wheel torque SSANGYONG MUSSO 2003 Service Manual

GENERAL INFORMATION 0B-15
GENERAL DESCRIPTION
AND SYSTEM OPERATION
GENERAL REPAIR INSTRUCTIONS
If a floor jack is used, the following precautions are recommended.
Park the vehicle on level ground, “ block” the front or rear wheels, set the jack against the frame, raise the vehicle and support it with chassis stands and then perform the service operation.
Before performing the service operation, disconnectthe negative battery cable in order to reduce the chance of cable damaged and burning due to short- cir cuiting.
Use a cover on the body, the seats and the floor to protect them against damage and contamination.
Handle brake fluid and antifreeze solution with care as they can cause paint damage.
The use of proper tools, and the recommended essential and available tools where specified, are important for efficient and reliable performance of the service repairs.
Use genuine DAEWOO parts.
Discard used cotter pins, gaskets, O-rings, oil seals, lock washers and self-locking nuts. Prepare new ones for installation. Normal function of these parts cannot be maintained if these parts are reused.
Keep the disassembled parts neatly in groups to
facilitate proper and smooth reassembly.
Keep attaching bolts and nuts separated, as they vary in hardness and design depending on theposition of the installation.
Clean the parts before inspection or reassembly.
Also clean the oil parts, etc. Use compressed air tomake certain they are free of restrictions.
Lubricate rotating and sliding faces of parts with oil or grease before installation.
When necessary, use a sealer on gaskets to prevent leakage.
Carefully observe all specifications for bolt and nut torques.
When service operation is completed, make a final check to be sure service was done properly and theproblem was corrected.

1B1-44 M162 ENGINE MECHANICALEngine Lock 602 589 00 40 00
2. Remove the start motor and install the engine lock to the
flywheel ring gear.
3. Remove the center bolt.
Installation Notice
Tightening Torque 1st step 200 - 220 Nm
2nd step 90
° +10 °
4. Remove the vibration damper assembly using the puller.
5. Installation should follow the removal procedure in the
reverse order. Notice If possible, don ’t separate the vibration damper and the
pulley.

M162 ENGINE MECHANICAL 1B1-53
FLYWHEEL / DRIVEN PLATE Preceding Work : Removal of manual or automatic transmission
1 Flywheel Mounting Bolt (M10 x 22, 8 pieces)............................................... 1st step 45+5 Nm
2nd step +90 ° +10 °
2 Plate 3 Driven Plate (A/T)
4 Dowel Pin
Service Data Standard (Stretch Bolt)
Nominal Size
Stretch Side Diameter
Bolt Length
Tightening Torque
M x 1.5
8.5 - 0.2 mm 8.0 mm
21.8 - 22.2 mm-
When New
Min. Diameter When NewDd L
1st step 50 Nm, 2nd step 90 °

1B1-54 M162 ENGINE MECHANICAL Removal & Installation Procedure
1. Unscrew the stretch bolt.Installation Notice
Sectional View
1 Oil Pan
2 Cover
3 Crankshaft Front Seal
4 Flywheel MTG Bolt
5 Crankshaft
6 Dowel Pin
7 Plate
8 TGCC
9 Bolt
10 Front Drive Plate
11 Rear Drive Plate
12 Rivet
13 Segment
14 Ring Gear

Replace the bolt when the stretch side diameter (d) of the flywheel mounting bolt is less than 8.0mm.
For the stretch bolt tightening, keep the socket wrench
and Tommy-bar to be 90 ° and tighten as specified.
2. Remove the flywheel for manual transmission vehicles, or the driven plate (3), and plate (2) for Auto. transmission vehicle.
3. Installation should follow the removal procedure in the reverse order. Tightening Torque
1st step 45+5 Nm
2nd step 90
° + 10 °

M161 ENGINE MECHANICAL 1B2-51
Engine Lock 602 589 00 40 00
2. Remove the start motor and install the engine lock to the
flywheel ring gear.
3. Remove the center bolt.
Installation Notice
4. Remove the vibration damper assembly using the puller.
5. Installation should follow the removal procedure in thereverse order. Notice If possible, don ’t separate the vibration damper and the
pulley. Tightening Torque
1st step 180 - 220 Nm2nd step + 90
°

1B2-60 M161 ENGINE MECHANICAL
FLYWHEEL/DRIVEN PLATE Preceding Work : Removal of manual or automatic transmission
1 Flywheel Mounting Bolt(M10 x 22, 8 pieces) ................ 1st Step 45 Nm 2nd Step 90°+10 °
2 Plate 3 Driven Plate (A/T)
4 Dowel Pin
5 Flywheel (M/T)
Service Data Standard (Stretch Bolt)
Nominal Size
Stretch Side Diameter
Bolt Length
Tightening Torque
M x 1.5
8.5 - 0.2 mm 8.0 mm
21.8 - 22.2 mm-
When New
Min. Diameter When NewDd L
1st step 50 Nm, 2nd step 90 °

M161 ENGINE MECHANICAL 1B2-61
Removal & Installation Procedure
1. Unscrew the stretch bolt.Installation Notice
Sectional View
1 Oil Pan
2 Cover
3 Radial Seal
4 Bolt
5 Crankshaft
6 Dowel Pin
7 Washer (Thickness : 3.5 mm)
8 Washer
9 Bolt
10 Front Drive Plate 11 Rear Drive Plate
12 Rivet
13 Segment
14 Ring Gear

Replace the bolt when the stretch side diameter (d) of
the flywheel mounting bolt is less than 8.0mm.
For the stretch bolt tightening, keep the socket wrench
and Tommy-bar to be 90 ° and tighten as specified.
2. Remove the flywheel for manual transmission vehicles, or the driven plate (3), and plate (2) for Auto. transmission vehicle.
3. Installation should follow the removal procedure in the reverse order. Tightening Torque
1st step 45 Nm
2nd step 90
°+5 °

OM600 ENGINE MECHANICAL 1B3-95
3. Remove the flywheel (3), if equipped with manualtransmission. Installation Notice Correctly align the position of dowel pin (2).
Tools Required 602 589 00 40 00 Engine Lock Removal & Installation Procedure
1. Install the engine lock.
Engine Lock 602 589 02 40 00
2. Remove the 12-sided stretch bolts (4). Installation Notice
Tightening Torque 45 Nm + 90 °
Notice If the length ‘L’ of bolts exceeds 22.5mm, replace the bolts.

M162 ENGINE CONTROLS 1F1-65
1 Crankshaft Position Sensor
2 Bolt (M6 X 14)........................................ 9 -11Nm
CRANKSHAFT POSITION SENSOR
Removal & Installation Procedure
1. Disconnect the wiring connector at the crankshaft position
sensor.
2. Unscrew the bolt and remove the crankshaft position sensor unit. Installation Notice
3. Installation should follow the removal procedure in the reverse order. 3 Segment
4 Flywheel
Tightening Torque 9 -11Nm

FRONT SUSPENSION 2C-7
Removal & Installation Procedure
1. Remove the fixing nuts and bolts of the shock absorberand lower arm connection. Installation Notice
2. Remove the connecting nuts of the stabilizer bar link to the lower arm. Installation Notice
3. Turn the height control bolt until the distance between the end of the height control bolt end piece and the bolt end becomes 0-5 mm. Installation Notice Install the torsion bar spring and adjust the distance between the end of the height control bolt and piece end the bolt end to be 50-55 mm. Adjust the vehicle height.
Tightening Torque 60 - 80 Nm
Tightening Torque 16 - 22 Nm
4. Remove the torque arm fixing nuts and bolts and then withdraw the torsion bar spring. Installation Notice
M10 M12
Tightening Torque40 - 60 Nm 60 - 80 Nm
5. Installation should follow the removal precedure in thereverse order.
6. Check and adjust the wheel alignment.