timing belt SSANGYONG MUSSO 2003 User Guide

OM600 ENGINE MECHANICAL 1B3-3
N

 m
12 2525
25 / 90 °
N 

 m
1010 23 32 4
2380 23Application
Stud Bolt Exhaust Manifold Not CamShaft Bearing Cap Bolt
12-Sided Bolt (M11)
Application
Oil Pan Bolt-Socket Bolt
Oil Pan Bolt- M6
Oil Pan Bolt- M23Belt Pulley Bolt Guide Pulley Bolt Guide Pulley Bracket Nut
Chain Tensioner
Tesioning Lever Bolt
Cylinder Head
Application
Camshaft Bearing Cap Bolt Camshaft Sprocket Bolt Exhaust Pipe Bolt& Nut
Chain TensionerInjection NozzleIntake Manifold Not Injection Nozzle Pipe Not
Oil Dipstick Tube BoltScrew Plug M18 x 15 N


 m
25
25 / 90 °
25804025 18 1050
Cam Support & Shaft
Timing Cover

OM600 ENGINE MECHANICAL 1B3-63
TIMING CASE COVER
Preceding Work : Removal of the cooling fanRmoval of the V-belt tensioning device Removal of the vibration damper and hub Removal of the alternator
1 Bolt............................................................ 10Nm
2 Cylinder Head Cover
3 Gasket ................................................... Replace
4 Socket Bolt ................................................ 25Nm
5 Fuel Filter
6 Square Nut
7 Oil Pan
8 Socket Bolt ................................................ 10Nm
9 Bolt .................................................... M6 : 10Nm
M8 : 23Nm 10 Power Steering Pump
11 Bolt
12 Belt Pulley 13 Bolt
............................................................ 32Nm
14 Timing Case Cover
15 Bolt ............................................................ 23Nm
16 Alternator Bracket
17 Bolt ............................................................ 45Nm
18 Bolt ............................................................ 25Nm
19 Bolt ............................................................ 10Nm
20 Closing Cover
21 Socket Bolt ................................................ 23Nm
22 Guide Pulley
23 Bolt .............................................................. 9Nm
24 Guide Pulley Bracket
25 Nut ............................................................. 23Nm

OM600 ENGINE MECHANICAL 1B3-75
Sectional View
3 Socket Bolt
4 Crankshaft Belt Pulley
5 Vibration Damper
6 Bolt
7 Washer
8 Straight Pin
Notice The mounting position of vibration damper is fixed by straight pin (8).
Tools Required 602 589 00 40 00 Engine Lock103 589 00 30 00 Puller 9 Hub
11 Radial Seal
12 Timing Gear Case Cover
13 Key
14 Crankshaft Sprocket
16 Crankshaft

1B3-76 OM600 ENGINE MECHANICAL
Removal Procedure
1. Remove the starter motor and install the engine lock intothe wheel ring gear.
Engine Lock 602 589 00 40 00
2. Remove the poly V-belt.
3. Remove the cooling fan. NoticeKeep the fan in vertical position.
4. Remove the cooling fan belt pulley (2).
5. Place alignment marks (arrow) on the vibration damper (5) and crankshaft belt pulley (4).
6. Remove the timing sensor bracket. Notice
Remove if necessary.

OM600 ENGINE MECHANICAL 1B3-79
5. Install the timing sensor bracket.Notice See the ‘TDC setting ’.
6. Install the cooling fan pulley.
Tightening Torque 10 Nm
7. Install the cooling fan.
8. Install the fan belt.
9. Remove the engine lock.

1B3-152 OM600 ENGINE MECHANICAL
CYLINDER HEAD GUIDE RAIL
Preceding Work : Removal of the cooling fanRemoval of poly V-belt
Removal of chain tensioner
1 Cylinder Head Cover
2 Bolt............................................................ 10Nm
3 Gasket ................................................... Replace
4 Camshaft Sprocket
5 Washer
6 12-Sided Bolt (M11) ............ Inspect, 25Nm + 90 °
7 Tensioning Lever
8 Bolt ............................................................ 23Nm9 Bearing Pin
........................... Sealing Compound
10 Guide Rail
11 Bearing Pin
12 Guide Pulley
13 Socket Bolt ................................................ 23Nm
14 Closing Cover
15 Spring
16 Timing Chain