ECU SKODA OCTAVIA 2010 2.G / (1Z) Owner's Guide

Page 195 of 275

Fuel
194Note
An extension cable used for connecting to the electrical network is located in the
luggage compartment.DieselDiesel fuelYour vehicle can only be operated with diesel fuel, which complies with the standard
EN 590 (standard DIN 51628 in Germany, standard ÖNORM C 1590 in Austria).
Fuel additives
You must not use fuel additives, so-called “flow improvers” (petrol and similar prod-
ucts) in diesel fuel.
You can find information on refuelling page 195, “Refuelling”.
Caution

Therefore, your vehicle can only be operated with diesel fuel which complies with
the standard EN 590 (standard DIN 51628 in Germany, standard ÖNORM C 1590 in
Austria). Filling the tank even only once wi th diesel fuel which does not comply with
the standard, can result in damage to the engine parts, the lubrication system, the fuel
and exhaust system.

If by mistake you have refuelled with a different fuel other than the diesel fuel
which complies to the above mentioned standards (e.g. petrol), do not start the engine
or switch on the ignition! This can result in severe engine damage! Contact a specialist
garage and have the fuel sy stem of the engine cleaned.

Water which has collected in the fuel fi lter can result in engine problems.

Your vehicle is not adapted for use of biofuel (RME), therefore this fuel must not be
refuelled and driven. The use of biofuel (RME) can lead to damage to the engine or the
fuel system.
Operation in winterWinter-grade diesel fuel
A different grade of diesel fuel is available at filling stations in winter than during the
summer. Using “summer-grade diesel fuel” at temperatures below 0°C can result in
operational problems because the diesel beco mes viscous as a result of paraffin sepa-
ration.
It is therefore the case that the standard EN 590 (standard DIN 51628 in Germany,
standard ÖNORM C 1590 in Austria) is the diesel fu el class prescribed for certain
periods of the year which can also be purc hased at the corresponding time during the
year. “Winter-grade diesel fuel” will still operate properly even at a temperature of -
20°C.
It is often the case in countri es with different climatic conditions that diesel fuels avail-
able have a different temperature characteristic. The authorised Škoda Service Part-
ners and filling stations in the country conc erned will be able to provide you with infor-
mation regarding the diesel fuels available.
Prewarming fuel
The vehicle is fitted with a fuel filter prewarming system. This secures operation of a
vehicle using diesel fuel down to an environmental temperature of -25°C.
Caution
It is not permitted to add the various fuel additives on the market, including petrol, to
diesel fuel in order to improve its flow properties.
s43s.1.book Page 194 Thursday, May 13, 2010 1:21 PM

Page 198 of 275

Inspecting and replenishing197
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Working in the engine compartment
Particular care is required when carrying out any work in the engine
compartment!There is a risk of injuries, scalding, acci dents and fire when working in the engine
compartment, e.g. inspecting and replenishing oil and other fluids. For this
reason, it is essential to comply with the warning instructions stated below and
with the general applicable rules of safe ty. The engine compartment of your car
is a hazardous area  .
WARNING

Never open the bonnet if you see that steam or coolant is flowing out of the
engine compartment - risk of scalding! Wait long enough until the steam or
coolant has stopped escaping.

Switch off the engine and pull out the ignition key.

Apply the handbrake firmly.

If your vehicle is fitted with a manual gearbox, move the gearshift lever into
Neutral, or if it is fitted with automatic gearbox, move the selector lever into
position P.

Allow the engine to cool down.

Keep children clear of the engine compartment.

Never spill oil and other fluids over the hot engine. Such fluids (e.g. the anti-
freeze contained in the coolant) may ignite!

Avoid short circuits in the electrical system - particularly on the battery.

Never place your hand into the radiator fan as long as the engine is still
warm. The fan might su ddenly start running!

Never open the cap of the coolant expans ion bottle as long as the engine is
still warm. The cooling system is pressurized!

Cover over the cap of the coolant expansion reservoir with a large cloth
when opening it as protection for your face, hands and arms from hot steam or
hot coolant.

Do not let objects, such as e.g cleaning cloth or tools lie in the engine
compartment.

If you wish to work under the vehicl e, you must secure the vehicle from
rolling away and support it with suitable supporting blocks; the lifting jack* is
not sufficient for this - risk of injury!

In cases where it be necessary to carry out inspection work when the engine
is running there is an additional risk fr om rotating parts (e.g. the V-ribbed belt,
alternator, radiator fan) and from the high-voltage ignition system. Please
observe in addition the following:
Never touch the electrical cabl es of the ignition system.
 Absolutely avoid any jewellery, loose it ems of clothing or long hair from
getting into the rotating parts of the engine - Hazard! Therefore remove any
jewellery beforehand, tie up your hair and wear tight fitting clothing.

Please also comply with the warnin g instructions stated below when
carrying out any essential work on the fu el system or on the electrical system:
 Always separate the car battery from the electrical system.
 Do not smoke.
 Never carry out any work close to naked flames.
 Always keep a working fire extinguisher at hand.Caution
When replenishing fluids in the engine, always ensure that the fluids are on no account
mixed up. This may result in major oper ating problems and also vehicle damage!
WARNING (continued)
s43s.1.book Page 197 Thursday, May 13, 2010 1:21 PM

Page 217 of 275

Breakdown assistance
216WARNING
If the fire extinguisher is not correctl y attached, in case of sudden manoeuvres
or an accident it can be “thrown” through the interior compartment and cause
injuries.
Note

The fire extinguisher must comply with the relevant and valid legal requirements.

Pay attention to the expiration date of the fire extinguisher. If the fire extinguisher
is used after the expiration date, its proper function is no longer assured.

The fire extinguisher is only supplied in certain countries within the scope of
delivery.
Vehicle tool kitThe vehicle tool kit and the lifting jack* are housed in a box in the spare wheel*
 fig. 174 or in the space for the spare wheel. There is also space here for the remov-
able ball for the trailer towing device*. Th e box is attached with a strap on the spare
wheel.
The vehicle tool kit contains the following parts (depending on equipment fitted):
Wire clamps for removing the full wheel trims,

Plastic clip for a wheel bolt cover,

Wheel wrench*,

To w i n g e y e ,

Adapter for the wheel bolts lock.*

Screwdriver* for removing the fog lights
18).
Before placing the lifting jack* back in its storage area, screw in the arm of the lifting
jack fully.
WARNING

The factory-supplied lifting jack* is only intended for your model of vehicle.
On no account attempt to lift a heavier vehicle or other loads - risk of injury!

Ensure that the vehicle tool kit is sa fely attached in the luggage compart-
ment.Note
Ensure that the box is always secured with the strap.Tyre repair kit*The tyre repair kit is intended for the repair of minor tyre defects. The tyre repair kit
contains a compressor, inflation bottle, operating instructions and accessories.
The repair with the tyre repair kit is not at all intended to replace a permanent repair
on the tyre, this repair only serves to reach the next specialist garage. The repair can be
undertaken on the vehicle immediately. Please read the attached instructions care-
fully before the repair.
The tyre repair kit is located in a textile bag. There is a velcro fastener on the underside
of the bag, with which the bag is attached to the floor covering of the luggage compart-
ment in such a way that the side of the bag rests on the right side of the luggage
compartment and on the seat backrest.
Fig. 174 Luggage compartment: storage
compartment for vehicle tool kit
18)Valid for Octavia RS and Octavia Scout.
s43s.1.book Page 216 Thursday, May 13, 2010 1:21 PM

Page 218 of 275

Breakdown assistance217
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Spare wheel*The spare wheel lies in a well under the floor covering of the luggage compartment and
is fixed in place using special screws fig. 175 .
Before removing the spare wheel, you must take out the box with the vehicle tool kit
box page 216, fig. 174.
One should check the inflation pressure in the spare wheel (at best when generally
checking the tyre air pressures - see sign on the fuel filler flap page 208) to ensure
that the spare wheel is always ready to use.
Temporary spare wheel
A warning label displayed on the rim of the temporary spare wheel indicates that your
vehicle is equippe d with a temporary spare wheel.
Please observe the following notes when driving with a temporary spare wheel:
The warning label must not be covered after installing the wheel.

Do not drive faster than 80 km/h with this spare wheel and pay particular attention
while driving. Avoid accelerating at full throttle, sharp braking and fast cornering.

The inflation pressure for this spare wheel is identical to the inflation pressure of
the standard tyres. The temporary spare wheel R 18 must have an inflation pressure of
420 kPa (4.2 bar)!

Use this spare wheel only to reach the nearest specialist garage as it is not intended
for continuous use.

No other summer or winter tyres must be mounted on the rim of the spare wheel
R 18.
Changing a wheelPreliminary workThe following steps should be carried ou t before actually changing the wheel.
– If it is necessary to change a wheel, park the vehicle as far away as possible from
the traffic flow. The place you choose should be level.
–Have all the occupants get out. While changing a wheel, the occupants of the
vehicle should not stand on the ro ad (e.g. behind a crash barrier).
– Apply the handbrake firmly.
–Engage 1st gear or if your vehicle is fitted with an automatic gearbox, position the
selector lever into position P .
– If a trailer is coupled, uncouple it.
–Take the vehicle tool kit  page 216 and the spare wheel*  page 217 out of the
luggage compartment.
WARNING

If you find yourself in flowing traffic switch on the hazard warning lights
system and place the warning triangle on the side of the road at the prescribed
distance from your vehicle while observin g all national legal provisions. In this
way you are protecting not only yourself but also other road users.

Never start the engine with the vehicle si tting on the raised jack - danger of
suffering injury.Caution
If you have to change a wheel on a slope fi rst block the opposite wheel with a stone or
similar object in order to secure the vehicle from unexpectedly rolling away.
Note
Comply with the national legal regulations.
Fig. 175 Luggage compartment: Spare
wheel
s43s.1.book Page 217 Thursday, May 13, 2010 1:21 PM

Page 221 of 275

Breakdown assistance
220
Tightening wheel bolts
– Push the wheel wrench* fully onto the wheel bolt
19).
– Grasp the end of the wrench* and turn the bolt to the right until it is tight.
WARNING
Slacken the wheel bolts only a little (about one turn) as long as the vehicle has
not yet been lifted with the lifting jack* - risk of accident!
Note
Apply pressure carefully with your foot to the end of the wrench* if it proves difficult
to slacken the bolts. Hold tight on the vehicl e when doing this and ensure that you have
a steady position.Raise vehicle
You have to raise the vehicle with the lifting jack* in order to be able to
take off the wheel.Position the lifting jack* by selecting the ja cking point which is closest to the wheel to
be removed fig. 179 . The jacking point is located directly below the engraving in the
lower sill. The engraving is only visible after opening the door.
– Position the lifting jack* below the jacking point and move it up until its claw is
positioned directly below the vertical web of the lower sill. – Align the lifting jack* so that its claw
grasps the web of the lower sill and the
base plate is resting flat on the floor.
– Turn the lifting jack* up further until the wheel is just clear of the ground.
Ground which is soft and slippery below the lifting jack* can cause the vehicle to slip
off the lifting jack*. It is therefore always necessary to place the lifting jack* on a solid
surface or use a wide and stable base. Use a non-slip base (e.g. a rubber foot mat) if
the surface is smooth, such as cobbled stones, a tiled floor, etc.
WARNING

Always raise the vehicle with the doors closed - risk of injury!

Take suitable measures to prevent the ba se of the lifting jack from slipping
off - risk of injury!

Not positioning the lifting jack* at the specified points can result in damage
to the vehicle. The jack can al so slip off if it does not have sufficient grip - risk of
injury!

It is important to support the vehicle with suitable supporting blocks if you
wish to work under the lifted vehicle - risk of injury!
Securing wheels against being stolen*
You need a special adapter for sl ackening the safety wheel bolts.– Pull off the full wheel trim/cap from the wheel hub or cap from the safety wheel
bolt.
Fig. 179 Changing a wheel: Jacking
points for positioning lifting jack
AA
AB
Fig. 180 Safety wheel bolt with adapter
s43s.1.book Page 220 Thursday, May 13, 2010 1:21 PM

Page 233 of 275

Fuses and light bulbs
232
Turn signal light at the frontChanging light bulb for turn signal light (at the front)– Switch the ignition and all lights off.
– Remove the headlight page 231.
– Turn the socket in the direction of arrow OPEN and take it out together with the
light bulb for the turn signal light fig. 191 .
– Press the defective light bulb into the socket, turn to the left and remove.
– Press a new light bulb into the socket and turn the light bulb to the right as far as
the stop.
– Insert the socket with the changed light bulb into the headlight and secure it by turning in the direction of arrow CLOSE to the right.
Note
After installing the headlight, the headligh t setting must be checked by a specialist
garage.
Front parking lights and low beamRemoving the light bulb for the parking light– Switch the ignition and all lights off.
– Remove the headlight page 231.
– Remove the protective cap  page 231, fig. 189.
– Remove the socket fig. 192 .
– Take the faulty bulb out of the fixture and insert a new one.
– Insert the protective cap.Removing the light bulb for the low beam light– Switch the ignition and all lights off.
– Remove the headlight page 231.
– Remove the protective cap  page 231, fig. 189.
– Turn the connector with the light bulb up to the stop towards the left and
remove fig. 192 .
– Replace the lamp, insert the connector with the new lamp and turn to the right up to the stop.
– Insert the protective cap.
Fig. 191 Removing the light bulb for the
turn signal light
Fig. 192 Removing the bulbs for the
parking and low beam light
AB
AA
AB
AB
s43s.1.book Page 232 Thursday, May 13, 2010 1:21 PM

Page 268 of 275

Index267
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
RRadiator fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Rear armrest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73, 90
Rear fog light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Rear window heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Rear window heater . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Rear-view mirror Exterior mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Interior mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Recharge battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Recommendation for changing gears . . . . . . . . . . . 18
Refuelling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Synchronisation process . . . . . . . . . . . . . . . . . . . 44
Replacing fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
Replacing the wiper blades . . . . . . . . . . . . . . . . . . . . 63
Roof aerial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Running in the car . . . . . . . . . . . . . . . . . . . . . . . . . . . 175SSafe securing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Safety information Engine compartment . . . . . . . . . . . . . . . . . . . . . 197
Safety wheel bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
Saving electrical energy . . . . . . . . . . . . . . . . . . . . . . 176
Seat belt height adjuster . . . . . . . . . . . . . . . . . . . . . . 147
Seat belt warning light . . . . . . . . . . . . . . . . . . . . . . . . 147 Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145, 148
Belt tensioners . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
fastening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Height adjustment . . . . . . . . . . . . . . . . . . . . . . . . 147
Safety information . . . . . . . . . . . . . . . . . . . . . . . . 146
taking off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Seat heaters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Selector lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Selector lever lock Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Selector lever positions . . . . . . . . . . . . . . . . . . . . . . . 118
Selector lever-emergency unlocking . . . . . . . . . . . 121
Service Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Service Interval Display . . . . . . . . . . . . . . . . . . . . . . . . 17
Setting temperature Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Side airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Side lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Snow chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
Spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Stability system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 after fuel tank has run empty . . . . . . . . . . . . . . 109
Diesel engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Petrol engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Steering active driver-steering recommendation . . . . 169 Steering force assistance . . . . . . . . . . . . . . . . . . . . . 172
Storage compartment
Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Storage compartments . . . . . . . . . . . . . . . . . . . . . . . . 86
Storage facilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Sun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Sun screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Switching lights on and off . . . . . . . . . . . . . . . . . . . . . 51
Switching off the engine . . . . . . . . . . . . . . . . . . . . . 109
TTaking care of your vehicle . . . . . . . . . . . . . . . . . . . 185
TCS Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125, 132
Temperature outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Temporary spare wheel . . . . . . . . . . . . . . . . . . . . . . 217
the first 1 500 kilometres . . . . . . . . . . . . . . . . . . . . . 175
The roof luggage rack system . . . . . . . . . . . . . . . . . . . 81
Thickness of brake pads Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Tilting roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Tiptronic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Top Tether . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Towing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
towing vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Tow-starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
s43s.1.book Page 267 Thursday, May 13, 2010 1:21 PM

Page:   < prev 1-10 11-20 21-30