engine oil SSANGYONG MUSSO 2003 Service Manual

1D1-2 M162 ENGINE COOLINGFASTENER TIGHTENING SPECIFICATIONS
N

 m
30
22.5 - 27.5
9 - 11
9 - 11
9 - 11
40.5 - 49.5
3 - 73 - 7
Application
Coolant Drain PlugEngine Hanger Bracket and Coolant OutletPort Bolt Thermostat Cover Bracket Bolt Oil Cooler Pipe Line BoltCooling Fan BoltViscous Clutch Bolt
Automatic Transmission Oil Cooling Hose Bolt Cooling Fan Shroud Bolt

1D1-8 M162 ENGINE COOLING WATER PUMP Preceding Work : Removal of V-beltRemoval of air admission housing
1 Air Admission Housing
2 Oil Cooler Pipe Line
3 Seal....................................................... Replace
4 Bolt ........................................................ 9-11 Nm
5 Coolant Hose
6 Coolant Hose
7 Outlet Coolant Hose 8 Coolant Hose
9 Inlet Coolant Hose
10 Coolant Pump
11 Bolt ........................................................... 21 Nm
12 Dowel Sleeve
13 Seal ....................................................... Replace

M162 ENGINE COOLING 1D1-11
OIL COOLER PIPE LINE Preceding Work : Removal of upper intake manifold
Tightening Torque 9 - 11 Nm
1 Upper Intake Manifold
2 Bolt (M6 X 35, 1 piece)
...........................9-11 Nm
3 Bolt (M6 X 16, 2 pieces) .........................9-11 Nm4 Oil Cooler Pipe Line
5 O-ring .................................................... Replace
Removal & Installation Procedure
1. Drain the coolant.
2. Unscrew the bolts (2, 3) and remove the oil cooler pipe line (4). Replace the O-ring with new one. Installation Notice
3. Installation should follow the removal procedure in the reverse order.
4. Fill up the coolant as specified.
5. Check the leaks in the cooling system.

M162 ENGINE COOLING 1D1-15
RADIATOR Preceding Work : Removal of cooling fan shroud
1 Radiator Inlet Coolant Hose
2 Radiator Outlet Coolant Hose
3 Make Up Coolant Hose
4 Automatic Transmission Oil Cooling Hose
5 Automatic Transmission Oil Cooling Line 6 Bolt
7 Insulator
8 Stopper
9 Bolt
............................................................. 7 Nm
10 Radiator

1D1-16 M162 ENGINE COOLING Removal & Installation Procedure1. Drain coolant from the radiator.
2. Remove the coolant thermo connector from the radiator.
3. Remove the each coolant hoses.
Tightening Torque 14 Nm
4. Remove the automatic transmission oil cooling hose.
Installation Notice
5. Remove the automatic transmission oil cooling line bolts and then remove the oil cooling line.
6. Remove the radiator upper mounting bolts and then remove the bracket and insulator.
7. Remove the radiator.
8. Check the radiator pin for crack, damage, leakage and bending and replace if necessary.
9. Installation should follow the removal procedure in the reverse order.
10. Do cooling system leakage test.

1D2-2 M161 ENGINE COOLINGFASTENER TIGHTENING SPECIFICATIONS
N

 m
30
22.5 - 27.5
9 - 11
9 - 11
9 - 11
40.5 - 49.5
3 - 73 - 7
Application
Coolant Drain PlugEngine Hanger Bracket and Coolant OutletPort Bolt Thermostat Cover Bracket Bolt Oil Cooler Pipe Line BoltCooling Fan BoltViscous Clutch Bolt
Automatic Transmission Oil Cooling Hose Bolt Cooling Fan Shroud Bolt

M161 ENGINE COOLING 1D2-15
REMOVAL AND INSTALLATION OF RADIATOR Preceding Work : Removal of cooling fan shroud
1 Inlet Hose
2 Hose (to Engine)
3 Hose (to 3-way Connector)
4 Make-up Hose (to Coolant Reservoir)
5 3-way Connector
6 Automatic Transmission Oil Cooling Hose (A/T Equippend Vehicle) 7 Bolt (M6 X 20, 4 pieces)
...........................3-7 Nm
8 Insulator
9 Radiator Bracket
10 Radiator

1D2-16 M161 ENGINE COOLING Removal & Installation Procedure1. Drain coolant from the radiator.
2. Remove the coolant thermo connector from the radiator.
3. Remove the each coolant hoses.
Tightening Torque 14 Nm
4. Remove the automatic transmission oil cooling hose.
Installation Notice
5. Unscrew the bolts from radiator bracket and remove the bracket and insulator. Installation Notice
Tightening Torque 3 - 7 Nm
6. Remove the radiator upper mounting bolts and then remove the bracket and insulator.
7. Remove the radiator.
8. Check the radiator pin for crack, damage, leakage and bending and replace if necessary.
9. Installation should follow the removal procedure in the reverse order.
10. Berform the cooling system leakage test.

OM600 ENGINE COOLING 1D3-13
Removal & Installation Procedure
1. Drain coolant from the radiator.
2. Remove the coolant thermoswich connector from radiator.
3. Remove the each coolant hose.
4. Remove the auto T/M oil cooling hose and cooling line.Installation Notice
5. Loosen the radiator upper mounting bolt and remove the mounting stopper and insulator.
6. Remove the radiator.
7. Check the radiator pin for crack, leakage and bending and replace it if necessany.
8. Installation should follow the removal procedure in the reverse order.
Tightening Torque Hose : 29 - 40Nm

M162 ENGINE ELECTRICAL 1E1-7
1 Ignition Coil Cable Cover
2 Bolt (M6 X 60, 7 pieces)......................... 9-11 Nm
3 Spark Plug
SPARK PLUG Preceding Work : Removal of intake air ductT1/1
Ignition Coil : Cylinder 2 and 5
T1/2 Ignition Coil : Cylinder 3 and 4
T1/3 Ignition Coil : Cylinder 1 and 6