engine SSANGYONG MUSSO 1998 Workshop Repair Manual

1B1-104 M162 ENGINE MECHANICAL
UNIT REPAIR
OIL GALLERY IN CRANKCASE
Preceding Work : Removal of crankshaft, removal of oil spray nozzle
1 Plug
2 Steel Ball
Cleaning Procedure
1. Remove the plug (1) with a screwdriver.
2. Using a round bar (3) and hammer, remove the steel ball
(2).
3. Using the compressed air, blow into the oil galleries and
clean it off.3 Round Bar...................................
f11 x 750 mm

M162 ENGINE MECHANICAL 1B1-105
1 Plug....................................................... Replace
2 Main Oil Gallery
Tools Required
102 589 12 15 00 Drift
Sealing Procedure
1. Enlarge the end of main oil gallery (4) to be diameter of
16mm, depth of 15mm.
2. Using an M16 x 1.5 thread (tap), make the thread at the
end of main oil gallery (4).
3. Throughly clean the oil gallery with compressed air and
tighten the screw plug (M16 x 1.5) after applying sealing
bond on it.
4. Apply Loctite 270 on new plug and tighten to the hole until
the drift is stopped after inserting new plug into the drift.3 Screw Plug

1B1-106 M162 ENGINE MECHANICAL
OIL GALLERY IN CYLINDER HEAD
Preceding Work : Removal of cylinder head
Removal of camshaft
Removal of tappet
1 Screw Plug................................................ 15 Nm
2 Seal
Cleaning Procedure
1. Remove the screw plug (1) and the seal (2).
Installation Notice
Replace the seal with new one.
2. Clean the oil gallery using the compressed air.
3 Steel Ball (f8mm)
Tightening Torque 15 Nm

M162 ENGINE MECHANICAL 1B1-107
Sealing Procedure
1. Remove the screw plug (1) and the seal.
Installation Notice
2. Remove the steel ball from the oil gallery (4), (5), (6) and
(7) using the round bar (12,
f6 x 700 mm).
4. Enlarge the oil gallery at the rear of the cylinder head to be
diameter 9mm, depth 8mm.
5. Tap in the steel ball (3) from the side to the oil gallery using
the punch (13).
6. Pull out the steel ball (3) using the round bar (12).
7. Enlarge the oil gallery to be diameter 9mm, depth 8mm.
Tightening Torque 15 Nm
3. Remove the plug (8) using the screw driver.

1B1-108 M162 ENGINE MECHANICAL
11. Tighten the screw plug with the seal (arrow).
Screw Plug (Part No. 000 908 01 00 02)
Seal (Part No. 007 603 01 01 03)
8. Make a screw hole at the oil gallery using M10 x 1 thread.
9. All the oil gallery should be cleaned with the compressed
air.
10. Apply the Loctite 270 to new plug and press in using a
suitable drift (arrow).

M162 ENGINE MECHANICAL 1B1-109
CORE PLUGS IN CRANKCASE
Preceding Work : Draining of the coolant
1 Core Plug............................................... Replace

1B1-110 M162 ENGINE MECHANICAL
Tools Required
102 589 00 15 00 Drift
Replacement Procedure
1. Remove the intake and exhaust manifolds.
2. Pull back the core plug until the end of one side comes out
using the screw driver.
3. Pull out the plug carefully using a pliers.
5. Press in new plug using a drift.
Notice
Wait for about 45minutes before filling the coolant so that
the Loctite 240 hardens.
6. Warm up the engine and check the coolant for leaks. 4. Clean the sealing surface and apply Loctite 241.

M162 ENGINE MECHANICAL 1B1-111
Group Code Letter and Cylinder Bore Size
Repair Size
1) The group code letters are carved on the surface of the piston crown and in the mating surface of the crankcase.
CYLINDER BORE
Group Code Letter of Cylinder
A
X
B
X + 5
X + 10Piston Type to be Used
A or X
A, X or B
X or B
X + 5
X + 10Cylinder Bore Size (mm)
f 89.900 - f 90.906
f 89.906 - f 89.912
f 89.912 - f 89.918
f 89.950 - f 89.968
f 90.000 - f 90.018
Type
Standard Size
f 89.9
1st Repair Size
(Standard Size + 0.25)
2nd Repair Size
(Standard Size + 0.5)Group Code Letter
1)
A
X
B
A
X
B
A
X
BCylinder Bore Size (mm)f 89.900 - f 90.906
f 89.906 - f 89.912
f 89.912 - f 89.918
f 90.150 - f 90.156
f 89.156 - f 90.162
f 90.162 - f 90.168
f 90.400 - f 90.406
f 90.406 - f 90.412
f 90.412 - f 90.418

1B1-112 M162 ENGINE MECHANICAL
Service Data Standard
Measurement of Cylinder Bore
1. Clean the cylinder wall.
2. Using a internal diameter gauge, measure the bore size in
axial and transverse direction at three points (1,2,3).
1,2,3. Measuring Points
A . Axial Direction
B. Transverse Direction
a. Location of the No.1 Piston Ring at TDC
b. Location of the Piston BDC
c. Location of the Oil Ring at BDC
Chamfer Angle
Wear Limit in Longitudinal and Transverse Direction
Permissible Deviation of Cylinder Out-of-round
Permissible Deviation of Rectangular Cylinder Height (Except Chamfered Area)
Basic Peak-to-valley Height After Final Honing and Brushing
Chamfer Angle
Honing AngleWhen new
Wear limit0.1 mm
0.007 mm
0.05 mm
0.05 mm
0.003 - 0.006 mm
60°
50° ± 10°

M162 ENGINE MECHANICAL 1B1-113
CRANKCASE MATING SURFACE
Service Data Standard
Height of The Crankcase “H” (When new)
Minimum Height After Milling
Flatness
Permissible Deviation of Parallelism of The
Upper to Lower Mating Surface
Peak-to-valley HeightCrankcase Upper Mating Surface
Crankcase Lower Mating Surface
Axial Direction
Transverse Direction
Crankcase Upper Mating Surface
Crankcase Lower Mating Surface282.25 - 282.35mm
281.95mm
0.03mm
0.04mm
0.1mm
0.05mm
0.005 - 0.020mm
0.025mm