrument panel. On reaching either of
these limits a)
, the memory is automati-
cally erased and starts to count from 0
again.
a) It varies according to the instrument panel version.
Erasing a memory manually
● Select the memory that you wish to erase.
● Hold the  button of the multifunction
s t
eerin g wheel

or the  button of the multi-
f u nction wheel
pr
essed down for about 2 sec-
onds. Personalising the displays
In the Easy C

onnect system you can adjust
which of the possible displays of the MFD can
be shown on the instrument panel display
with the button  and the function button
Set up
› ››
 p
age 101.
Dat a s

ummary
MenuFunction
Current fuel
consumption
The current fuel consumption dis-
play operates throughout the jour-
ney, in litres/100 km; and with the
engine running and the vehicle
stopped, in litres/hour.
Average fuelconsumption
After turning on the ignition, aver-
age fuel consumption in li-
tres/100 km will be displayed after
travelling about 100 metres. Other-
wise horizontal lines are displayed.
The value shown is updated approxi-
mately every 5 seconds.
ACT ®
*: Depending on the equip-
ment, number of active cylinders.
Operating range
Approximate distance in km that can
still be travelled with the fuel re-
maining in the tank, assuming the
same style of driving is maintained.
This is calculated using the current
fuel consumption.
MenuFunction
TravellingtimeThis indicates the hours (h) and mi-
nutes (min) since the ignition was
switched on.
Distance
coveredDistance covered in km (m) after
switching on the ignition.
Average
speed
The average speed will be shown af-
ter a distance of about 100 metres
has been travelled. Otherwise hori-
zontal lines are displayed. The value
shown is updated approximately ev-
ery 5 seconds.
Digital dis- play of
speedCurrent speed displayed in digital
format.
Speed warn-
ing at ---
km/h or Speed
warning at
--- mphIf the stored speed is exceeded (be-
tween 30 - 250 km/h, or 19 -
155 mph), an audible warning is
given together with a visual warn-
ing.
Oil tempera-
tureUpdated engine oil temperature dig-
ital display
Coolant tem-
perature
gaugeDigital display of the current temper-
ature of the liquid coolant. Storing a speed with the speed warning
● Select the display Speed warning at
--- km/h (---
mph) 30

The essentials
● Pr e
ss
the button  on the windscreen
w iper l
ever or the b
utton  on the multifunc-
tion s t
eerin g wheel
to store the current speed
and activate the warning.
● To switch system on: adjust to the desired
speed within 5 second
s using the rocker
switch  on the windscreen wiper lever or
b y
t urnin

g the thumbwheel on the multifunc-
tion steering wheel. Next, press the button  or
 again or wait several seconds.
The s peed i
s s

tored and the warning activa-
ted.
● To switch system off: press the but-
ton  or
 . The stored speed is de-
l et
ed.
En gine oi

l temperature display The engine reaches its operating temperature
when in norm
al
driv in

g conditions, the oil
temperature is between 80 °C (180 °F)
and 120 °C (250 °F) . If the engine is re-
quired to work hard and the outside tempera-
ture is high, the engine oil temperature can
increase. This does not present any problem
as long as the warning lamps  ›››
table on
page 36 or  ›››
table on page 36 do not
appear on the display. Vehicles without multifunction steering
wheel
●
Press the rocker switch ››› Fig. 37
2 until
the m ain menu ap
pear
s. Enter into Driving
data . With the button 2 move to the oil
t emper
atur

e gauge.
Vehicles with multifunction steering wheel
● Enter the submenu Driving data and
turn the thumbwheel u
ntil the oil tempera-
ture display appears.
Additional electrical appliances ●
Operation with the windscreen wiper lever*:
Pr e
ss

the rocker switch ››› Fig. 37 2 until the
m ain menu ap
pear
s. Enter into the section
Driving data . With the rocker switch,
move to the display Convenience con-
sumers .
● Operation with the multi-function steering
wheel*: Mo
ve with the buttons 1 or
2 to
Driving data and enter w
ith OK
.
Turn the
thumbwheel to the right until the Conven-
ience consumers display appears.
In addition, a scale will inform you of the cur-
rent sum of all the additional appliances. Saving tips Tips on how to save fuel will be displayed in
conditions
th

at increase fuel consumption.
Follow them to reduce consumption. The indi-
cations appear automatically only with the ef-
ficiency programme. After a time, the tips will
disappear automatically.
If you wish to hide a saving tip immediately
after it appears, press any button on the
windscreen wiper lever*/multifunction steer-
ing wheel*. Note
● If y ou hide a s

aving tip, it will reappear af-
ter you switch the ignition on again.
● The saving tips do not appear in all situa-
tions, but r
ather with a large separation of
time. Timer*
You can access the timer via the selection
menu
››
›
p

age 27.
It allows you to manually time lap times on a
racing circuit, memorise them and compare
them to the vehicle's previous best times.
The following menus can be displayed:
● Stop
● Lap » 31

The essentials
● Pause
● Partial time
● Statistics
Ch an
ge fr
om one menu to another
● Vehicles without multifunction steering
wheel: pr
ess the rocker switch  in the
w ind
sc
reen wiper lever.
● Vehicles with multifunction steering wheel:
press
 or
 .
Menu “Stop”
Start
The timer starts.
If there are existing laps and they are in-
cluded in the statistics, it will begin with
the number of laps in question.
It is only possible to begin with a new first
lap if the statistics have been reset first in
the Statistics
menu.
Since
startThe timer begins when the vehicle sets
off.
If the vehicle is already moving, the timer
begins once the vehicle has stopped.
Statis-
ticsThe Statistics menu is displayed on
the screen.
Menu “Lap”
New lap
The timer of the current lap stops and a
new lap starts immediately. The time for
the lap you have just completed is inclu-
ded in the statistics.
Menu “Lap”
Partial
timeFor about 5 seconds a partial time is dis-
played. The timer continues in parallel.
StopThe current lap timer will be interrupted.
The lap does not end. The Pause menu is
displayed.
Menu “Pause”
ContinueThe interrupted timer continues.
New lapA new timer starts. The halted lap ends
and is included in the statistics.
Interr. lapThe timer of the current lap ends and is
cancelled. It is not included in the statis-
tics.
EndThe current timer ends. The lap is inclu-
ded in the statistics.
Menu “Partial time”
Partial
timeFor about 5 seconds a partial time is dis-
played. The timer continues in parallel.
New lap
The timer of the current lap stops and a
new lap starts immediately. The time for
the lap you have just completed is inclu-
ded in the statistics.
StopThe current lap timer will be interrupted.
The lap does not end. The Pause menu is
displayed.
Menu “Long-term statistics”

View of the latest lap times:
– total time
– best lap time
– worst lap time
– average lap duration
A maximum of 10 laps is possible, and a
total duration of 99 hours, 59 minutes
and 59 seconds.
If one of the 2 limits is reached, you will
have to reset the statistics in order to be-
gin a new timer.
BackThis returns to the previous menu.
Reset-
ting to
zeroAll the memorised statistical data are re-
set. WARNING
Do your best to avoid handling the timer
while driv in

g.
● Only set the timer or consult statistics
when the vehicl
e is stationary.
● While driving, do not handle the timer in
complicat
ed driving situations. Speed warning device
The speed warning device warns the driver
when they
h
av e e

xceeded the pre-set speed
limit by 3 km/h. An audible warning is given
and the lamp  can be seen simultaneously 32

The essentials
on the instrument panel, as well as a mes-
s ag
e for the driv
er: speed warning ex-
ceeded! The warning lamp  switches off
when reducing speed below the stored maxi-
mum limit.
Speed warning programming is recommen-
ded if you wish to be reminded of a maxi-
mum speed, such as when travelling in a
country with different speed limits or for a
maximum speed for winter tyres.
Setting speed limit warning
You can use the radio or the Easy Connect* to
set, alter or cancel the speed limit warning.
● Vehicles with radio : press
the button SETUP> control button  Driver Assistant
>
Speed warning .
● Vehicles with Easy Connect : pre
ss

the but-
ton Systems or else Vehicle systems >
Driver assistant > Speed warning.
The warning limit can be set from 30 to
240 km/h (20 to 150 mph). The adjustment
is done in 10 km/h intervals. Note
● Plea se be

ar in mind that, even with the
speed warning function, it is still important
to keep an eye on the vehicle speed with the
speedometer and to observe the legal speed
limits. ●
The speed limit w arnin

g function in the ver-
sion for several countries warns you at a
speed of 120 km/h (80 mph). This is a facto-
ry-set speed limit. Service intervals
The service interval indication appears on the
instrument
p

anel display ›››
 Fig. 121
3 .
SEAT di s
tinguishes between services with en-
gine oil change (e.g. Oil change service) and
services without engine oil change (e.g. In-
spection).
In vehicles with Services established by time
or mileage, the service intervals are already
pre-defined.
In vehicles with LongLife Service , the inter-
vals are determined individually. Thanks to
technological progress, maintenance work
has been greatly reduced. Because of the
technology used by SEAT, with this service
you only need to change the oil when the ve-
hicle so requires. To calculate this change
(max. 2 years), the vehicle's conditions of
use and individual driving styles are consid-
ered. The advance warning first appears 20
days before the date established for the cor-
responding service. The kilometres (miles)
remaining until the next service are always
rounded up to the nearest 100 km (miles)
and the time is given in complete days. The
current service message cannot be viewed until 500 km after the last service. Prior to
this, only
line

s are visible on the display.
Inspection reminder
When the Service date is approaching, when
the ignition is switched on a Service remind-
er is displayed.
Vehicles without text messages : a span-
ner  will be displayed on the instrument
panel plus an indication in km.
The kilometres indicated are the maximum
number of kilometres that can be travelled
until the next service. After a few seconds,
the display mode changes. A clock symbol
appears and the number of days until the
next service is due.
Vehicles with text messages : Service in
--- km or --- days will be shown on the
instrument panel display.
Service due
When the service date is due , an audible
warning is given when the ignition is switch-
ed on and the spanner displayed on the
screen flashes for a few seconds .
Vehicles with text messages : Service now
will be shown on the instrument panel dis-
play. » 33

The essentials
Reading a service notification
W ith the ignition sw
itc
hed on, the engine off
and the vehicle at a standstill, the current
service notification can be read:
Press and hold the button 4 for more than 5
sec ond
s t

o consult the service message.
When the service date has passed , a minus
sign is displayed in front of the number of kil-
ometres or days.
Vehicles with text messages : the following
message is displayed: Service --- km
(miles) or --- days ago .
The time can also be set via the  key and
Set up function button in the Easy Connect
sy s
tem
›

››  page 101.
Resetting service interval display
If the service was not carried out by a SEAT
dealership, the display can be reset as fol-
lows: ● Switch off the ignition, press and hold but-
ton ›››

 Fig. 121
4 .
● Switch ignition back on.
● Release THE 4
› ›
›
 Fig. 121
b

utton and
press it again for the next 20 seconds. Note
● The servic e me

ssage disappears after a few
seconds, when the engine is started or when OK/RESET
is pressed on the windscreen wiper
lever , or OK on the multifunction steering
wheel.
● In v ehic

les with the LongLife system in
which the batter
y has been disconnected for
a long period of time, it is not possible to cal-
culate the date of the next service. Therefore
the service interval display may not be cor-
rect. In this case, bear in mind the maximum
service intervals permitted in the ››› Book-
let Maintenance Programme. Cruise control
Oper atin
g the c rui

se control system
(CCS)* Fig. 41
Turn signal and main beam headlight
l ev
er: sw it

ches and controls for operating the
CCS ●
Sw it
chin

g on the CCS: Move switch
››› Fig. 41 1 to .
The system is on. If no
s peed h a
s been programmed, the system will
not control it.
● Activating the CCS: Press button ››› Fig. 41
2 in the  ar
e
a. The c

urrent speed is
memorised and controlled.
● Temporarily switching off the CCS: Move
switch ›

›› Fig. 41 1 to 
 or push the
br ak e.
The cruise control system is switched
off temporarily.
● Reactivating the CCS: Press button
››› Fig. 41

2 in 

. The memorised speed
i s
saved and controlled again.
● Increasing stored speed during CCS regula-
tion: press
button 2 in 

. The vehicle ac-
c el
erates until the new stored speed.
● Reducing stored speed during CCS regula-
tion: press
button 2 in  t
o lower the
s peed b y
1 km/h (1 mph). Speed is reduced
until reaching the new stored speed.
● Switching off the CCS: Move switch
››› Fig. 41

1 to .
The system is disconnec-
t ed and the memori sed s
peed is deleted.

››› in Operation on page 183
››› page 183 34

The essentials
Warning lamps On the in s
trument p
anelFig. 42
Instrument panel, on dash panel Red warning lamps

Central warning lamp: additional
information on the instrument pan-
el display–

Parking brake on.›››
page
152
››› page
153  
Do not continue driving!
The brake fluid level is too low or
there is a fault in the brake system. 
Lit up or flashing: Do not continue driving!
Fault in the steering.››› page
148 
Driver or passenger has not fas-
tened seat belt.›››
page
62 
Use the foot brake! Yellow warning lamps

Central warning lamp: additional
information on the instrument pan-
el display–»
35

The essentials
Front brake pads worn.
›››
page
155 
it lights up:
Fault in the ESC, or dis-
connection caused by the system.
flashes: ESC or ASR activated. 
ASR manually deactivated.
Or else
: ESC in Sport mode. 
ABS faulty or does not work.

Front fog lights switched on.›››
page
21 
Rear fog light switched on.›››
page
21 
lights up or flashes:
fault in the
emission control system.››› page
171 
it lights up:
pre-heating of diesel
engine.
››› page
171
flashes: fault in the diesel engine
management. 
fault in the petrol engine manage-
ment.›››
page
171 
lights up or flashes:
fault in the
steering system.››› page
148 
Tyre pressure too low, or fault in
the tyre pressure monitoring sys-
tem.›››
page
216 
Fuel tank almost empty.›››
page
100 
Fault in airbag system and seat
belt tensioners.›››
page
66 Other warning lamps

Left or right turn signal.›››
page
22
Hazard warning lights on.››› page
123 
Trailer turn signals›››
page
186 
it lights up:
Press the foot brake!
flashes: the selector lever locking
button has not engaged.››› page
161 
it lights up:
cruise control activated
or speed limiter switched on and
active.
››› page
34
flashes: the speed set by the
speed limiter has been exceeded. 
Main beam on or flasher on.›››
page
22 On the instrument panel display
Fig. 43
On the instrument panel display: door
open.  
Do not continue driving!
With the corresponding indica-
tion: door(s), rear lid or bonnet
open or not properly closed.››› page
107
››› page 9
››› page
201 
Ignition:  Do not carry on driv-
ing! Engine coolant level too low,
coolant temperature too high
››› page
207
Flashing: Fault in the engine
coolant system.  
Do not continue driving!
Engine oil pressure too low.››› page
204 36

The essentials
Fault in the battery.›››
page
210 
Driving light totally or partially
faulty.›››
page
83
Fault in the cornering light sys-
tem.››› page
118 
Diesel particulate filter blocked›››
page
170 
Level of windscreen washer fluid
too low.›››
page
210 
Flashing: Fault in the oil level de-
tection. Control manually.›››
page
204
Ignition: Insufficient engine oil. 
Fault in the gearbox.›››
page
166 
Immobiliser active.›››
page
150 
Service interval display›››
page
33 
Mobile telephone is connected
via Bluetooth to the original tele-
phone device.›››
Book-
let Radio
or
››› Book-
let Navi-
gation
system 
Mobile telephone battery charge
meter. Available only for devices
pre-installed in factory.

Freezing warning. The outside
temperature is lower than +4 °C
(+39 °F).›››
page
27 
Start-Stop system activated.›››
page
172 
Start-Stop system unavailable.

Low consumption driving status›››
page
27 On the instrument panel
Fig. 44
Warning lamp for disabling the front
p a
ssen

ger airbag. 

Front passenger front airbag is
disabled (  
 ).
››› page
66 
››› in Warning symbols on page 101
›››
page 100 Gearbox lever
M anua
l g

earbox Fig. 45
Gear shift pattern of a 5 or 6-speed
m anual
ge

arbox The position of the gears is indicated on the
g
e
arbo x

lever ››› Fig. 45.
● Press the clutch pedal and keep your foot
right down.
● Mov

e the gearbox lever to the required po-
sition.
● Rele

ase the clutch.
Selecting rev
erse gear
● Press the clutch pedal and keep your foot
right down.
● With the g

earbox lever in neutral, push it
upward
s, move it to the left as far as it will go
and then forwards to select reverse ››› Fig. 45
R .
» 37

The essentials
● Rel
ea
se the clutch.

››› in Driving with manual gearbox on
page 161
››› page 161 Automatic gearbox*
Fig. 46
Automatic gearbox: selector lever po-
s ition
s. Parking lock
R
ev
erse g

ear
P
R Neutral (idling)
Drive (forw

ard)
Sport programme: drive (forward)
Tiptronic mode: pull the lever forwards
(+) to go up a gear or backwards ( –) to
go down a gear.

››› page 161
››› page 38 Manual release of selector lever
Fig. 47
Manual release of the selector lever. N
D
S
+/–
If there is a fault in the power system to the
el
ectr
onic sel

ector lever lock system (flat bat-
tery, blown fuse) or the system itself is faulty,
the selector lever cannot be moved from po-
sition P in the normal manner, which pre-
vents the vehicle from being moved. The se-
lector lever must be unlocked using the man-
ual release.
● Apply the handbrake.
● Pull gently on both sides at the front of the
selector lev
er cover.
● Also loosen the cover at the rear.
● Press the yellow plastic part with your fin-
ger in the direction indicat
ed by the arrow
››› Fig. 47.
● Press the interlock button on the selector
lever knob at
the same time and move the se-
lector lever to position N (if the selector lever
is moved back to position P, it will lock
again). 38