warning SSANGYONG KORANDO 2012 Workshop Manual

04-198712-03
4) Smart Key Verification Time Control
(1) Pre-verification timer
When the operation signal from the START switch is received, the START & power control functions can
be performed without smart key verification.
(2) Immobilizer verification timer
The immobilizer verification status indicates that it is possible to respond to the request message sent
from the EMS to deactivate the immobilizer. The SKM verified a smart key and the engine can be
started.
The 30-second immobilizer verification time is started when:
the ignition status is changed to IGN by the START switch while the pre-verification timer is activated.
the ignition status is changed to IGN by the smart key verification while the pre-verification timer is
stopped; the SKM verified a smart key by the brake switch signal while the immobilizer verification
timer is stopped or the ignition status is IGN ON.
the SKM verified a smart key successfully if the immobilizer verification timer is stopped with IGN
ON/immobilizer verification /brake switch ON. -
-
-
Condition SKM operation
- when door closed signal is input with - B+ or ACC ON
- when brake is applied with - B+ or ACC ON
- when START switch is operated with - B+
- when smart key is inserted into slot & brake switch is
operated or START switch is operated with - B+Once the vehicle interior verification
is completed, 30 sec. pre-verification
timer is started
when the ignition is turned OFF with IGN ON and engine
running 30 sec. pre-verification timer is
started without re-verification
Timer deactivation conditions: after 30 sec. has passed, IGN ON, Outside door handle switch ON,
entering theft deterrent mode when door condition is changed
IGN1 OFF
30 sec. has passed after immobilizer verification
Any door is opened and then closed when all doors are closed & smart key out
When the engine starts to run, the immobilizer verification status is determined, and the immobilizer will
not be deactivated until the ignition status is changed to IGN/ACC/OFF.
The immobilizer is not deactivated when the key out warning condition is met while the engine is
running. (when the RND is received by the EMS reset while the engine is running)
When attempting to start the engine without immobilizer verification, the system performs smart key
verification procedures, and sends the engine start request to EMS only when the verification result is
normal. -
-
-
*
*
*Entry conditions ▶
Deactivation condition ▶

04-278712-03
8) SKM Warning Control
(1) Smart key not found warning (Key out warning)
If no verified smart key is identified as being in the vehicle with IGN ON or ACC ON, the SKM sends the
signal, which identifies that there is no verified key inside the vehicle, to the BCM and instrument cluster
through the BCAN (Smart key not found warning). This warning continues for up to 10 sec. until the
warning condition is deactivated.
The SKM stops the warning immediately after the warning condition is deactivated.
Initial condition:
& & &
Operation by driver
<006b009600960099009a006100470063006b009600960099009a004700960097008c00950047008c009f008a008c0097009b0047008b00990090009d008c0099004e009a0047008b00960096009900650047004d00470063007b008800900093008e008800
9b008c004700960097008c0095006502e70047006300680093>l doors closed> &

SKM operation -
-
-
The SKM starts to identify a smart key by using the interior antenna after confirming that all the
doors are closed through CAN communication.
If no smart key is found it sends the signal for [Smart key not found warning].
* No cyclic smart key searching after transmission
If a smart key is found, no operation is performed.
- Smart key not found warning deactivation conditions
If below conditions are met, the SKM sends the signal for [Smart key not found warning]
to deactivate the warning.
: OR OR 1.
2.
3. Smart key not found warning with ACC ON ▶
Smart key not found warning with IGN/ENGINE ON ▶
Initial condition:
& & &
Operation by driver
<006b009600960099006100470063006b009600960099004700960097008c009500650047004d00470063007b008800900093008e0088009b008c004700960097008c00950065004702e7004700630068009300930047008b009600960099009a0047008a00
930096009a008c008b00650047004d00470063007b00880090>lgate closed>
SKM operation -
-
-
The SKM starts to identify a smart key by using the interior antenna if the [Smart key not found
warning] signal is not output.
a. If no smart key is found it sends the signal for [Smart key not found warning].
b. If a smart key is found, no operation is performed.
The SKM searches for a smart key inside the vehicle at 3 sec. intervals while the [Smart key not
found warning] signal is output.
a. If no smart key is found it sends the signal for [Smart key not found warning].
b. If a smart key is found it sends the signal for [Smart key not found warning
deactivation] signal to deactivate the key out warning. 1.
2.

04-28
Smart key not found warning deactivation conditions
If below conditions are met, the SKM sends the signal for [Smart key not found warning
deactivation] to deactivate the warning. -
A smart key is found while the smart not found warning signal is output.
OR 1.
2.
(2) Smart key detection warning
When a valid smart key sends the LOCK signal from outside of the vehicle or the outside door handle
switch is pressed with no smart key outside, the smart key detection warning signal is output, provided
that all the doors or the tailgate is closed with IGN OFF or ACC ON and a smart key is in the vehicle.
Smart key detection warning conditions ▶
When a valid smart key sends the LOCK signal from outside of the vehicle, the SKM sends the signals
for [external buzzer] and [smart key detection warning] to the BCM and instrument cluster through the
BCAN to inform the driver of the existence of a verified key inside the vehicle, provided that all the doors
or the tailgate is closed with IGN OFF or ACC ON and a smart key is in the vehicle.
Smart key inside vehicle warning 2.
If a smart key including immobilizer slot is identified as being in the vehicle after the outside door handle
switch is pressed, the SKM sends the signals for [external buzzer] and [smart key detection warning] to
the BCM and instrument cluster through the BCAN to inform the driver of the existence of a verified key
inside the vehicle.
These 2 warnings (external buzzer, smart key detection warning) continue for up to 10 sec. until the
warning conditions are deactivated under the above conditions.
The SKM stops these warnings immediately after the warning conditions are deactivated. -
Smart key detection warning deactivation conditions ▶Deactivation warning 1.
Function stop warning deactivation conditions 1.
When theft deterrent deactivated
The SKM sends the signals for [external buzzer] and [smart key detection warning
deactivation].
Smart key inside vehicle warning deactivation conditions
When the door is opened and then closed and no smart key is found, the SKM sends the
signals for [external buzzer] and [smart key detection warning deactivation]. -
-

04-298712-03
(4) Smart key battery discharge warning (3) Smart key verification fail warning
When the verification is requested for ignition status change or engine starting and no verified smart key
is in the vehicle, the SKM sends the [smart key verification status] signal, which indicates that the
verification has failed, for up to 10 sec. until the verification fail conditions are deactivated.
Verification fail detection and transmission conditions ▶
When the ignition status is changed after a smart key is verified by the START switch ON input, the
SKM sends the verification status for 10 sec. -Normally, the smart key verification warning is one of the smart key fail conditions. -
Ignition status change
(OFF ->ACC) / (OFF ->IGN)/(ACC ->IGN) / (IGN -> engine ON) *
If above conditions are met again, the SKM re-verifies a smart key and sends the verification status for
another 10 sec.
When the ignition status is changed by the transponder verification while the smart key status is sent
through the BCAN, the SKM sends the smart key verification signal and also sends the transponder
verification signal for 10 sec. -
-
If low smart key battery is detected during the verification process for ignition status change or engine
start, the SKM sends the signal for [smart key battery low voltage warning] to the BCM and instrument
cluster through the BCAN for up to 10 sec. until the warning condition is deactivated.
Smart key battery discharge confirmation and deactivation ▶
If the smart key battery low voltage is confirmed, the SKM sends the smart key battery low voltage
warning signal.
If the smart key battery is in normal condition, the SKM sends the smart key battery low voltage
warning deactivation signal.
The smart key is the last used key. -
-
*
(5) Transponder verification fail warning
If a verified smart key is not found by the key verification process, the SKM sends the information that
indicates the key is not verified to the instrument cluster through the BCAN for up to 10 sec. until the
verification fail condition is deactivated.
The SKM sends the transponder verification warning when the verification has failed with the smart key
inserted into the immobilizer holder. -
Transponder verification fail detection and transmission conditions ▶
When the ignition status is changed after the transponder is verified by the START switch ON input,
the SKM sends the transponder verification status for 10 sec. -

04-30
Ignition status change
(OFF ->ACC) / (OFF ->IGN)/(ACC ->IGN) / (IGN -> engine ON) *
If above conditions are met again, the SKM re-verifies the transponder and sends the verification
status for another 10 sec.
When the ignition status is changed by a smart key verification while the transponder verification is
processed, the SKM sends the signal for [transponder verification fail], and sends the smart key
verification status for 10 sec. -
-
(6) Transmission position warning
When the gear selector lever is in a position other than P or N with IGN ON and engine started, the
SKM sends the [gear position warning] signal to the instrument cluster through the BCAN for up to 10
sec. until the operating conditions are deactivated.
Transmission position warning deactivation ▶
When re-attempting to start with IGN1 ON and transmission in P or N -
(7) SKM error alert
The SKM sends the SKM error alert signal to the instrument cluster through the BCAN for up to 10 sec.
when an in ignition status related error or passive entry system error occurs.
SKM error transmission conditions ▶
When any of the following errors is detected and a DTC is set, the SKM sends the error alert signal for
10 sec.
B+ (power) low voltage
B+ (logic) low voltage
ACC ON fail
ACC OFF fail
IGN1 ON fail
IGN1 OFF fail
IGN2 ON fail
IGN2 OFF fail
Short circuit in START switch 1.
2.
3.
4.
5.
6.
7.
8.
9.
The SKM sends the corresponding signal only once for 10 sec. when any of the above errors is detected
with IGN OFF/ON. It sends the signal again when a new error occurs.

04-318712-03
(8) Brake not working alert
The SKM sends the brake not working alert signal for 10 sec. every time the ignition status is changed
after the 1st cycle (OFF-ACC-IGN-ACC-OFF) while the brake is not operated.
when the brake pedal is depressed, the system is reset and alert deactivation signal is sent.
when the 10 min. timer is terminated -
-
(9) Clutch not working alert
The SKM sends the clutch not working alert signal for 10 sec. every time the ignition status is changed
after the 1st cycle (OFF-ACC-IGN-ACC-OFF)
while the clutch is not operated.
when the clutch pedal is depressed, the system is reset and alert deactivation signal is sent.
when the 10 min. timer is terminated -
-
(10) Smart key slot detection alert
The SKM sends the smart key slot detection alert signal for 10 sec. when a smart key inserted into
the slot is detected with IGN OFF and the driver's door open. -
(11) SKM alert priority
1 Smart key out alert EXTERIOR
1
2 Smart key reminder alert EXTERIOR
3 Smart key verification fail alert INTERIOR
2 4 Transponder verification failure alarm INTERIOR
5 Smart key battery low voltage alert INTERIOR
6 Transmission position alert INTERIOR
7 SKM error alert INTERIOR
8 Brake alert INTERIOR
9 Clutch alert INTERIOR
10 Smart key slot reminder alert INTERIOR1
Warning cancellation requirements ▶
Warning cancellation requirements ▶
Warning transmission conditions ▶
Warning cancellation requirements ▶
when the smart key is removed, the alert deactivation signal is sent.
when the 10 min. timer is terminated -
-

05-4
2. MAJOR CHANGES
SVC class
Previous Current
Rearranged pre-warning indicator which comes on and goes off when turning ignition on.
1) Steering wheel heating indicator added
2) Pre-warning indicator rearranged
3) Winter mode indicator added(DSL only)
STD class
Previous Current
Winter mode indicator added (one green LED)
SVC class
Previous Current
One indicator added since steering wheel heating function is equipped.

05-58010-01
Previous Current
Ambient temperature also displayed on vehicle with manual A/C control switch
Both SVC and STD class
Previous Current
Warning lamp symbols fulfil ISO standards used on all models
(e.g. 4WD CHECK indicator symbol)
4) Warning lamps according to ISO standards
5) Ambient temperature display
SVC class
This is displayed for 2 seconds when activating winter mode, displayed for 2 seconds when deactivating
winter mode and displayed for 4 seconds when starting engine and driving off (DOT LCD message).
AutomaticAutomatic
Manual
SVC classSVC class
STD class

05-6
SVC class
Previous Current
Changed from figure type to bar graph type.
6) Average fuel economy reset and calibrated automatically when
refilling
7) Instant fuel consumption display changed
8) Pre-warning indicator for engine overheat removed
Both SVC and STD class
Previous Current
Reset by user Reset by user and automatic reset when refilling
9) TDMS logic changed
SVC class
Current
TDMS (Tier Direction Management System) is not displayed when EPS warning lamp comes on.
SVC class STD class
Pre-warning indicator for engine overheat is removed.
EPS warning lampTDMS displayLCD not displayed
EPS warning lamp
comes onLCD screen is not
displayed.

05-98010-01
1) SVC
3. Description of Warning Lamps & Indicators