engine oil SSANGYONG MUSSO 2003 Service Manual

1B3-158 OM600 ENGINE MECHANICAL
CRANKSHAFT SPROCKET
Preceding Work : Removal of oil panRemoval of timing case cover
1 12-Sided Stretch Bolt (M11) .. Check, 25Nm + 90 °
2 Washer
3 Camshaft Sprocket
4 Timing Chain
5 Bearing Pin
6 Bearing Pin
7 Oil Pump
8 Oil Pump Sprocket
9 Oil Pump Chain
10 Washer 11 Bolt
............................................................ 25Nm
12 Crankshaft Sprocket
13 Crankshaft
15 Key
16 Guide Rail
17 Spring
18 Bushing
19 Tensioning Lever

OM600 ENGINE MECHANICAL 1B3-159
Special Tools
116 589 07 15 00 Drift102 589 05 33 00 Puller Removal Procedure
1. Pull out the tensioning lever (19) together with the spring(17) and guide rail (16) far enough until the tensioning lever has passed the oil pump chain (9) and is resting againstthe crankshaft (13).
2. Pull out tensioning lever (19), spring (17) and bushing (18) from the bearing pin (6).
3. Pull out the guide rail (16).
4. Remove the bolt(11) and then remove the washer (10), oil pump chin (9) and sprocket (8).

OM600 ENGINE MECHANICAL 1B3-161
Installation Procedure
1. Put the same alignment mark on the new crankshaftsprocket as in the old sprocket. Notice Check the timing chain, camshaft sprocket, injection pump timing sprocket, oil pump chain and oil pump sprocket for
wear and replace if necessary.
2. Install the new crankshaft sprocket (12) by using a drift (21). Notice Align the groove of sprocket and woodruff key (arrow)
exactly. Drift 116 589 07 15 00
3. Fit the timing chain (4) on the crankshaft sprocket (12). Notice Align the alignment marks (arrow) on the chain and sprocket.
4. Install the camshaft sprocket (3).
Tightening Torque 25 Nm + 90 °
Notice Pay attention on the alignment marks and dowel pin (arrow).

1B3-162 OM600 ENGINE MECHANICALNotice If the max. length ‘L’ of the stretch bolt exceeds 53.6mm,
replace it.
5. Fit the oil pump chain (9) on the crankshaft sprocket (12) and insert the oil pump sprocket (8) into the oil pump chain and then install it on the oil pump. Notice The curved side of the oil pump sprocket should face the oil pump.
6. Insert the woodruff key (15).
7. Install the guide rail (16). Attach the spring (17) to guide rail and to tensioning lever together onto the bearing pins (5,6). Notice Ensure that the spring is correctly located in the guide rail (arrow).

OM600 ENGINE MECHANICAL 1B3-163
PISTON
Preceding Work : Removal of the cylinder headRemoval of the oil pump
1 Oil Ring
2 2nd Ring
3 Top Ring
4 Snap Ring.............................................. Replace
5 Piston Pin
6 Piston
7 Connecting Rod Bushing .......................... Check 8 Connecting Rod
9 Connecting Rod Upper Bearing Shell
10 Connecting Rod Lower Bearing Shell 11 Connecting Rod Bearing Cap
12 Connecting Rod Bolt ......................... 35Nm + 90 °
13 Crankcase
14 Cylinder Bore
Notice There are two kinds of connecting rods (for machining) and they are different in weight approx. 15g. When replacing the connecting rod, measure its weight and ensure that a engine has the same weight of connecting rods. If not, there would be a unbalancing of engine.

1B3-166 OM600 ENGINE MECHANICAL Installation Procedure
1. Fit the piston onto the connecting rod so that the arrow(15) and the locking slot (16) are facing in direction of the vehicle.
2. Coat the piston pin (15) with engine oil and insert it by hand. Notice Do not heat up the piston.
3. Install the new snap ring (4) into the grooves (arrow).
4. Check the piston rings (1, 2, 3) and replace them if necessary.
5. Install and arrange the piston rings to be evenly 120 ° from
each ends gap.

OM600 ENGINE MECHANICAL 1B3-167
6. Coat the cylinder bore, connecting rod bearing journal,connecting rod bearing shell and piston with oil.
7. Compress the piston rings with a tensioning strap (7).
Tensioning Strap 000 589 04 14 00
8. Insert the piston assembly into the cylinder with a wooden stick (18). Notice The arrow on the piston crown must point toward the front of vehicle.
9. Insert the connecting rod bearing shells (9, 10). Notice Be careful of the difference in upper and lower bearing shells and not to be changed.
10. Position the connecting rod bearings caps.
Notice Position so that the retaining lugs are on the same side of the connecting rod bearing(arrow).
11. Measure stretch shaft diameter (C) of the connecting rod bolts.
Limit ‘ C ’ 7.1mm

1B3-168 OM600 ENGINE MECHANICAL
12. Coat the bolts (12) with oil and then tighten the bolts.
Tightening Torque40Nm + 90°
13. Rotate the crankshaft and check axial clearance between the connecting rod and crankshaft.
14. Measure clearance between the piston crown and cylinder
Standard Max. 0.12mm
15. Position the piston at TDC and measure the distance between the piston crown and the crankcase surface.
Notice Measure at points marked. Dial Gauge 001 589 00 53 21
Dial Gauge Holder 363 589 02 21 00
Standard Max. 0.965 mm

OM600 ENGINE MECHANICAL 1B3-169
OIL FILTER1 Nut ............................................................ 25 Nm
2 Oil Filter ..................................................... Cover
3 O-Ring ................................................... Replace
4 Oil Filter ...............Element Replace If necessary
5 Oil Filter Housing 6 Bolt (M8)
.................................................... 10Nm
7 Oil Pressure Switch
8 Gasket
9 Bolt ........................................................... 25 Nm

1B3-170 OM600 ENGINE MECHANICAL
Removal & Installation Procedure
1. Remove the oil filter cover and then drain the oil.
2. Remove the oil pressure switch line.
3. Remove the oil filter housing.
4. Clean the sealing surface.
5. Installation should follow the removal procedure in thereverse order.