warning light SKODA RAPID 2014 1.G User Guide
Page 35 of 200
Warning at excessive speeds
An audible warning signal will sound when the vehicle speed exceeds 120 km/
h 1)
. The audible warning signal is switched off when the vehicle speed falls be-
low 120 km/h.
Coolant temperature gauge
Fig. 23 
Coolant temperature gauge
Read and observe  on page 30 first.
Applies to cars with the instrument cluster - Version 1  » Fig. 20 on page 30 .
The display  » Fig. 23 provides information on the engine coolant temperature.
The display only works if the ignition is switched on.
In vehicles with the instrument cluster - version 2,  » Fig. 21 on page 30  the
coolant temperature is indicated only by one of the warning lights  » page 36,
  
  Coolant
 coming on or going off.
Cold range
If the pointer is still in the left area of the scale, this indicates that the engine
has not yet reached its operating temperature. Avoid high speeds, full throttle
and high engine loads. This prevents possible damage to the engine.
The operating range
The engine has reached its operating temperature as soon as the pointer
moves into the middle of the scale 
A
  » Fig. 23 . At very high ambient tempera-
tures or heavy engine loads, the pointer may move even further to the right.
High temperature range
If the pointer reaches the red area of the scale, the coolant temperature is too
high. Further information  » page 36, 
  
  Coolant
.
CAUTION■
Additional headlights and other attached components in front of the air inlet
impair the cooling efficiency of the coolant.■
Never cover the radiator - there is a risk of the engine overheating.
Fuel gauge
Fig. 24 
Fuel gauge
Read and observe 
 on page 30 first.
The display provides information on the fuel level in the container.
Fuel gauge types  » Fig. 24
Display in the instrument cluster - Version 1
In the display of the instrument cluster - Version 2
The display only works if the ignition is switched on.
The fuel tank has a capacity of about 55 litres.
The warning light lights up when the amount of fuel reaches the reserve
zone 
 » page 39 .
The reserve zone is indicated by the red area of the scale » Fig. 24 - 
 or by
displaying only the last two segments of the scale  » Fig. 24 - 
 in the magnify-
ing glass. 
1)
This function only applies to certain countries.
32Using the system    
Page 37 of 200
Some error messages and other information are displayed in the MAXI DOT
display. The messages are displayed simultaneously with the icons in the MAXI
DOT display or with the warning lights in the instrument cluster  » page 34,
Indicator lights .
The menu item  Vehicle status is shown in the main menu of the MAXI DOT
display whenever at least one fault message exists. After selecting this menu,
the first of the error messages is displayed.
If there are several error messages, the display will show  1/3, for example, be-
low the message. This indicates that the first of a total of three error messag-
es is being displayed.
Warning symbols in the MAXI DOT displayEngine oil pressure too low» page 36Check engine oil level,
engine oil sensor defective» page 36Problem with the engine oil pressure» page 34Clutches of the automatic DSG gearbox are
too hot» page 34
  Problem with the engine oil pressure
If the   symbol is shown in the MAXI DOT display, you must have your vehicle
checked immediately by a specialist garage. The information about the maxi-
mum permissible engine speed is displayed together with this symbol.
  Clutches of the automatic DSG gearbox are too hot
A    symbol in the MAXI DOT display indicates that the temperature of the au-
tomatic gearbox DSG clutches is too high.
The following message is shown in the MAXI DOT display. Gearbox overheated. Stop! Owner's manual!
  
do not continue to drive!  Stop the vehicle, switch off the engine, and wait
until the   icon goes out – risk of gearbox damage! You can continue your
journey as soon as the symbol disappears.
WARNINGIf you have to stop for technical reasons, then park the vehicle at a safe
distance from the traffic, switch off the engine and switch on the hazard
warning lights  » page 62. The warning triangle must be set up at the pre-
scribed distance - observe the national legal provisions when doing so.
Note
■ If the MAXI DOT display shows warning messages, these messages must be
confirmed in order to access the main menu  » page 42, Using the information
system  .■
As long as the operational faults are not rectified, the symbols are always in-
dicated again. After they are displayed for the first time, the symbols continue
to be indicated without any extra messages for the driver.
Indicator lights
 Introduction
This chapter contains information on the following subjects:
  Handbrake
35
  Brake system
35
 Seat belt warning light
35
  Generator
35
 Door open
36
  
 Engine oil
36
 
 Coolant
36
  Power steering
37
 Electronic Stability Control (ESC)
37
  Traction Control System (ASR)
37
Antilock brake system (ABS)
37
 Rear fog light
38
  Lamp failure
38
  Exhaust inspection system
38
  Glow plug system (diesel engine)
38
  Engine performance check (petrol engine)
38
  Diesel particulate filter (Diesel motor)
38
 Fuel reserve
39
  Airbag system
39
34Using the system   
Page 38 of 200
 Tyre inflation pressure40  Windscreen washer fluid level40
 
 Turn signal system
40
  Fog lights
40
  Cruise control system
41
  Brake pedal (automatic gearbox)
41
 Main beam
41
The warning lights indicate certain functions or faults.
Some warning lights can be accompanied by acoustic signals and messages in
the display of the instrument cluster.
After switching on the ignition, some warning lights  light up  briefly as a func-
tion test.
If the tested systems are OK, the corresponding warning lights go  out a few
seconds after switching on the ignition or after starting the engine.
WARNING■ Ignoring illuminated indicator lights and related messages or instructions
in the instrument cluster display may lead to serious personal injury or
damage to the vehicle.■
If you have to stop for technical reasons, then park the vehicle at a safe
distance from the traffic, switch off the engine and switch on the hazard
warning lights  » page 62. The warning triangle must be set up at the pre-
scribed distance - observe the national legal provisions when doing so.
■
The engine compartment of your car is a hazardous area. The following
warning instructions must be followed at all times when working in the en-
gine compartment  » page 137, Engine compartment .
 Handbrake
Read and observe 
 on page 35 first.
The warning light   
illuminates  if the handbrake is applied.
An acoustic signal will sound if you drive the vehicle above 6 km/h for at least
3 seconds while the handbrake is applied.
The following message is shown in the MAXI DOT display. Release parking brake!
 Brake system
Read and observe 
 on page 35 first.
The indicator light  
 illuminates  if the brake fluid level in the braking system
is too low or there is a fault in the ABS.
The following message is shown in the MAXI DOT display.
Brake fluid: Owner's manual!
›
Stop the vehicle, switch off the engine, and check the level of the brake flu-
id  » page 144  » .
WARNING■
If the warning light   together with the warning light   » page 37 ,
 Antilock brake system (ABS)  illuminates,  do not continue to drive!
Seek help from a specialist garage.■
A fault to the ABS system or the braking system can increase the vehi-
cle's braking distance – risk of accident!
 Seat belt warning light
Read and observe 
 on page 35 first.
The warning light   
illuminates  as a reminder for the driver and front passen-
ger to fasten seat belts.
The indicator light   
goes off  after the respective seat belt has been fastened.
If the driver or front passenger has not fastened their seat belt and the vehicle
speed is more than 20 km/h, the warning light   
flashes  and you will hear an
acoustic signal.
The warning signal is switched off and the indicator light   is 
permanently lit
if the driver and front passenger have not fastened their seat belts within the
next 90 seconds.
 Generator
Read and observe 
 on page 35 first.
The warning light   
lights up  when the engine is running, the vehicle battery
is not being charged.
Seek assistance from a specialist garage immediately. 
35Instruments and Indicator Lights        
Page 39 of 200
CAUTIONIf in addition to the warning light  the warning light   » page 36 lights up
while driving,   stop driving  - there is a risk of engine damage! Switch off the
engine and seek assistance from a specialist garage.
 Door open
Read and observe 
 on page 35 first.
The indicator light   
illuminates  if one or several doors or luggage compart-
ment lid are opened.
  Engine oil
Read and observe 
 on page 35 first.
The warning light   flashes (low oil pressure)
The following message is shown in the MAXI DOT display.
Oil pressure: Engine off! Owner's manual!
› Stop the vehicle, switch off the engine, and check the engine oil lev-
el  » page 141 .
› If the oil pressure is too low, top up the engine oil 
» page 142.
If the oil level is within the specified range and the warning light  flashes
 again after the engine is started, 
do not continue driving!
Switch off the engine and seek assistance from a specialist garage.
The indicator light   lights up (oil quantity too low)
The following message is shown in the MAXI DOT display.
Check oil level!
› Stop the vehicle, switch off the engine, and check the engine oil lev-
el  » page 141 .
The warning light will  go out if the bonnet is left open for more than 30 sec-
onds  . If no engine oil has been replenished, the warning light will 
come on
again after driving about 100 km.
The indicator light   flashes (engine oil level sensor faulty)
The following message is shown in the MAXI DOT display.
Oil sensor: Workshop!
If the engine oil level sensor is faulty, the warning light   flashes  several
times and an audible signal sounds when the ignition is turned on.
Seek assistance from a specialist garage immediately.
CAUTION
  Stop driving  if for some reason it is not possible to top up the engine oil un-
der the current conditions. Switch off the engine and seek assistance from a
specialist garage.
  Coolant
Read and observe 
 on page 35 first.
The   indicator light remains 
illuminated until the engine reaches operating
temperature 1)
. Avoid high speeds, full throttle and high engine loads.
If the warning light   
lights up  or flashes , either the coolant temperature is
too high or the coolant level is too low.
The following message is shown in the MAXI DOT display. Check coolant! Owner's manual!
›
Stop the vehicle, switch off the engine and check the coolant lev-
el  » page 143 .
›
If the coolant level is too low, add coolant to the reservoir  » page 143.
If the indicator light   
does not illuminate  after adding coolant and switching
on the ignition, you may continue your journey.
If the coolant is within the specified range and the warning light   is still 
lit
after switching on the ignition, then there may be a malfunction of the cooling
fan.
›
Switch off the ignition.
›
Check the fuse for the radiator fan, replace if necessary  » page 171, Fuses in
the engine compartment .
If the coolant level and fan fuse are OK and the warning light   
lights up  again
after switching on the ignition,  do not continue driving!
Seek help from a specialist garage. 
1)
Applies to cars with the instrument cluster - Version 2.
36Using the system      
Page 40 of 200
WARNING■Carefully open the coolant expansion bottle. If the engine is hot, the cool-
ing system is pressurized – risk of scalding! It is therefore best to allow the
engine to cool down before removing the cap.■
Do not touch the radiator fan. The radiator fan may switch itself on auto-
matically even if the ignition is off - a danger of injury is present!
CAUTION
■ Additional headlights and other attached components in front of the air inlet
impair the cooling efficiency of the coolant.■
Never cover the radiator - there is a risk of the engine overheating.
 Power steering
Read and observe 
 on page 35 first.
If the indicator light  
 is  illuminated , there is a fault in the power steering sys-
tem.
The power steering operates with reduced steering assist or does not function
at all.
Seek assistance from a specialist garage immediately.
 Electronic Stability Control (ESC)
Read and observe 
 on page 35 first.
The warning light  
 flashes  to show that the ESC is currently operating.
If the warning light  
 illuminates , there is a fault in the ESC.
The following message is shown in the MAXI DOT display. Error: stabilization control (ESC)
or Error: Traction control (TCS)
Seek assistance from a specialist garage immediately.
If the warning light  
 illuminates  immediately after you start the engine, the
ESC might be switched off due to technical reasons.
›
Switch the ignition off and on again.
If the warning light   does not illuminate  after you switch the engine back on,
the ESR is fully functional again.
Further information  » page 109, Electronic Stability Control (ESC) .
Note
If the vehicle battery has been disconnected and then reconnected, the warn-
ing light   comes on after switching on the ignition. If the warning light does
not go out after moving a short distance, this means that there is an error in
the system. Seek assistance from a specialist garage immediately.
 Traction Control System (ASR)
Read and observe 
 on page 35 first.
The warning light  flashes
 to show that the ASR is currently operating.
If the warning light   
illuminates , there is a fault in the ASR.
The following message is shown in the MAXI DOT display. Error: Traction control (TCS)
Seek assistance from a specialist garage immediately.
If the warning light   
illuminates  immediately after you start the engine, the
ASR might be switched off due to technical reasons.
›
Switch the ignition off and on again.
The ASR is fully functional again if the   warning light 
no longer illuminates
after you switch the engine back on.
Further information  » page 109, Traction Control System (TCS) .
Note
If the vehicle battery has been disconnected and then reconnected, the warn-
ing light   comes on after switching on the ignition. If the warning light does
not go out after moving a short distance, this means that there is an error in
the system. Seek assistance from a specialist garage immediately.
Antilock brake system (ABS)
Read and observe 
 on page 35 first.
If the warning light  
 illuminates , there is a fault in the ABS. 
37Instruments and Indicator Lights         
Page 41 of 200
The following message is shown in the MAXI DOT display.Error: ABS
The vehicle will only be braked by the normal brake system without the ABS.
Seek assistance from a specialist garage immediately.
In the event of an ABS fault, the other braking and stabilization systems are
turned off  » page 109 , Braking and stabilisation systems  .WARNING■
A fault to the ABS system or the braking system can increase the vehi-
cle's braking distance – risk of accident!■
If the warning light  
 together with the warning light  
 » page 35 , 
Brake system  illuminates, 
 do not continue to drive!  Seek help from a
specialist garage.
 Rear fog light
Read and observe 
 on page 35 first.
The warning light   
illuminates  when the rear fog light is switched on.
 Lamp failure
Read and observe 
 on page 35 first.
The warning light   
illuminates  if a lamp is faulty or if an external vehicle lamp
is faulty  .
The indicator light   
illuminates  within a few seconds after switching on the
ignition or when a light with a faulty lamp is switched on .
The following message, for example, may be shown in the MAXI DOT display. INFORMATION Check front right low beam!
The rear side lights and the licence plate lighting have several light bulbs. The indicator light   only lights up if all bulbs in the parking light (in one rear light)
or the licence plate lighting are faulty 1)
. For this reason, regular check that
these light bulbs are working correctly.
 Exhaust inspection system
Read and observe 
 on page 35 first.
If the warning light  
 illuminates , there is a fault in the exhaust inspection
system. The system allows the vehicle to run in emergency mode.
Seek assistance from a specialist garage immediately.
 Glow plug system (diesel engine)
Read and observe 
 on page 35 first.
The warning light   
illuminates  after the ignition has been switched  on. Once
the light has gone out, the engine can be started immediately.
There is a fault in the glow plug system if the warning light   
does not  come
on at all or  lights up continuously .
If the warning light   begins to 
flash while driving, a fault exists in the engine
control. The system allows the vehicle to run in emergency mode.
Seek assistance from a specialist garage immediately.
 Engine performance check (petrol engine)
Read and observe 
 on page 35 first.
If the indicator light   
illuminates , there is a fault in the engine control. The
system allows the vehicle to run in emergency mode.
Seek assistance from a specialist garage immediately.
 Diesel particulate filter (Diesel motor)
Read and observe 
 on page 35 first.
The diesel particulate filter separates the soot particles from the exhaust. The soot particles collect in the diesel particulate filter where they are burnt on a
regular basis.
If the indicator light   
illuminates , soot has accumulated in the filter. 
1)
Applies to vehicles with START-STOP system.
38Using the system        
Page 42 of 200
To clean the filter, and where traffic conditions permit » , drive as follows for
at least 15 minutes or until the indicator light   goes out.
4th or 5th gear selected (automatic transmission: position S).
Vehicle speed at least 70 km/h.
Engine speed between 1800-2500 rpm.
If the filter is properly cleaned, the warning icon  
 goes out .
If the filter is not properly cleaned, the warning light  
 does  not go out  and
the warning light  
 begins to  flash.
The following message is shown in the MAXI DOT display. Diesel particulate filter: Owner's manual!
The system allows the vehicle to run in emergency mode. After switching the
ignition off and on again the indicator light, the indicator light   also 
illumi-
nates .
Seek assistance from a specialist garage immediately.WARNING■ The diesel particulate filter reaches very high temperatures - there is a
fire hazard and serious injury could be caused. Therefore, never stop the
vehicle at places where the underside of your vehicle can come into contact
with flammable materials such as dry grass, undergrowth, leaves, spilled
fuel or such like.■
Always adjust your speed to suit weather, road, region and traffic condi-
tions. The recommendations indicated by the warning light must not tempt
you to disregard the national regulations for road traffic.
CAUTION
■ As long as the warning light   lights up, one must take into account an in-
creased fuel consumption and in certain circumstances a power reduction of
the engine.■
Using diesel fuel with increased sulphur content can significantly reduce the
service life of the diesel particle filter. A ŠKODA Partner will be able to tell you
which countries use diesel fuel with increased sulphur content.
Note
■ To assist the combustion process of the soot particles in the filter, we recom-
mend that regularly driving short distances be avoided.■
If the engine is turned off during the filter cleaning process or shortly after-
wards, the cooling fan may turn on automatically for a few minutes.
 Fuel reserve
Read and observe 
 on page 35 first.
When the warning light  
 is illuminated , this means there is a fuel reserve of
under around 7 litres left.
The following message is shown in the MAXI DOT display.
Please refuel. Range: ... km
CAUTION
Never drive until the fuel tank is completely empty! The irregular supply of fuel
can cause misfiring. This can result in considerable damage to parts of the en-
gine and the exhaust system.
Note
The text in the display goes out only after refuelling and driving a short dis-
tance.
 Airbag system
Read and observe 
 on page 35 first.
If the warning light  
 illuminates , there is a fault in the airbag system.
The following message is shown in the MAXI DOT display. Error: Airbag
The functionality of the airbag system is monitored automatically even if one
of the airbags is switched off.
The front passenger airbag has been disabled with the key switch
› The indicator light 
 illuminates  for around 4 seconds after the ignition has
been switched  on;
› The warning light 
 
 in the display  
 
 
 
 
 in the middle of the
dash panel lights up after switching on the ignition  » Fig. 12 on page 20 .
One of the airbags or a belt tensioner has been disabled by the diagnostic
tool
› The warning light 
 illuminates  for approx. 4 seconds after switching  on the
ignition and then  flashes again for approx. 12 seconds afterwards.
The following message is shown in the MAXI DOT display. Airbag / belt tensioner deactivated. 
39Instruments and Indicator Lights         
Page 43 of 200
WARNINGWhen a fault in the airbag system occurs, there is a risk of the system not
being triggered in the event of an accident. Therefore, this must be
checked immediately by a specialized company.
 Tyre inflation pressure
Read and observe 
 on page 35 first.
The warning light   is illuminated
If the warning light   illuminates while driving, it means one of the tyres has
undergone a pressure change.
An audible signal sounds as a warning signal.
›
Immediately reduce speed and avoid sudden steering and braking manoeu-
vres.
›
Stop the vehicle, turn the ignition off and check the tyres and their inflation
pressure  » page 149 .
›
Correct the tyre pressure, if necessary or replace the affected
wheel  » page 156  or use the repair kit  » page 160.
›
Store the tyre pressure values in the system  » page 115.
The indicator light   flashes for about 1 min. and remains lit
If the warning light   flashes for approximately 1 minute and stays on, there
may be a fault in the tyre pressure monitoring system.
›
Stop the vehicle, turn the ignition off and start the engine again.
If the warning light   flashes again after the engine has started, there is a
system error.
Seek help from a specialist garage.
The following reasons can explain the warning light   being illuminated.
› The vehicle is loaded on one side. Distribute loads as evenly as possible.
› The wheels of one axle are loaded more heavily (e.g. when towing a trailer or
when driving uphill or downhill).
› Snow chains are mounted.
› A wheel has been changed.
Store the tyre pressure values in the system  » page 115.
CAUTIONUnder certain circumstances (e.g. sporty style of driving, wintry or unpaved
roads) the warning light   in the instrument cluster can be delayed or does
not light up at all.
Note
If the vehicle battery has been disconnected and then reconnected, the warn-
ing light   comes on after switching on the ignition. If the warning light does
not go out after moving a short distance, this means that there is an error in
the system. Seek help from a specialist garage.
 Windscreen washer fluid level
Read and observe 
 on page 35 first.
If the windscreen washer fluid level is too low, the warning light  
 illumi-
nates .
The following message is shown in the MAXI DOT display. Top up wash fluid!
Top up with liquid  » page 139, Windscreen washer system .
  Turn signal system
Read and observe 
 on page 35 first.
Either the left  
 or the right  
 warning light  flashes depending on the position
of the turn signal lever.
If there is a fault in the turn signal system, the warning light  flashes at twice
its normal rate.
Switching off the hazard warning light system is switched on will cause all of
the turn signal lights as well as both warning lights to  flash.
 Fog lights
Read and observe 
 on page 35 first.
The warning light  
 illuminates  when the fog lights are operating.
40Using the system        
Page 44 of 200
 Cruise control systemRead and observe 
 on page 35 first.
The warning light  
 illuminates  when the cruise control is active  » page 111.
 Brake pedal (automatic gearbox)
Read and observe 
 on page 35 first.
If the warning light  
 illuminates , operate the brake pedal.
 Main beam
Read and observe 
 on page 35 first.
The warning light   
illuminates  when the main beam or the headlight flasher
is operated.
Information system
Driver information system
 Introduction
This chapter contains information on the following subjects:
Using the information system
42
Display a low temperature
42
Gear recommendation
43
Door, boot or engine compartment warning
43
The information system provides the driver with alerts and messages about in-
dividual vehicle systems.
This information and advice is shown in the instrument cluster display or indi-
cated by the illumination of the corresponding indicator light in the instrument
cluster.
The information system provides the following information and instructions
(depending on vehicle equipment).
› Data relating to the multi-function display (MFD) 
» page 43.
› Data relating to the MAXI DOT display 
» page 46.
› Service interval display 
» page 47.
› Auto Check Control 
» page 33.
› Selector lever positions for an automatic gearbox 
» page 105.
WARNINGConcentrate fully on your driving at all times! As the driver, you are fully re-
sponsible for the operation of your vehicle.41Information system     
Page 46 of 200
Gear recommendationFig. 27 
Information on the selected
gear / Gear recommendation
Read and observe  on page 41 first.
The function of the gear recommendation is to help reduce fuel consumption.
A suitable gear is engaged, if necessary, a recommendation to shift to high or
lower gear is displayed.
Display  » Fig. 27
Optimal gear engaged
Recommended gear
Recommended gear
The gear recommendation is intended only for vehicles with a manual trans- mission or for vehicles with an automatic transmission in manual shift mode
(Tiptronic).
The  recommended  1)
 gear and the arrow icon  2)
 is displayed.
› 
 - Recommends that you shift to a 
higher gear
› 
 - Recommends that you shift to a 
lower gear
If for example   is shown in the display with vehicles that have 
manual gear-
boxes  this indicates that it is better to shift from a lower gear to the 4th gear.
If for example   is shown in the display with vehicles that have 
automatic
gearboxes  and are in the manual switching mode (Tiptronic), this indicates
that it is better to shift from the 4th gear to a higher gear.
WARNINGThe driver is always responsible for selecting the correct gear in different
driving situations, such as overtaking.
For the sake of the environment
A suitably selected gear has the following advantages.■It helps to reduce fuel consumption.■
It reduces the operating noise.
■
It protects the environment.
■
It benefits the durability and reliability of the engine.
Door, boot or engine compartment warning
Read and observe 
 on page 41 first.
Vehicles with a MAXI DOT display
If at least one door, the boot or bonnet is open, the display indicates the rele-
vant  open  door, boot or bonnet vehicle icon.
Vehicles with a segment display
If at least one door or the tailgate is open, the  
 warning light in the instru-
ment cluster lights up  » page 36.
An acoustic signal will also sound if you drive the vehicle above 6 km/h when a door is open.
Multifunction display (MFD)
 Introduction
This chapter contains information on the following subjects:
Memory
44
Information overview
45
Warning at excessive speeds
46
The driving data is displayed on the multifunction display. 
1)
With vehicles that have an automatic gearbox and in the manual switching mode (Tiptronic) the 
current-
ly engaged gear is  shown.
2)
For vehicles with segment display the arrow is displayed behind the gear indication.
43Information system