torque SSANGYONG MUSSO 2003 Service Manual

5B-24 MANUAL TRANSMISSION
7. Install the counter shaft rear bearing outer race, shim andretainer.
Tightening Torque 39 - 52 Nm
Using a punch and hammer, bend the lock tabs on the
retainer.
8. Install the following parts : Install the main shaft into case.
Install the main shaft rear bearing outer race into the
rear of the case.
Install the 4th speed blocking ring onto the front of the
main shaft.
Install the input shaft onto the front of the main shaft.
Install the input bearing retainer without shim onto the
front of the case.
Using a torque wrench, tighten the 4 bolts.
9. Install the 5th speed drive gear and blocking ring on the counter shaft.
10. Install the 5th synchronizer and rail/fork.
11. Install the 5th synchronizer snap ring and oiling funnel.
12. Align the slots of the lever with the rollers of the reverse fork and 5th shift rail. Apply sealer on the 5-R lever pivot bolt and install it into the case.
Tightening Torque 28 Nm
13. Using a needle nose pliers, install the 5-R lever clip.

5C-10 CLUTCH Removal & Installation Procedure
1. Remove the starter motor. Install the special tool to theflywheel through the starter motor mounting holes.
Tightening Torque 47 Nm
Engine Lock 602 589 00 40 00
2. Unscren the release cylinder mounting bolts and remove the release cylinder. Installation Notice
3. Unscrew the clutch housing bolts and remove the clutch housing, release fork and release bearing.Installation Notice
4. Insert the centering pin into the clutch spline. Loosen the clutch cover bolts 1/2 turn in crisscross sequence until the spring tension is released. Notice
Do not remove the bolts at a time, or clutchcover can be damaged or deformed.
Centering Pin 661 589 00 15 00
Tightening Torque 30 - 40 Nm

CLUTCH 5C-11
5. Unscrew the bolts and remove the clutch cover, pressure
plate and clutch disc. NoticeBe careful not to drop the pressure plate and clutch disc.Installation Notice
Tightening Torque 21 - 27 Nm
6. Installation should follow the removal procedure in the reverse order. Notice
Before installation, clean oil and grease on the flywheel surface.
Do not clean the clutch disc and release bearing insolvent.

5C-14 CLUTCH
Removal & Installation Procedure
1. Draw out the fluid.
2. Pull out the snap pin and clevis pin from the clutch pedalconnection.
3. Remove the clutch tube. Installation Notice
Tightening Torque 15 - 18 Nm
Notice Be careful not the fluid contact a painted surface.
4. Remove the master cylinder mounting nuts and pull off the master cylinder.Installation Notice
Tightening Torque 8 - 18 Nm
5. Check the clutch pedal operation.
6. Bleed the clutch system.

5D1-10 TRANSFER CASE (PART TIME 4408)
MAINTENANCE AND REPAIR ON-VEHICLE SERVICE MAINTENANCE OF TRANSFER CASE LUBRICANT Oil Level Check Clean the oil level plug and surrounding area.
Remove the oil level plug and check whether oil is drip out or not.
Tighten the oil level plug.
Oil Change Clean the oil level plug and surrounding area
Place a suitable container under the transfer case.
Remove the oil and tighten the drain plug.
Fill the oil through the oil level plug until oil begins todrip out.
Tighten the oil level plug.
Cautions for oil level check and plugs tightening Do not use an impact wrench to remove or tighten theoil level plug or drain plug since this will damage thethreads in the transfer case.
Tightening Torque 20 - 30 Nm

5D1-12 TRANSFER CASE (PART TIME 4408)
Removal & Installation Procedure
1. Disconnect the negative terminal from the battery.
2. Lift up the vehicle and fix it safely.
3. Remove the drain plug and drain the oil.Reinstall the drain plug.
* If planar damper is installed, unscrew 4 bolts and remove the planar damper.
Installation Notice
Tightening Torque 19 - 30 Nm
4. Remove the breather hose.
5. Disconnect the speedometer cable connector and other cable connectors and wiring harnesses.
6. Support the transfer case with jack and remove the front and rear propeller shafts from the transfer case. Installation Notice
Front
Rear 81 - 89 Nm 70 - 80 NmTightening Torque

TRANSFER CASE (PART TIME 4408) 5D1-13
7. Remove the center mounting nuts and end sides mountingbolts of the cross member and then remove the cross
member. Installation Notice
Tightening Torque(1)
Tightening Torque(2) 21 - 35 Nm62 - 93 Nm
8. Remove the transfer case by removing the bolts attaching
the transfer case to the transmission. Installation Notice Notice Apply long-term grease to the inner spline of the transfer case input shaft.
9. Installation should follow the removal procedure in the reverse order.
Tightening Torque 38 - 51 Nm

5D1-28 TRANSFER CASE (PART TIME 4408)
6. Install the planet carrier assembly onto the input shaftand install the thrust washer. Press the bearing over input shaft.
7. After pressing the bearing, install the retaining ring.
8. Press the pin into the front adapter.
9. Slowly press the oil seal into the front adapter.
10. Install the front adapter assembly. Notice
After installation, make sure that snap ring is correctly installed into the groove.
11. Position the input shaft assembly over front cover and engage into the bearing groove by expanding the ends ofsnap ring.
12. Apply 1.6mm bead of sealant on the mounting face for the transfer case and tighten the 6 bolts.
13. Install the breather.
75 Snap Ring
76 Oil Seal
77 Spiral Pin
78 Front Adapter
82 Sleeve Bearing
8 3 Needle Bearing
8 4 Input Shaft
Item
6 Bolts
Breather Tightening Torque
28 - 48 Nm8 - 20 Nm

5D1-30 TRANSFER CASE (PART TIME 4408)
Oil Pump
1. Install the pump front cover to be the ‘TOP ’ mark down and
turn the cover to be the ‘TOP ’ mark up when installed in
vehicle.
2. Install the 2 pump pins and spring to the output shaft. NoticeFlat surface of the pins must point out and align the center
line of pins and spring.
3. Connect the hose coupling to the strainer coupling and install the strainer foot into the transfer case slot. Notice
The hose coupling must face the pump assembly.
4. Install the pump housing to be the 'REAR' mark up and seat the 2 pump pins inside of the pump housing by moving pump pins inward and compressing the spring.
5. Tighten the hose to pump housing by hose clamp.
6. Position the pump rear cover to be the ‘TOP REAR ’ mark
up and located at the top of transfer case when installed in
vehicle. Position the pump retainer on the cover so that tab
on the retainer is in notch in the transfer case. Apply Loctite
to the bolts and tighten the bolts with turning the output
shaft by hand to make the pump pins move freely. 45 Shaft and Pump Assembly
46 Bolt
47 Pump Retainer
48 Rear Pump Cover
49 Hose Clamp
50 Hose Coupling
54 Pump Housing
52 Pump Pin
53 Spring
54 Front Pump Cover
55 Output Shaft
56 Strainer
40 Snap Ring
41 Spacer
42 Drive Sprocket
43 Driven Sprocket
44 Drive Chain
55 Output Shaft (Rear)
71 Output Shaft (Front)
Drive Chain
1. Position the drive sprocket to the rear output shaft end and
driven sprocket to the front output shaft end.
2. Install the drive chain onto the sprocket.
3. Holding each sprocket to be the drive chain tight and parallel with transfer case, install the drive chain assembly to the output shafts.
4. Rotate the driven sprocket slightly to engage splines on the front output shaft.
5. Install the spacer to the front output shaft and insert the snap ring into the shaft groove over spacer.
Tightening Torque 4 - 8.5 Nm

5D1-32 TRANSFER CASE (PART TIME 4408)
Cover
1. Position the cover to be the open end up on the work table.
2. Position the end of needle bearing to be identification markup and press into the cover until upper end of bearing is
40.47 - 40.97mm below cover face that contacts with transfer case.
3. Press the ball bearing into the cover and install the snap ring .
4. Install remaining parts as follows. Install the 4 O-rings on the stud bolts of the clutch coil
assembly.
Install the clutch coil assembly inside the cover and
tighten 3 nuts.
18 Oil Seal
19 Bushing
20 Nut
21 Clutch Coil Assembly
22 Snap Ring
23 Ball Bearing
24 Needle Bearing
2 5 Cover
Tightening Torque 8 - 11 Nm
Install the bearing and motor bearing into the cover.