radiator SSANGYONG MUSSO 1998 Workshop User Guide

M161 ENGINE MECHANICAL 1B2-11
10. Remove the upper mounting bolts of radiator and then
remove the radiator.
7. Loosen the cylinder block drain plug and then drain the
coolant completely.
Installation Notice
Tightening Torque 30 Nm
Notice
Replace the seal before installation of the drain plug.
8. Remove the cooling fan shroud.
9. Disconnect the each hose from radiator.

OM600 ENGINE MECHANICAL 1B3-13
4. Remove the radiator drain cock and drain the coolant.
Notice
Open the coolant reservoir tank cap.
3. Remove the skid plate.
Installation Notice
Tightening Torque 28 - 47 Nm
5. Remove the drain plug (1) and seal (2) from the cylinder
block and drain the coolant completely.
6. After draining, replace the seal and reinstall the drain plug.
Installation Notice
7. Disconnect the lower coolant hose from the radiator.
Tightening Torque 30 Nm
Removal & Installation Procedure
1. Disconnect the negative terminal of battery.
2. Remove the hood.

1B3-14 OM600 ENGINE MECHANICAL
9. Loosen the bolt and remove the coolant pipe and cooling
fan shroud.
10. Remove the hoses (air intake to intercooler, intercooler to
intake duct). 8. Disconnect the upper coolant hose from the radiator.
Tightening Torque 3 -7 Nm
11. Remove the pipes connected to intercooler.

1B3-40 OM600 ENGINE MECHANICAL
Disassembly Procedure
1. Completely drain the coolant from the radiator and cylinder
block.
2. Remove the cooling fan shroud.
3. Hold the fan with counter holder and remove the bolt and
then remove the cooling fan.
Notice
Keep the fan in vertical position.
Counter Holder 603 589 00 40 00
5. Remove the nut.
6. Remove the nut on the tensioning lever and insert the
rod(F12 ´ 180mm). By pushing the rod to the arrow direction,
pull back the bolt.
7. Push the tensioning lever to the opposite direction to release
the spring tension and remove the poly V-belt. 4. Remove the bracket oil dipstick tube.

SECTION 1D1
M162 ENGINE COOLING
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1D1-1
General Specifications . . . . . . . . . . . . . . . . . 1D1-1
Fastener Tightening Specifications . . . . . . . . 1D1-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1D1-3
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1D1-3
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1D1-4
System Leakage Test . . . . . . . . . . . . . . . . . . 1D1-4
Maintenance and Repair . . . . . . . . . . . . . . 1D1-5
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1D1-5Coolant Drain and Fill Up . . . . . . . . . . . . . . . 1D1-5
Coolant Connection Fitting . . . . . . . . . . . . . . 1D1-7
Water Pump . . . . . . . . . . . . . . . . . . . . . . . . . 1D1-8
Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . 1D1-10
Oil Cooler Pipe Line . . . . . . . . . . . . . . . . . . 1D1-11
Cooling Fan and Viscous Clutch . . . . . . . . . 1D1-12
Cooling Fan Shroud . . . . . . . . . . . . . . . . . . 1D1-14
Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . 1D1-15
SPECIFICATIONS
GENERAL SPECIFICATIONS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
TABLE OF CONTENTS
Description
Water Cooling Forced Circulation
Double Cross Flow
70,000 kcal/h
580 x 482 x 45 mm

f 460, Six Blades
ALUTEC - P78
50 : 50
11.3 L
3.4 L
1.4 bar Application
Cooling Type
Radiator
Dimension(Width´Height´Thickeness)
Cooling Fan
Anti-Freeze Agent
Mixing Ratio of Anti-Freeze Agen with Water (Anti-Freeze Agent : Water)
Coolant Capacity
Reservoir Capacity
Cap Operating Pressure (Reservoir Tank Pressure Cap)
Circulation Type
Radiation Capability

M162 ENGINE COOLING 1D1-5
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
COOLANT DRAIN AND FILL UP
Draning & Filling up Procedure
1. Loosen the cap a little and release pressure and remove
the cap.
Notice
For the risk of scalding, the cap must not be opened unless
the coolant temperature is below 90
oC.
2. Loosen the radiator lower drain cock and drain the coolant.
Notice
Collect coolant by using a proper container.
3. Drain the coolant from the crankcase by inserting a hose
(dia. 14mm) onto the drain bolt on the side of crankcase
(exhaust manifold) and by loosening the plug.
Notice
lJust loosen the drain plug to drain the coolant and do
not remove the plug completely.
lCollect coolant by using proper container.
4. After complete draining of the coolant, remove the hose
connector to drain plug and reinstall the drain plug.
Installation Notice
5. Tighten the radiator lower drain cock.
Tightening Torque 30 Nm

M162 ENGINE COOLING 1D1-7
COOLANT CONNECTION FITTING
Preceding Work : Removal of cooling fan shroud
1 Bolt (M8 X 100, 2 pieces)...............22.5-27.5 Nm
2 Engine Hanger Bracket
3 Coolant Outlet Port
Removal & Installation Procedure
1. Drain coolant from the radiator.
2. Remove the hose mounting clamp (5) and disconnect the
coolant hose (6).
3. Remove the two bolts (1), the engine hanger bracket (2)
and coolant outlet port (3).
Installation Notice4 O-ring
5 Hose Mounting Clamp
6 Hose
Replace the O-ring with new one.
4. Installation should follow the removal procedure in the
reverse order.
5. Fill up the coolant as specified.
6. Check the leaks in the cooling system.
Tightening Torque22.5 - 27.5 Nm

1D1-10 M162 ENGINE COOLING
THERMOSTAT
Removal & Installation Procedure
1. Drain the coolant from the radiator.
2. Loosen the hose mounting clamp (6) and remove the heater
hose (7).
3. Unscrew the three bolts (5) and remove the thermostat cover
bracket, thermostat cover and the thermostat in order.
Installation Notice 1 Thermostat Cover
2 Thermostat
3 O-ring
4 Thermostat Cover Bracket5 Bolt (M6 X 25, 3 pieces).........................9-11 Nm
6 Hose Mounting Clamp
7 Heater Hose
Do not separate the thermostat cover and thermostat.
4. Replace the O-ring if necessary.
5. Check the leakage in the cooling system.
Tightening Torque 9 - 11 Nm

1D1-14 M162 ENGINE COOLING
COOLING FAN SHROUD
Removal & Installation Procedure
1. Pull out the 2 clips (1) from the fan shroud assembly.
2. Remove the lower fan shroud (2).
Notice
For installation, exactly align the lower fan shroud pin into
the hole of the fan shroud assembly (4) and insert the
clips.
3. Remove the bolts (3) and then remove the cooling fan
shroud assembly (4). 1 Clip
2 Lower Fan Shroud
3 Bolt
Installation Notice
4. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 7 Nm4 Fan Shroud Assembly
5 Radiator

M162 ENGINE COOLING 1D1-15
RADIATOR
Preceding Work : Removal of cooling fan shroud
1 Radiator Inlet Coolant Hose
2 Radiator Outlet Coolant Hose
3 Make Up Coolant Hose
4 Automatic Transmission Oil Cooling Hose
5 Automatic Transmission Oil Cooling Line6 Bolt
7 Insulator
8 Stopper
9 Bolt............................................................. 7 Nm
10 Radiator