SKODA OCTAVIA TOUR 2004 1.G / (1U) Workshop Manual

50CONTROLS AND EQUIPMENTNote

Do not reset the readout between ser-
vice intervals, otherwise an incorrect rea-
dout will be displayed.

The information is retained even if the
vehicle battery is disconnected.

If the instrument cluster is replaced du-
ring repairs, it is necessary to reset the
service interval display. This should be
done by a Škoda Dealership.
It is not recommended to reset the serv-
ice interval display yourself otherwise
this may result in incorrect settings and
thus in possible faults in the vehicle.
After resetting the service interval dis-
play on models fitted with LongLife Serv-
ice*, the service messages are displayed
in the same way as on models not fitted
with LongLife Service.
For this reason we recommend having
the service interval display reset in a
Škoda Dealership. The service interval
display is correctly reset by the Škoda
Dealership using a diagnostic tester.
Fault display
If there is a fault in the instrument cluster,
„dEF“ appears continuously in the display
panel of the trip counter. The fault should
be rectified as soon as possible by a Škoda
Dealer.
5 - Digital clockA knob is provided at the bottom right of
the rev counter for setting the time.

The hours can be set by turning the knob
to the left.

The minutes can be set by turning the
knob to the right.
Warning

Always withdraw the key from the
ignition lock when leaving the car -
even if only for a short time.

For safety reasons, do not attempt
to set the time when driving. When
setting the time, the button should
only be turned and not pressed oth-
erwise the clock may be damaged.
5 - Multi-function display*The information appears in the rev coun-
ter display or in the information display -
see page 53 - depending on the vehicle
equipment.
The multifunctional display shows in
addition to the time a range of further
information:

Outside temperature

Range

Current fuel consumption level

Average fuel consumption

Counter for the distance driven

Average speed

Driving time

Time of day

51
CONTROLS AND EQUIPMENT
The function selector switch and the Re-
set button are located in the handle of the
windscreen wiper stalk.
The functions are displayed one after the
other by repeatedly pressing the top or
bottom side of the function selector switch
with the ignition on. When the ignition is switched on
, the dis-
play switches to the function which had
been selected before switching off the igni-
tion.
If the battery is disconnected for any rea-
son, both memories are erased. Example of readout on models fitted
with large information display*

52CONTROLS AND EQUIPMENTThe memoriesThe system is equipped with two memories
which operate automatically:
A single trip memory 1
collates the following trip data from the
moment the ignition is switched on until it
is switched off: Travelling time, distance
travelled and quantity of fuel consumed.
This information is used to calculate the
average driving speed and the average fuel
consumption.
If the trip is continued within 2 hours after
switching off the ignition, the additional in-
formation is also included in the calculati-
on. The memory is automatically erased if
the trip is interrupted for more than 2 hours.
A total trip memory 2
collates the trip data of any desired number
of individual trips up to a total of 100 hours
travelling time, 10000 km distance and
1000 litres of fuel consumed. These trip
data are used for calculating the average
fuel consumption and speeds achieved
during all the individual trips.If one of the figures stated is exceeded, the
memory is erased and the calculation starts
from the beginning again. Contrary to the
single journey memory, this memory is not
erased after a break in the journey of more
than 2 hours.
Retrieving information
To retrieve the information, select the me-
mories by pressing the
„Reset“ button:
- Single trip memory - 1
- Total trip memory - 2
The following data can be displayed:

Driving time

Distance driven

Average speed

Average fuel consumption
Erasing the memories
The memories can be reset to zero by pres-
sing the „Reset“ button for at least 1 se-
cond.
DisplayingAfter switching on the ignition , the last
readout selected is displayed.
Ambient temperatureThe correct ambient temperature is display-
ed only after 5 minutes. If the car is not mov-
ing or travelling only at a very low speed, the
temperature indicated may be slightly higher
than the actual ambient temperature because
of the heat radiated by the engine.Warning
If the ambient temperature display is
used as an ice warner, do not forget
that black ice may also be present on
the road surface even at tempera-
tures above 0°C. A snow flake sym-
bol is displayed in addition (depend-
ing on vehicle equipment).RangeThis readout indicates the distance which
the vehicle can still travel with the actual
level of fuel in the fuel tank. The figure is
based on the calculation of the average fuel
consumption for the last 50 km. If the dis-
play is reset (after disconnecting and re-
connecting the battery), the vehicle should
be driven 50 km in order to display the re-
levant figure.

53
CONTROLS AND EQUIPMENT
Momentary consumption
l/100 km
The readout indicates the actual consump-
tion in ltr./100 km.
The fuel consumption is calculated in two-
second intervals. If the vehicle is not moving,
the fuel consumption is displayed in l/h.
Average fuel
consumption
∅ l/100 km
What is indicated is the average consump-
tion not the actual consumption at the time
of reading the display.
The average fuel consumption is indicated
after switching on the ignition or erasing the
memory being used, after a distance of
about 300 metres. Up to this point dashes
are displayed instead of a figure.
Single trip memory 1 - what is displayed
is the average fuel consumption of the par-
ticular individual trip.
Total trip memory 2 - what is displayed is
the average fuel consumption which has
been achieved during all individual trips -
see also „Total trip memory“.
Note
The quantity of fuel consumed is not indi-
cated. Distance
km
The remarks made under „Driving time“
also apply in the same way to „Distance
driven“. The maximum distance displayed
is 9999 km.
Average speed
∅
km/h
The remarks made under „Average fuel
consumption“ also apply here in the same
way.
Time no symbol
The time is also displayed even if the igniti-
on is switched off. The clock is set with the
rotary knob - see „Digital clock“, page 50.
Driving time
1 - the driving time which has elapsed since
ignition was switched on or since memory
was deleted - refer to single trip memory,
page 52.
2 - the total driving time of all individual trips
- refer to total trip memory, page 52.
The maximum time displayed in both switch
positions is 99 hours and 59 minutes. If this
figure is exceeded, the display starts again
at zero.
6 - Information display*When the ignition is switched on and the
vehicle is driven, certain functions and the
vehicle status are constantly checked.
Operational faults or repairs which must be
dealt with immediately, or further informa-
tion, is signalled by means of a red and
yellow illuminated symbol in the dash pa-
nel insert in line with the priority. If the sym-
bol lights up, an audible signal also sounds.
In addition, the information and warning
texts appear in the display - see page 56.
Texts or instructions for driver , depend-
ing on the version, can be displayed in one
of the language versions:
English, French, Italian, Spanish, Portugue-
se, German, Czech.
The appropriate language version can be
selected in a Škoda Dealership.

54CONTROLS AND EQUIPMENTThe following information (depending on
the vehicle equipment) appears in the lar-
ge or small display:
- Information and warning texts
- Information of MFD - see page 50
- Warning symbols or warning lamps - seepage 56
- Selector lever position of automatic ge- arbox - see page 39
- Information of service interval display - see page 49
- Information of navigation system Example of readout in small display* Example of readout in large display*

55
CONTROLS AND EQUIPMENT
Navigation system*
Navigation systemOn models fitted with the navigation sy-
stem, it is possible to switch between the
following settings by pressing the switch in
the handle of the windscreen wiper lever
(for more than 2 seconds):

Navigation information

Information of MFD
If the navigation system is operating, prio-
rity is given to displaying the information
and warning texts in the information display. Operation of the navigation system is de-
scribed in separate operating instructions
to be found in the on-board literature.
Operating menu of display *Select the menu in the large information
display by pressing the top part of the
rocker switch on the windshield wiper le-
ver in direction of arrow (for more than 1
second) - see illustration.
You can scroll through the individual dis-
plays with the rocker switch. When you re-
lease the switch, the selected information
is displayed.

56CONTROLS AND EQUIPMENTIndicator/warning lightsThe position of the indicator/warning lights
depends on the model and engine versi-
on. You will find the symbols presented in
the description which follows on or at the
corresponding indicator/warning lights in
the instrument cluster.
When certain warning lights come on, this
is accompanied by an audible signal. A text
may also be shown in the information dis-
play* - see previous chapters.
Turn signal systemThe right or left indicator light flashes when
switching over the turn signal light upwards
or downwards.
If a turn signal fails, the warning light flashes
twice as fast. This does not apply when
towing a trailer. Both warning lights flash
when the hazard warning system is swit-
ched on.Main beamThe warning light comes on when main
beam is switched on or when the headlight
flasher is used.
Further details are given on page 67.Airbag system*The warning light comes on for a few sec-
onds when ignition is switched on.
If the lamp does not go out or if it comes on
again when driving, there is a fault in the
system. This is also valid if the warning light
does not come on when switching on the
ignition. Further information see page 103.
Text in the information display*: AIRBAG
FAULT (fault at airbag)
The operational readiness of the airbag
system is monitored electronically, also on
deactivated front passenger airbag or side
airbag.
WarningIf you do not pay attention to the warn-
ing lights coming on and the corre-
sponding descriptions and warning
notes, this may result in severe body
injuries or major vehicle damage.The engine compartment of your car
is a hazardous area.There is a risk of injuries, scalding,
accidents and fire when working in the
engine compartment, e.g. inspecting
and replenishing oil and other fluids.Absolutely pay attention to the warn-
ing notes - see page 137.

57
CONTROLS AND EQUIPMENT
If the front or side airbag was deacti-
vated with the switch in the glove box:
- the warning light comes on for 3 secondswhen the ignition is switched on;
- the deactivation of the airbag is signaled by the warning light Airbag OFF coming
on in the front interior light
Warning
If a fault exists, have the airbag sys-
tem checked immediately by a Škoda
Dealer. Otherwise, there is a risk of
the airbag or the seat belt not being
activated in the event of an accident.
Trailer turn signal system*The warning light flashes if the turn signal
system is operated when towing a trailer.
If a turn signal light of the trailer or towing
vehicle fails, the warning light does not
flash.Low beamThe warning light comes on after the low
beam is switched on - see page 82.Fog lights*The warning light comes on when the fog
lights are switched on.Rear fog lightThe warning light comes on when the rear
fog light is switched on.
Testing engine electronics* EPC(fitted only to certain engines)
The warning light comes on for a few se-
conds when the ignition is switched on.
If the warning light does not go off or co-
mes on or flashes when driving, this indi-
cates a fault in the engine electronic sy-
stem. A program stored in the engine con-
trol unit makes it possible to continue dri-
ving with certain restrictions - contact a
Škoda Dealer for professional assistance.Glow plugs(diesel engines only)
If the engine is cold, the warning light co-
mes on when the preglow position „2“ (ig-
nition on) is switched on - see page 43. If
the warning light does not come on, there
is a fault in the glow plug system - contact
a Škoda Dealer for assistance. After the
light goes out, start the engine rightaway.
If the engine is warm, the glow plug warn-
ing light does not come on - the engine can
be started straightaway.
If the warning light flashes when driving,
there is a fault in the system.
Contact a Škoda Dealership for professio-
nal advice.

58CONTROLS AND EQUIPMENTCoolant temperature, coolant
levelThe warning light comes on for a few se-
conds after switching on the ignition.
On vehicles with information display, the
warning light does not come on after switch-
ing on the ignition, only if a fault exists or a
lack or coolant.
If the warning light does not go off after this
or flashes when driving, either the coolant
temperature is too high or the coolant level
is too low.
Text in the information display*: STOP CHECK
COOLANT SERVICE MANUAL.
An audible warning signal then sounds
(peep signal 3 times).
If this happens, stop the car and switch
off the engine ; check the coolant level and
top up coolant if necessary.
If the warning light comes on, although the
coolant is at the correct level and the fan
fuse is in proper order, do not drive any
further. The engine must then also not run
in neutral. Contact a Škoda Dealer for pro-
fessional assistance.
Warning

Take care when opening the cool-
ant expansion tank. When the engine
is hot, the cooling system is pressu-
rized - risk of scalding! Allow the
engine to cool down, therefore, be-
fore unscrewing the cap.

Do not touch the fan! The fan may
switch on suddenly - even if the igni-
tion is switched off.
If the coolant is at the correct level, the rise
in temperature may be caused by a failure
of the radiator fan. Check the fuse of the
radiator fan and renew if necessary - see
page 167.
If the warning light does not go out althou-
gh the coolant is at the correct level and
the fan fuse is in proper order, do not drive
any further . Contact a Škoda Dealer for
professional assistance.
Further information is provided on pages
137 and 142.
Brake wear indicator*If this warning light comes on, contact a
Škoda Dealer to have the brake pads chec-
ked.
An audible warning signal sounds (single
peep signal).
In view of the fact that the brake wear indi-
cator monitors only the front brake pads, it
is recommended to also have the rear
brake pads or linings inspected.Fuel levelThe warning light comes on and remains
on if there are only about 7 litres of fuel in
the tank.
An audible warning signal sounds (1 beep).

59
CONTROLS AND EQUIPMENT
Engine oilWarning light shows red
(engine oil level too low)
The warning light comes on for a few se-
conds when the ignition is switched on.
On vehicles with information display, the
warning light does not come on after switch-
ing on the ignition, only if a fault exists or a
shortage of oil.
If the warning light does not go out after a
few seconds or comes on when driving,
stop the car and switch off the engine,
check oil level and top up oil if necessary –
see page 136.
Text in the information display*: STOP! OIL
PRESSURE STOP ENGINE! SERVICE
MANUAL.
An audible warning signal sounds (peep
signal 3 times).
If the warning light comes on although the
oil is at the correct level, do not continue
driving . The engine must also not be run
at idling speed in this case. Contact a
Škoda Dealership for professional advice. Warning
The oil pressure light is not an oil
level indicator! One should therefore
check the oil level at regular inter-
vals, preferably after every refuelling
stop.
Warning light lights up yellow*
(oil in the engine is too low)
If the warning light lights up yellow, the
quantity of oil in the engine is probably too
low.
Check as soon as possible the oil level or
top up with engine oil - see page 140.
An audible warning signal sounds (3x
beeps).
Text in the information display*: CHECK OIL
LEVEL.
Models fitted with LongLife Service: The
oil level warning is reset when the bonnet
is opened. If the engine oil is not replenis-
hed, the warning appears once again after
driving about 100 km.
Yellow warning light flashes*
(engine oil level gauge faulty)
If a fault occurs at the engine oil level gau-
ge, this is indicated by an audible signal and
by the warning light flashing several times.
Text in the information display*: OIL SEN-
SOR WORKSHOP.
Have the engine inspected without de-
lay by a Škoda Dealership.