length Seat Leon 5D 2010 MEDIA SYSTEM 2.2

Audio mode21
RDS radio data and TP (Traffic Programme)
servicesIntroductionRDS (Radio Data System) is a radio data service for broadcasting programme
and additional service identifiers, and displaying station names and radio
text, automatic station tracking and traffic programmes.
The RDS is not compatible with all equipment and is not available everywhere
or on all radio stations.
Without RDS it is not possible to use the RDS radio services .
Additional Information:•Safety notes
’ ⇒ page 6
•Unit overview ⇒ page 8•Radio mode ⇒page 14Note
The radio station is responsible for the content of the broadcast
information.
RDS and radio textIf the RDS service is available and the quality of reception is good enough, the
station name may be displayed in Radio mode ⇒fig. 15 .
Automatic station tracking
Some FM stations broadcast different content (temporary or permanent) on
different wavelengths using the same name depending on the region.
By default, automatic station tracking always switches to the currently
selected radio station's frequency that offers the best reception, as the
vehicle travels from one area to the next. As a result, you may lose the
regional programme you are listening to. The automatic change of station can
be deleted using the setting menu Radio ⇒ page 19.
Display and delete the radio text
Some RDS-enabled stations also broadcast additional text information
known as radio text. It is possible to adjust the display to show radio text.•In the RADIO main menu, press the unit button.
Fig. 15 Main RADIO
menu with station name
display and TP function
activated.
º
MediaSystem2.1_EN.book Seite 21 Donnerstag, 29. April 2010 4:18 16

Navigation65
Visual recommendations on the mapWhen route guidance starts, the system automatically switches to the map
view ⇒fig. 65. The red
9 symbol indicates the vehicle's position and heading
⇒fig. 65 . If
the vehicle position symbol
9 remains in the same position and the map
view freezes, it is currently not possible to determine the vehicle's position,
e.g. in a multi-storey car park.
During route guidance the navigation route is shown as a blue line. Sections
closed to traffic either manually or due to TMC messages advising of traffic
congestion ⇒page 70 are shown in colour on the calculated route.
The next road to take is displayed in the top line of the screen.
After a few seconds, the function buttons disappear from the bottom line of
the screen to display more information on the route ⇒fig. 66.
•Briefly press the bottom-right or bottom-left area of the screen to display
the function buttons again ⇒ fig. 65.•Pressing the unit button switches between the Navigation main
menu and the map view.
When the function buttons are hidden, the current street and information
about the journey length are displayed on the bottom line of the screen
⇒ fig. 66 .: Remaining distance to the destination.: Expected time of arrival or travelling time ⇒page 73.
Shortly before you reach a turning point, a turning arrow appears, indicating
the direction to turn. The distance to the turning point is also displayed below
it.
Changing the map scale (Autozoom)
The “Autozoom” function is enabled for the map view by default. This means
that the map view automatically zooms in and out: Small scale on motorways.
Large scale in urban areas.•Turn the setting knob ⇒page 8, fig. 1 to manually change the scale
of the map for a few seconds. Turn the knob clockwise to zoom in. Turn the
knob anticlockwise to zoom out.
Fig. 65 Map view during
route guidance with the
function buttons
displayed.Fig. 66 Map view during
route guidance.
NAV
A10
MediaSystem2.1_EN.book Seite 65 Donnerstag, 29. April 2010 4:18 16

Navigation
70Directly excluding a route section further ahead (congestion)During a route guidance, the route section of the remaining stretch of route
can be excluded manually.•Press the unit button in any of the navigation menus (except SETUP).•In the information window , press the function button.•Press the function button in the pop-up window.•Enter the length of the section to be excluded by turning the setting knob
⇒ page 8, fig. 1 .
The length indicated for the route section is shown on the lower line of the
screen. If (Max) is displayed, this indicates that the maximum permitted
length for exclusion has been reached.•Press the setting knob or function key to confirm the exclusion.
The excluded route section is displayed on the map.
Route guidance will start again when the navigation system has calculated an
alternative route to the excluded section.
Re-opening a section•Press the unit button in any of the navigation menus (except SETUP).•In the information window , press the function button.•Press the function button in the pop-up window.Note
It is also possible to enter or cancel an exclusion while viewing the TMC traffic
announcements using the function button ⇒ page 71.
Note
Information on manually excluding route sections further ahead
⇒page 69.Dynamic route guidance with TMC (Traffic Message Channel)The prerequisite for dynamic route guidance is always the reception of a TMC
traffic news station for the navigation area available in the unit. TMC traffic
reports received can be displayed in a list ⇒page 71.
If dynamic route guidance is activated, any TMC traffic reports are taken into
account in the route calculation.
Switching the dynamic navigation on or off•Press the unit button in one of the navigation menus.•In the Navigation setup menu , press the function button to
open the Route options setup menu ⇒ fig. 71 .
º
Route
Congestion aheadA10OK
º
Route
Re-open section
Congestion ahead
Fig. 71 Route options
setup menu.
SETUP
Route options
MediaSystem2.1_EN.book Seite 70 Donnerstag, 29. April 2010 4:18 16

Telephone control (Phone)85
During a phone callActive connection display
During a phone call, the number of the caller and the length of the conversa-
tion are displayed on the screen.
If the phone number has been saved in the address book, the name allocated
to the number is displayed instead of the number.
Muting the call
To prevent the caller listening to conversations inside the car during an active
connection, the sound transfer to the other phone can be temporarily discon-
nected.•Press the button with a connection established.•Press the function button in the pop-up window to disconnect
sound transmission to the other caller.•Press the function button again in the pop-up window to restore
sound transmission to the other caller.
Accepting and holding an additional callAn additional call may be accepted during a telephone conversation. It is
possible to switch between calls.
Call notification: Accept additional incoming call•If you receive another call while you are talking on the phone, the phone
number or name of the caller is displayed on the screen. The display “ ...
calling ” is also shown•To reject the second caller, press the function button .•ALTERNATIVELY: Press the left unit button.•To accept the second call, press directly on the call notification, or the
function button .•ALTERNATIVELY: Press the right unit button.
If you accept the second call, the first caller is put on hold, but the connection
is not cut off (display: “ Hold call”).
Fig. 83 Display an active
connection.
ExtrasMuteMute
Fig. 84 Call notification.^

MediaSystem2.1_EN.book Seite 85 Donnerstag, 29. April 2010 4:18 16