warning SSANGYONG KORANDO 2012 Owner's Manual

14-190000-00
3. CAN COMMUNICATION (Charge Warning Lamp)
Overview ▶
Meter cluster
(charge warning lamp)
The meter cluster receives the charge warning lamp ON signal from ECU through CAN line.
Charge warning lamp ON conditions
Pre-warning
When DTC related EEM set
Open or short circuit in alternator -
-
-
Circuit diagram ▶

01-8
Steering wheel remote
control switchPassenger door switch
Lower main panel
switch
Start/stop switch
Cruise control switch
Hazard warning switch
bezel assembly
Multifunction switch
FATC switch
Drive door main switch
& Outside rearview mirror
switch
3. SWITCH SYSTEM LAYOUT

03-4
2. FUNCTIONS
1) Functional List
FunctionSKM
without
BCMSKM
with
BCM
1 Wiper control Wiper mist & washer coupled wiper O O
Auto washer coupled wiper O O
Auto light-rain sensor coupled wiper (LIN) O O
Speed sensitive intermittent wiper O O
Wiper low/high control O O
2 Key reminder warning Key reminder warning O X
Ignition key reminder O X
External buzzer control X O
Anti-lock function when opening door O O
3 Tail lamp control Tail lamp ON warning O O
External lamp warning display X O
Tail lamp auto OFF O O
4 Door ajar warning Door status management X O
Door ajar warning O O
5 Seat belt control Seat belt warning O O
Seat belt reminder O O
6 Sunroof warning Sunroof warning control O O
Sunroof warning display X O
7 Room lamp control Door coupled room lamp and dimming control O O
Room lamp OFF control O O
Room lamp control display X O
8 Key hole illumination
controlKey hole illumination O X
9 Defogger (heated wire)
controlFront defogger timer O O
Rear defogger timer
OO

03-6
FunctionSKM
without
BCMSKM
with
BCM
15 Theft deterrent control Theft deterrent mode control in
controlOX
Theft deterrent mode control in smart BCM X O
16 Time lag power
window controlTime lag power window control O O
17 System power sleep
modeSystem power sleep mode control O O
18 Flasher (blinking)
functionLH turn signal control O O
RH turn signal control O O
Hazard warning flasher switch control O O
Hazard warning flasher indicator control X X
Auto hazard warning flasher control O O
Emergency hazard warning flasher control
(coupled with ABS)OO
19 DRL (Daytime Running
Light) controlDRL (Daytime Running Light) control X X
20 Fog lamp control Fog lamp control O O
21 Auto light
control (LIN)Auto light control O O
22 Immobilizer function Key coding and synchronization O X
Challenge O X
CAN information O X
23 Mirror folding/unfolding
controlFolding/unfolding control O O
Auto folding/unfolding control O O
24 Approach (puddle)
lamp control
Approach (puddle) lamp control in BCM without
SKMOX
Approach (puddle) lamp control in BCM with
SKMXO
25 SKM warning buzzer
controlSKM warning buzzer control X O
26 Diagnosis function O O

03-78710-01
3. MAJOR CHANGES
Emergency hazard warning flasher control
Previous Current
Operating condition
If the emergency braking signal is received, the
hazard warning flasher blinks 4 times/second for
10 seconds.
Deactivation conditions:
Returns to normal operation after blinking 4
times/second
Deactivated when hazard warning flasher
switch is pressed once during operation by
emergency braking signal 1.
2.Operating condition
If the emergency braking signal is received, the
hazard warning flasher blinks 4 times/second for
10 seconds.
Operation priority
Hazard warning flasher switch → Emergency
braking signal → Emergency hazard warning
flasher → Multi-function automatic hazard
warning flasher
Deactivation conditions:
Vehicle speed exceeds 50 km/h when
emergency braking signal is received
(activated at speed of 50km/h or less)
Vehicle speed increases more than 10 km/h
above the speed when the signal is received
during operation by emergency braking signal
Turn emergency hazard warning flasher switch
OFF during operation by emergency braking
signal
Deactivated automatically 10 seconds after if
items 2) and 3) above are not met during
operation by emergency braking signal
If multi-function automatic hazard warning
flasher signal is received during operation by
emergency braking signal, it will be overridden. 1.
2.

03-98710-01
1. OVERVIEW & FUNCTIONS
BCM (Body Control Module) controls the electric equipment on car body and outputs the control and
warning signals as below.
List Function List Function
1 Wiper control 14 Tailgate open control
2 Ignition key reminder warning 15 Theft deterrent
3 Tail lamp control 16 Time lag power window control
4 Door ajar warning 17 System power sleep mode
5 Seat belt control 18 Flasher function
6 Sunroof warning 19 DRL (daytime running lamp) control
7 Room lamp control 20 Fog lamp control
8 Key hole illumination control 21 Auto light control (LIN)
9 Defogger control 22 Immobilizer function
10 Keyless entry function 23 Folding/unfolding function
11 Door lock/unlock control 24 Approach (puddle) lamp control
12 Panic alarm 25 SKM warning buzzer control
13 Headlamp control (escort) 26 Diagnosis function
<Table 1>

03-218710-01
2) Ignition Key Reminder
Key reminder warning
(This function has priority over the "Tail lamp on warning".) ▶
When opening the driver door while the ignition key is inserted into the key cylinder, the buzzer sound
for 10 seconds with the interval of 0.02 s ON and 1.38 s OFF.
When removing the ignition key or closing the driver door during the buzzer output (within 10
seconds), the buzzer stops its operation.
This function is not available when the ignition switch (IGN1) is in "ON" position. 1.
2.
3.

03-24
3) Tail Lamp
Tail lamp left ON warning (sunroof and ignition key reminder functions have priority) ▶
The buzzer sounds for 10 seconds with the interval of 0.02 s ON and 1.38 s OFF when opening the
driver door with the key removed (without SKM)/with IGN OFF or ACC (with SKM) and tail lamp ON.
The buzzer stops its operation when turning off the tail lamp or closing the driver door during buzzer
operation. The buzzer stays ON when turning the tail lamp on again after turning it off during buzzer
operation.
This function is not available when the ignition switch (IGN1) is in ON position. 1.
2.
3.

03-258710-01
Tail lamp auto OFF ▶
When opening and closing the driver door after turning off the ignition with the tail lamp ON, the tail
lamps go off automatically.
The tail lamps come on again when inserting the ignition key (without SKM) and turning on the
ignition (with SKM) after tail lamp auto OFF.
The tail lamp should not go off when turning on the tail lamp switch with the ignition key removed
(without SKM) and with power off or ACC ON (with SKM). 1.
2.
3.
Tail lamp ON warning (with SKM) ▶
The tail lamp ON warning signal is sent via the BCAN communication when the tail lamp remains ON
with the ignition key OFF or ACC. 1.

03-26
4) Door Ajar Warning
While the BCM without SKM controls the warning lamp, the BCM with SKM controls the warning lamp
and sends the signal via the BCAN communication. But, this control is available only when any of doors
or tailgate, except engine hood, is open.
The instrument cluster controls the door ajar warning lamp according to the signal from the BCM.
(However, the BCM controls the door ajar warning lamp with the electric wire together with the BCAN
communication.)
Also, the instrument cluster controls the blinking function according to the vehicle speed.
(However, the BCM controls the door ajar warning lamp blinking with the electric wire together with
the BCAN communication.) 1.
2.
(*1) : Ajar: Driver, passenger, rear door or tailgate is open
Close: Driver, passenger, rear door and tailgate are closed